Zhenyu Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zhenyu Xu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Dequan Shi
School of Materials Science and Engineering, Harbin University of Science and Technology
2 shared publicationsGuili Gao
Weichai Power Co., Ltd
2 shared publicationsAilong Jiang
School of Materials Science and Engineering, Shandong University
1 shared publicationDayong Li
School of Materials Science & Engineering, Harbin University of Science & Technology
1 shared publicationHongda Song
School of Materials Science and Engineering, Harbin University of Science and Technology
1 shared publicationKaijiao Kang
School of Materials Science & Engineering, Harbin University of Science & Technology
1 shared publication
Latest Publications
- 1 May 2021
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 62 (5) , 675-679
Evaluation of Vermicularity of Compacted Graphite Iron Based on Multiple Characteristic Points of Thermal Analysis
The vermiculation effects of compacted graphite cast iron are seriously affected by the metallurgical and technological factors. The change of characteristic points on the cooling curve is attributed to the interaction of these factors, so it is difficult to establish the evaluation relationship between the vermicularity and the characteristic points of thermal analysis curve. Based on the idea of statistics, a method was studied to evaluate the vermicularity of molten iron by comparing with an established characteristic points representation model of hypothetical ideal metallurgical quality state under the production condition. The results showed that the method can meet the requirements of evaluating the vermicularity of molten iron by multiple characteristic points on the cooling curve. As the matching process among cooling curves was omitted, the calculation and evaluation efficiency can be improved. In addition, it is expected to achieve on-line classification and regulation of vermiculation effect in front of furnace by expanding the sample capacity for establishing the characterization model.
- 1 May 2021
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 62 (5) , 675-679
Evaluation of Vermicularity of Compacted Graphite Iron Based on Multiple Characteristic Points of Thermal Analysis
The vermiculation effects of compacted graphite cast iron are seriously affected by the metallurgical and technological factors. The change of characteristic points on the cooling curve is attributed to the interaction of these factors, so it is difficult to establish the evaluation relationship between the vermicularity and the characteristic points of thermal analysis curve. Based on the idea of statistics, a method was studied to evaluate the vermicularity of molten iron by comparing with an established characteristic points representation model of hypothetical ideal metallurgical quality state under the production condition. The results showed that the method can meet the requirements of evaluating the vermicularity of molten iron by multiple characteristic points on the cooling curve. As the matching process among cooling curves was omitted, the calculation and evaluation efficiency can be improved. In addition, it is expected to achieve on-line classification and regulation of vermiculation effect in front of furnace by expanding the sample capacity for establishing the characterization model.
- 1 January 2020
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 61 (7) , 1315-1321
Effect of Heat Treatment Parameters on Properties of Al-4.8Si-1.2Cu-0.5Mg Alloy
The effects of heat treatment parameters including solid solution temperature, transfer time, delay time, aging temperature and time on mechanical properties and electrical conductivity of Al-4.8Si-1.2Cu-0.5Mg alloy were studied by independently altering variables. The experimental results showed that with the increase of solid solution temperature, the tensile strength gradually increases, and the elongation and electrical conductivity monotonously decrease. There is a little effect on the mechanical properties and electrical conductivity when the transfer time is less than 40 s. As the delay time increases, the tensile strength decreases quickly and then increases continuously while the elongation and electrical conductivity increases rapidly and then decreases gradually. The effects of aging temperature and time on the tensile strength and elongation have the same tendency. The electrical conductivity always decreases with the aging temperature while it presents an upward-downward-upward change with the aging time. When the solid solution temperature is 525 degrees C, the transfer time and delay time are below 20 s and 2 h, and aging temperature and time are 160 degrees C and 3-5 h, the alloy can achieved satisfactory properties.
- 1 January 2020
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 61 (7) , 1315-1321
Effect of Heat Treatment Parameters on Properties of Al-4.8Si-1.2Cu-0.5Mg Alloy
The effects of heat treatment parameters including solid solution temperature, transfer time, delay time, aging temperature and time on mechanical properties and electrical conductivity of Al-4.8Si-1.2Cu-0.5Mg alloy were studied by independently altering variables. The experimental results showed that with the increase of solid solution temperature, the tensile strength gradually increases, and the elongation and electrical conductivity monotonously decrease. There is a little effect on the mechanical properties and electrical conductivity when the transfer time is less than 40 s. As the delay time increases, the tensile strength decreases quickly and then increases continuously while the elongation and electrical conductivity increases rapidly and then decreases gradually. The effects of aging temperature and time on the tensile strength and elongation have the same tendency. The electrical conductivity always decreases with the aging temperature while it presents an upward-downward-upward change with the aging time. When the solid solution temperature is 525 degrees C, the transfer time and delay time are below 20 s and 2 h, and aging temperature and time are 160 degrees C and 3-5 h, the alloy can achieved satisfactory properties.
- 1 January 2017
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 53 (22) , 37-42
Evaluation Model of the Metallurgical Status of Base Iron for Ductile Iron Based on the Grey Correlation Theory
- 1 January 2017
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 53 (22) , 37-42
Evaluation Model of the Metallurgical Status of Base Iron for Ductile Iron Based on the Grey Correlation Theory
- 1 January 2016
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 52 (6) , 65-71
Precise Method for Testing Cooling Curve and Eutectic Expansion Curve of Ductile Cast Iron in Front of Furnace
- 1 January 2016
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 52 (6) , 65-71
Precise Method for Testing Cooling Curve and Eutectic Expansion Curve of Ductile Cast Iron in Front of Furnace