YNYusaku F. Nishimura

Yusaku F. Nishimura

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yusaku F. Nishimura has a total of 80 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Understanding Mass Transport and Reaction Environment to Optimize CO2 Electrodialysis Systems

    by Jintong Gao, Yusaku Nishimura, Gong Zhang, Tsuyoshi Hamaguchi, Masaoki Iwasaki, Lenan Zhang

    Electrodialysis (ED) is a critical technology for decarbonization, which can be paired with direct air capture to produce a concentrated CO2 stream for efficient carbon utilization and storage. Although previous studies have significantly advanced CO2 ED at the process, membrane, and system levels, the coupled mass transport and reaction environment governing CO2 regeneration remain insufficiently understood, limiting further improvement in current efficiency. Here we develop a spatially resolved modeling framework for CO2 ED. Our approach captures the interplay among concentration polarization, pH gradient, and reaction localization, thereby enabling direct prediction of CO2 generation rate, proton utilization efficiency, and bubble nucleation barrier. Using three representative electrolytes with distinct acid–base properties, we show that buffering and acidity can substantially reshape ion distributions and reaction zones, which produce electrolyte-specific trade-offs between CO2 regeneration and bubble nucleation. Building on these mechanistic insights, we further identify ED cell geometries and operating conditions that maximize proton utilization efficiency while mitigating undesirable bubble nucleation. This work elucidates mass transport and reaction environment in CO2 ED, providing transport-informed design insights for efficient CO2 regeneration powered by renewable electricity.

  • Electrodialysis Processes to Activate (Bi)Carbonate Solutions in Equilibrium with Atmospheric Low-Concentration CO 2

    by Yusaku F. Nishimura, Masamichi Ikai, Chika Ando, Kazumasa Okamura, Tsuyoshi Hamaguchi, Masaoki Iwasaki

    Carbon capture, utilization and storage (CCUS) technologies are pivotal in mitigating the rise in atmospheric CO 2 and promoting sustainable development. We have been focusing on electrochemical CCU processes, which offer the advantage of operation at ambient temperature and pressure. We developed a novel system combining direct air capture and direct electrochemical (bi)carbonate reduction, mediated by a KHCO 3 –K 2 CO 3 mixed solution (C-solution), and demonstrated a cooperative CCU operation. 1 The current efficiency for CO production, η CO , in this system is still low, so that an important challenge is to improve η CO and reduce energy consumption per produced CO. Previous research demonstrates that η CO reaches 90 % when a CO 2 electrolyzer is operated with a C-solution containing high-activity CO 2 ( i.e. , CO 2 -saturated KHCO 3 aqueous solution). 2 This suggests that η CO should increase if an air-derived C-solution could be activated in some process, which motivates us to study electrodialysis processes. In this talk, we report our recent efforts to improve the energy consumption and the processing rate of dissolved inorganic carbon (DIC, consisting of CO 3 2− , HCO 3 − , dissolved CO 2 ) in electrodialysis processes by investigating the effects of mass transports in liquid-phase compartments on electrodialysis performances. An electrodialysis process was studied in the configuration as schematically shown in Fig. 1. A CO 2 -absorbing solution in equilibrium with atmospheric 0.4 mbar CO 2 (g), which was simulated by the C-solution containing 0.136 mol dm −3 K + and 0.100 mol dm −3 DIC, was supplied at 1 cm 3 min −1 to the middle compartment sandwiched between two cation exchange membranes (CEM, Nafion N115, Chemours). The effect of an electrolyte additive was investigated by adding K 2 SO 4 to the above simulated C-solution. A C-solution containing the lower concentrations of K + and DIC than that introduced to the middle compartment (0.100 mol dm −3 K + and 0.067 mol dm −3 DIC) was supplied to the cathode compartment at a standard flow rate of 1 cm 3 min −1 . The anode compartment was supplied with humidified Ar gas at 30 cm 3 min −1 . The cathode and anode were a 250-nm Pt thin film deposited on a carbon paper (TGP-H-060, Toray) and IrO 2 nanoparticles coated on CEM, respectively. The geometric area of each electrode was set to 6.25 cm 2 . Constant currents were applied between the two electrodes with a potentiostat/galvanostat (SP-240, BioLogic) to induce not only electrode reactions but also inter-compartment cation transfers. The degree of progress in DIC activation, P , and the current efficiency for the reaction, η DIC , were evaluated from the concentrations of K + in C-solutions before and after passing through the electrodialysis cell, which were measured with an ion chromatograph (ICS-5000+, Thermo Fischer Scientific) and a potassium ion electrode (HM-40P, DKK-TOA). Regarding the electrodialysis process shown in Fig. 1, we investigated the effects of electrolyte additives in the simulated CO 2 -absorbing solution and the solution flow rate in the cathode compartment on the energy-related performances of the electrodialysis cell (Fig. 2). Figure 2a indicates that addition of an electrolyte additive (0.050 mol dm −3 K 2 SO 4 for example) decreases voltages during the electrodialysis operation at different constant currents. This is due to decrease in the ionic resistance of the middle compartment brought by the electrolyte additive. Figure 2b describes that increase in the flow rate of the C-solution in the cathode compartment increases η DIC during the electrodialysis operation. This would be caused by preventing the accumulation of the K + ion coming from the middle compartment in the space between the cathode sheet and the neighboring CEM. In addition to the above efforts, the energy consumption in an electrodialysis process for DIC activation to CO 2 can be further improved by making the most of the byproducts formed in electrode reactions. The processing rate of DIC can be increased not only by increasing the applied current but also by rearranging the components of an electrodialysis cell. We have also been investigating these effects on the performances of electrodialysis-utilizing electrochemical processes, which will be discussed comprehensively on the basis of our experimental and simulating works in the conference. References Y. Sakamoto, Y. Nishimura, Y. Mizutani, S. Mizuno, R. Hishinuma, K. Okamura, Y. Takeda, and M. Iwasaki, Carbon Capture Sci. Technol. , 12 , 100225 (2024). E. R. Cave, J. H. Montoya, K. P. Kuhl, D. N. Abram, T. Hatsukade, C. Shi, C. Hahn, J. K. Nørskov, and T. F. Jaramillo, Phys. Chem. Chem. Phys. , 19 , 15856 (2017). Figure 1

  • Open Access

    Improved stability and selectivity of CuFe 2 O 4 -based catalysts for photoelectrochemical CO 2 -to-acetate conversion

    by Naohiko Kato, Shu Saeki, Yusaku F. Nishimura, Yasuhiko Takeda, Shinya Moribe

    The newly developed CuFe 2 O 4 -based catalyst demonstrated stable photoelectrochemical (PEC) CO 2 reduction to produce acetate with high selectivity exceeding 90%, thereby solving the stability issue involved in the conventional CuFeO 2 –based catalyst.


  • Introduction of Ag Nanoparticles onto Cu Catalysts Enhances the Selectivity toward Multicarbon Liquid Products in Electrochemical CO Reduction

    by Ryo Hishinuma, Yuna Takeno, Yusaku F. Nishimura, Masahito Shiozawa, Shintaro Mizuno, Yasuhiko Takeda, Masaoki Iwasaki


  • Ni-Doped β-FeOOH Hyperfine Nanorods Surface-Modified with Ni Species Catalyzing Water Oxidation at Neutral pH: Strained FeOOH Core and Phase-Changing Ni(OH)2

    by Tomiko M. Suzuki, Takamasa Nonaka, Yusaku F. Nishimura, Yoriko Matsuoka, Satoru Kosaka, Naoko Takechi Takahashi, Kosuke Kitazumi, Keiichiro Oh-Ishi, Takeshi Morikawa


  • Electrochemical CO2 reduction improved by tuning the Cu-Cu distance in halogen-bridged dinuclear cuprous coordination polymers

    by Naonari Sakamoto, Keita Sekizawa, Shunsuke Sato, Masataka Ohashi, Takamasa Nonaka, Yusaku F. Nishimura, Kosuke Kitazumi, Takeshi Morikawa, Takeo Arai


  • Guiding the Catalytic Properties of Copper for Electrochemical CO2 Reduction by Metal Atom Decoration

    by Yusaku F. Nishimura, Hong-Jie Peng, Stephanie Nitopi, Michal Bajdich, Lei Wang, Carlos G. Morales-Guio, Frank Abild-Pedersen, Thomas F. Jaramillo, Christopher Hahn

    Tuning bimetallic effects is a promising strategy to guide catalytic properties. However, the nature of these effects can be difficult to assess and compare due to the convolution with other factors such as the catalyst surface structure and morphology and differences in testing environments. Here, we investigate the impact of atomic-scale bimetallic effects on the electrochemical CO2 reduction performance of Cu-based catalysts by leveraging a systematic approach that unifies protocols for materials synthesis and testing and enables accurate comparisons of intrinsic catalytic activity and selectivity. We used the same physical vapor deposition method to epitaxially grow Cu(100) films decorated with a small amount of noble or base metal atoms and a combination of experimental characterization and first-principles calculations to evaluate their physicochemical and catalytic properties. The results indicate that the metal atoms segregate to under-coordinated Cu sites during physical vapor deposition, suppressing CO reduction to oxygenates and hydrocarbons and promoting competing pathways to CO, formate, and hydrogen. Leveraging these insights, we rationalize bimetallic design principles to improve catalytic selectivity for CO2 reduction to CO, formate, oxygenates, or hydrocarbons. Our study provides one of the most extensive studies on Cu bimetallics for CO2 reduction, establishing a systematic approach that is broadly applicable to research in catalyst discovery.


  • Self-assembled Cuprous Coordination Polymer as a Catalyst for CO2 Electrochemical Reduction into C2 Products

    by Naonari Sakamoto, Yusaku F. Nishimura, Takamasa Nonaka, Masataka Ohashi, Nobuhiro Ishida, Kosuke Kitazumi, Yuichi Kato, Keita Sekizawa, Takeshi Morikawa, Takeo Arai


  • Low-Overpotential Electrochemical Water Oxidation Catalyzed by CuO Derived from 2 nm-Sized Cu2(NO3)(OH)3 Nanoparticles Generated by Laser Ablation at the Air–Liquid Interface

    by Teppei Nishi, Shunsuke Sato, Takeo Arai, Yusuke Akimoto, Kosuke Kitazumi, Satoru Kosaka, Naoko Takahashi, Yusaku F. Nishimura, Yoriko Matsuoka, Takeshi Morikawa

    A CuO-based water oxidation electrocatalyst that operates at a low overpotential without strong alkaline conditions was developed using a laser ablation process. A two-step laser ablation, laser ablation of Cu powder in liquid (LAL) followed by laser ablation at the air-liquid interface (LAAL), enabled to the preparation of a mixture of 2 nm-sized orthorhombic (gerhardtite) and metastable monoclinic Cu2(NO3)(OH)3 colloidal nanoparticles. Electrodes in which the colloidal nanoparticles were deposited as precursor on carbon paper (CP) formed the CuO-based catalyst after pre-electrolysis (LAAL-CuO/CP), and the electrodes catalyzed electrochemical water oxidation in 1.0 M Na2CO3 (pH 11.3) with a potential of ca. 1.53 V vs. RHE. This value was lower than the reference electrodes of Cu, Cu2O and CuO/CP, and is the lowest among previously-reported Cu-based water oxidation electrocatalysts. A current density over 10 mA/cm2 was achieved at 1.77 V vs. RHE in the 1.0 M Na2CO3 solution, which is competitive with best CuO catalyst.


  • Operando X-ray absorption spectroscopy of hyperfine β-FeOOH nanorods modified with amorphous Ni(OH) 2 under electrocatalytic water oxidation conditions

    by Takeshi Morikawa, Sheraz Gul, Yusaku F. Nishimura, Tomiko M. Suzuki, Junko Yano

    Operando X-ray absorption spectroscopy was employed to study an active electrocatalyst, hyperfine β-FeOOH nanorods (∅ 3 × 15 nm) surface-modified with amorphous Ni hydroxide. The nearest neighbor structure and valence of Fe3+ ions did not change under water oxidation conditions, while changes in the nearest neighbor ordering of Ni2+ ions and a reversible transition to Ni3+ were observed in accordance with the electrical bias for the reaction.