Klaartje De Weerdt
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Klaartje De Weerdt has a total of 118 co-authors. Here are the top co-authors by number of shared publications:
- Barbara Lothenbach
Concrete and Asphalt Laboratory, Empa, Dübendorf, Switzerland
11 shared publications Mette R. Geiker
9 shared publications- Alisa Machner
Professorship for Mineral Construction Materials, TUM School of Engineering and Design, Technical University Munich, Munich, Germany
8 shared publications H. Justnes
8 shared publicationsKnut O. Kjellsen
7 shared publicationsMaciej Zajac
7 shared publications
Latest Publications
- Open Access
- 1 October 2026
- Published by Elsevier in SSRN Electronic Journal
How do novel SCMs affect the hydrate assemblage and compressive strength when replacing up to 50% of the Portland cement?
This study examines how increasing the Portland cement (PC) replacement level from 24 to 35 and 50 wt.% using novel supplementary cementitious materials (SCMs) affects hydrate assemblage and compressive strength. The SCMs evaluated include fly ash (FA), volcanic pozzolan (VPI), metallurgical nonferrous slag (S), and calcined clay (C). FA serves as the benchmark, while VPI, S, and C represent potential SCMs for the Northern European market. Pure PC and limestone composite cements act as references.Cement pastes (w/b = 0.50) were cured sealed at 20 °C for 91 days, and their hydrate assemblages were characterized using TGA, XRD, MIP and SEM-EDS combined with mass-balance calculations. Compressive strength was measured on mortar prisms (w/b = 0.50) cured in saturated lime solution for 91 days.Compressive strength decreased by only ~10 MPa between pure PC (60 MPa) and composite cements with 50% SCM replacement, except for slag, which reached ~57 MPa. The limestone reference achieved only 27 MPa, confirming that SCM reactivity contributes substantially to strength. FA and VPI showed similar reacted amounts (~8 g/100 g cement) regardless of replacement level, leading to lower degrees of reaction at higher SCM contents. Increasing PC replacement resulted in marked decreases in total hydrate formation and increases in porosity, but the persistence of a relatively high compressive strength indicates that the type of hydrates formed in the SCM-containing composite cements contribute more to strength than the hydrates in the PC and limestone references.
- 1 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessHow do novel SCMs affect the hydrate assemblage and compressive strength when replacing up to 50% of the Portland cement?
This study examines how increasing the Portland cement (PC) replacement level from 24 to 35 and 50 wt.% using novel supplementary cementitious materials (SCMs) affects hydrate assemblage and compressive strength. The SCMs evaluated include fly ash (FA), volcanic pozzolan (VPI), metallurgical nonferrous slag (S), and calcined clay (C). FA serves as the benchmark, while VPI, S, and C represent potential SCMs for the Northern European market. Pure PC and limestone composite cements act as references.Cement pastes (w/b = 0.50) were cured sealed at 20 °C for 91 days, and their hydrate assemblages were characterized using TGA, XRD, MIP and SEM-EDS combined with mass-balance calculations. Compressive strength was measured on mortar prisms (w/b = 0.50) cured in saturated lime solution for 91 days.Compressive strength decreased by only ~10 MPa between pure PC (60 MPa) and composite cements with 50% SCM replacement, except for slag, which reached ~57 MPa. The limestone reference achieved only 27 MPa, confirming that SCM reactivity contributes substantially to strength. FA and VPI showed similar reacted amounts (~8 g/100 g cement) regardless of replacement level, leading to lower degrees of reaction at higher SCM contents. Increasing PC replacement resulted in marked decreases in total hydrate formation and increases in porosity, but the persistence of a relatively high compressive strength indicates that the type of hydrates formed in the SCM-containing composite cements contribute more to strength than the hydrates in the PC and limestone references.
- Open Access
- 30 March 2026
- Published by Elsevier in Construction and Building Materials
- Vol. 521
Sodium sulfate, silicate, or carbonate? Activator-specific pathways, kinetics, and strength development in ultra-low-clinker hybrid binders
- 30 March 2026
- Published by Elsevier in Construction and Building Materials
- Vol. 521
Open AccessSodium sulfate, silicate, or carbonate? Activator-specific pathways, kinetics, and strength development in ultra-low-clinker hybrid binders
- Open Access
- 11 February 2026
- Published by Elsevier in SSRN Electronic Journal
Pyrrhotite oxidation and associated alterations in aggregate and cement paste of accelerated laboratory and concrete field samples
Pyrrhotite oxidation in concrete aggregates and the consequent internal sulphate attack are serious durability issues that, in an increasing number of cases, lead to premature deterioration of concrete structures. Strict limits on total sulfur content apply in most standards. Still, the mechanism of early-stage pyrrhotite oxidation in concrete remains poorly understood. This study presents a comprehensive mineralogical investigation of pyrrhotite oxidation using pristine aggregate from the Maskimo quarry (Canada), laboratory mortar bar samples subjected to accelerated testing (12, 27, and 52 weeks), and a field concrete core from Trois-Rivières, QC, Canada. Secondary electron microscope EDS-based automated mineralogy (AM), thermomagnetic analysis, and LECO sulfur quantification were employed to investigate the oxidation sequence and secondary mineral associations. The pyrrhotite alteration was linked to relative Fe and S element migration. Fe was relatively immobile, and AM revealed a progressive transformation of pyrrhotite from surface oxidation to complete replacement by Fe-oxides and ferrihydrite. This was accompanied by sulfate leaching into the cement paste and formation of a complex Fe-O-S-Ca phase, gypsum, and ettringite. Findings underscore the importance of sulfur content and pyrrhotite polytype in predicting expansion behavior. Minor expansion rates in accelerated mortar bar samples, along with the absence of cracking, indicated that secondary ferrioxides and hydroxides are the main contributors to volume change in the early phase of internal sulfate attack. The study identifies distinct mineral assemblages at different stages of ISA and demonstrates the utility of AM in quantifying oxidation progression.
- 11 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessPyrrhotite oxidation and associated alterations in aggregate and cement paste of accelerated laboratory and concrete field samples
Pyrrhotite oxidation in concrete aggregates and the consequent internal sulphate attack are serious durability issues that, in an increasing number of cases, lead to premature deterioration of concrete structures. Strict limits on total sulfur content apply in most standards. Still, the mechanism of early-stage pyrrhotite oxidation in concrete remains poorly understood. This study presents a comprehensive mineralogical investigation of pyrrhotite oxidation using pristine aggregate from the Maskimo quarry (Canada), laboratory mortar bar samples subjected to accelerated testing (12, 27, and 52 weeks), and a field concrete core from Trois-Rivières, QC, Canada. Secondary electron microscope EDS-based automated mineralogy (AM), thermomagnetic analysis, and LECO sulfur quantification were employed to investigate the oxidation sequence and secondary mineral associations. The pyrrhotite alteration was linked to relative Fe and S element migration. Fe was relatively immobile, and AM revealed a progressive transformation of pyrrhotite from surface oxidation to complete replacement by Fe-oxides and ferrihydrite. This was accompanied by sulfate leaching into the cement paste and formation of a complex Fe-O-S-Ca phase, gypsum, and ettringite. Findings underscore the importance of sulfur content and pyrrhotite polytype in predicting expansion behavior. Minor expansion rates in accelerated mortar bar samples, along with the absence of cracking, indicated that secondary ferrioxides and hydroxides are the main contributors to volume change in the early phase of internal sulfate attack. The study identifies distinct mineral assemblages at different stages of ISA and demonstrates the utility of AM in quantifying oxidation progression.
- Open Access
- 11 August 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 492
Short-term durability and environmental integration of dredged sediment-based concrete in seawater
- 11 August 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 492
Open AccessShort-term durability and environmental integration of dredged sediment-based concrete in seawater
- Open Access
Modelling and visualizing the impact of metakaolin on the alkali concentration in cement paste pore solution
- Open Access
- 7 March 2025
- Published by Springer Nature in Materials and Structures
- Vol. 58 (3) , 1-21
Report of RILEM TC 301-ASR: Modelling the impact of SCMs, alkali level and w/b ratio on alkali concentration in pore solution
Supplementary cementitious materials (SCMs) can mitigate alkali-silica reaction by lowering the alkali metal concentration in the pore solution. This is a theoretical study on the applicability of a thermodynamic model (GEMS) and the empirical Taylor model to predict the required replacement level of portland cement (PC) by SCMs to achieve an alkali metal concentration below 300 mmol/L. The SCMs investigated are silica fume (SF), metakaolin (MK), fly ash (FA) and slag. The impact of the alkali content of the PC and the w/b ratio on the required replacement level is modelled and compared to experimental pore solution concentrations. Both models predict a similar impact of the SCM replacement level on the distribution of alkali between the pore solution, C–S–H and unreacted material. The thermodynamic model predicts little impact of the alkali content of PC and the w/b-ratio on the required replacement level, i.e., 20% SF, 20% MK, 40–50% FA and 60–70% slag. This is contrary to the Taylor model, which predicts that the replacement levels of FA and slag ranges from 7 to 58% when increasing the alkali content from 0.47 to 0.93% and from 80 to 10%, when increasing the w/b ratio from 0.3 to 0.9. The required replacement levels for SF and MK vary between 2 and 19% when increasing the alkali content from 0.47 to 0.93%, and from 40 to < 5% when increasing the w/b ratio from 0.3 to 0.9. The main difference between the two models is how they account for the uptake of alkali metals by the C–S–H.
- 7 March 2025
- Published by Springer Nature in Materials and Structures
- Vol. 58 (3) , 1-21
Open AccessReport of RILEM TC 301-ASR: Modelling the impact of SCMs, alkali level and w/b ratio on alkali concentration in pore solution
Supplementary cementitious materials (SCMs) can mitigate alkali-silica reaction by lowering the alkali metal concentration in the pore solution. This is a theoretical study on the applicability of a thermodynamic model (GEMS) and the empirical Taylor model to predict the required replacement level of portland cement (PC) by SCMs to achieve an alkali metal concentration below 300 mmol/L. The SCMs investigated are silica fume (SF), metakaolin (MK), fly ash (FA) and slag. The impact of the alkali content of the PC and the w/b ratio on the required replacement level is modelled and compared to experimental pore solution concentrations. Both models predict a similar impact of the SCM replacement level on the distribution of alkali between the pore solution, C–S–H and unreacted material. The thermodynamic model predicts little impact of the alkali content of PC and the w/b-ratio on the required replacement level, i.e., 20% SF, 20% MK, 40–50% FA and 60–70% slag. This is contrary to the Taylor model, which predicts that the replacement levels of FA and slag ranges from 7 to 58% when increasing the alkali content from 0.47 to 0.93% and from 80 to 10%, when increasing the w/b ratio from 0.3 to 0.9. The required replacement levels for SF and MK vary between 2 and 19% when increasing the alkali content from 0.47 to 0.93%, and from 40 to < 5% when increasing the w/b ratio from 0.3 to 0.9. The main difference between the two models is how they account for the uptake of alkali metals by the C–S–H.
- Open Access
The Distribution, Structure, and Chemical Composition of Alkali-Silica Gels in Calcined Clay Concretes
This study investigates the effect of calcined clays (metakaolin, metasilt, metaclay) on the chemical composition, distribution, and structure of alkali–silica reaction (ASR) gels. Using 10 wt% of calcined clays reduced concrete expansion and minimized cracking but did not inhibit ASR gel formation. Micro X-ray fluorescence mapping revealed an average ASR gel content of 3 wt% in concrete, incorporating up to two-thirds of K2O and nearly all Na2O from the binder. Raman spectroscopy indicated structural similarities among gels in different concrete mixes, with an increased degree of polymerization in the metakaolin-containing concrete. Automated mineralogy identified four gel phases: Si gel, Ca-Si gel, Al-Ca-Si gel, and Al-Si gel. Ca-Si gels are formed at binder interfaces, while non-swellable Al-bearing gels are mainly formed in metakaolin-containing concrete located within aggregates. This study shows that aluminum can be incorporated into gels in calcined clay concretes, altering their structure and potentially affecting their expansion behavior in concrete.
Open AccessThe Distribution, Structure, and Chemical Composition of Alkali-Silica Gels in Calcined Clay Concretes
This study investigates the effect of calcined clays (metakaolin, metasilt, metaclay) on the chemical composition, distribution, and structure of alkali–silica reaction (ASR) gels. Using 10 wt% of calcined clays reduced concrete expansion and minimized cracking but did not inhibit ASR gel formation. Micro X-ray fluorescence mapping revealed an average ASR gel content of 3 wt% in concrete, incorporating up to two-thirds of K2O and nearly all Na2O from the binder. Raman spectroscopy indicated structural similarities among gels in different concrete mixes, with an increased degree of polymerization in the metakaolin-containing concrete. Automated mineralogy identified four gel phases: Si gel, Ca-Si gel, Al-Ca-Si gel, and Al-Si gel. Ca-Si gels are formed at binder interfaces, while non-swellable Al-bearing gels are mainly formed in metakaolin-containing concrete located within aggregates. This study shows that aluminum can be incorporated into gels in calcined clay concretes, altering their structure and potentially affecting their expansion behavior in concrete.
- Open Access
- 1 June 2024
- Published by Walter de Gruyter GmbH in Nordic Concrete Research
- Vol. 70 (1) , 77-97
Hydration of Composite Cements Containing Novel SCMs
The impact of novel supplementary cementitious materials (SCMs) on the phase assemblage and the pore structure in cement pastes was studied and linked to their impact on the compressive strength in mortar. The composite cements analysed had a composition of 78 wt.% Portland cement, 18 wt.% SCM and 4 wt.% limestone filler, and the samples were cured sealed for 91 days at 20°C. The investigated SCMs comprise natural materials such as clays and volcanic rocks (rhyolite and hyaloclastite), and industrial products such as fly ash, slag, oil shale ash, bio-fuel ash or bio-coal fly ash. The results revealed that all the SCMs except oil shale ash contribute to the phase assemblage in a similar way, when clinker is replaced with 18 wt.% SCM. The pore structure of the different cement pastes was similar. Even when the composite cement pastes showed a higher total intruded pore volume compared to the Portland cement paste sample, these samples showed higher compressive strength. This indicates that total intruded porosity is not the only contribution to strength.
- 1 June 2024
- Published by Walter de Gruyter GmbH in Nordic Concrete Research
- Vol. 70 (1) , 77-97
Open AccessHydration of Composite Cements Containing Novel SCMs
The impact of novel supplementary cementitious materials (SCMs) on the phase assemblage and the pore structure in cement pastes was studied and linked to their impact on the compressive strength in mortar. The composite cements analysed had a composition of 78 wt.% Portland cement, 18 wt.% SCM and 4 wt.% limestone filler, and the samples were cured sealed for 91 days at 20°C. The investigated SCMs comprise natural materials such as clays and volcanic rocks (rhyolite and hyaloclastite), and industrial products such as fly ash, slag, oil shale ash, bio-fuel ash or bio-coal fly ash. The results revealed that all the SCMs except oil shale ash contribute to the phase assemblage in a similar way, when clinker is replaced with 18 wt.% SCM. The pore structure of the different cement pastes was similar. Even when the composite cement pastes showed a higher total intruded pore volume compared to the Portland cement paste sample, these samples showed higher compressive strength. This indicates that total intruded porosity is not the only contribution to strength.
- Open Access
- 1 June 2024
- Published by Walter de Gruyter GmbH in Nordic Concrete Research
- Vol. 70 (1) , 125-146
Determining the Influence of Curing Temperature and SCMs on C-A-S-H Composition Using SEM-EDS Hypermaps
Calcium-alumina-silicate-hydrate (C-A-S-H) is the main hydration product formed in Portland composite cement pastes. C-A-S-H is a key phase with regard to the strength and durability of concrete. Proper characterization of C-A-S-H is difficult due to intermixing with other phases, thus limiting the applicability of point scan analyses using scanning electron microscopy (SEM). Recent advances have enabled the use of hypermaps from energy dispersive spectroscopy (EDS) to investigate hydrate phases with better statistics. This study investigated how increased curing temperature and the inclusion of pozzolanic SCMs change the composition of the C-A-S-H, using the edxia plugin and SEM-EDS hypermaps. Composite cement pastes were cured at 20, 38, and 60°C for 180 days before analysis. We discuss the interpretation of the data from hypermaps in comparison to the traditional point scan approach.
- 1 June 2024
- Published by Walter de Gruyter GmbH in Nordic Concrete Research
- Vol. 70 (1) , 125-146
Open AccessDetermining the Influence of Curing Temperature and SCMs on C-A-S-H Composition Using SEM-EDS Hypermaps
Calcium-alumina-silicate-hydrate (C-A-S-H) is the main hydration product formed in Portland composite cement pastes. C-A-S-H is a key phase with regard to the strength and durability of concrete. Proper characterization of C-A-S-H is difficult due to intermixing with other phases, thus limiting the applicability of point scan analyses using scanning electron microscopy (SEM). Recent advances have enabled the use of hypermaps from energy dispersive spectroscopy (EDS) to investigate hydrate phases with better statistics. This study investigated how increased curing temperature and the inclusion of pozzolanic SCMs change the composition of the C-A-S-H, using the edxia plugin and SEM-EDS hypermaps. Composite cement pastes were cured at 20, 38, and 60°C for 180 days before analysis. We discuss the interpretation of the data from hypermaps in comparison to the traditional point scan approach.
- 4 May 2024
- Published by Springer Nature
- p. 52-59
The Effect of Temperature and SCMs on Alkali Metal Distribution in Cement Pastes
- 4 May 2024
- Published by Springer Nature
- p. 52-59
The Effect of Temperature and SCMs on Alkali Metal Distribution in Cement Pastes