APAnindito Purnowidodo

Anindito Purnowidodo

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Anindito Purnowidodo has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Optimization of Tensile Strength in Unidirectional Banana Midrib Fiber-Reinforced Composites

    by Ari Wahjudi, Firman Maulana Ishaq, Djarot B. Darmadi, Anindito Purnowidodo, Agung Sugeng Widodo, Khairul Anam

    Natural fiber-reinforced composites have emerged as sustainable alternatives to synthetic composites owing to their biodegradability, high availability, and low cost. Among them, banana midrib fiber offers great potential as reinforcement due to its high cellulose content and abundance as agricultural waste. This study investigates the optimization of tensile strength in unidirectional banana midrib fiber-reinforced composites by examining the influence of fiber volume fraction. Banana midrib fibers were treated with 3% and 4% Natrium Hydroxide (NaOH) solutions to enhance interfacial bonding and then combined with polyester matrix to fabricate composite specimens. Tensile strength was evaluated experimentally according to ASTM D638 standards, while theoretical predictions based on the Rule of Mixtures and statistical modeling using Response Surface Methodology (RSM) were employed for validation and optimization. The results show that tensile strength increased with fiber content up to a critical volume fraction, which fiber agglomeration led to reduced performance. The maximum tensile strength of 44.4 MPa was achieved at a fiber volume fraction of approximately 42% with 4% NaOH solution. RSM demonstrated strong predictive accuracy, with results closely matching experimental data. These findings confirm that both fiber treatment and optimized fiber loading play a decisive role in achieving superior mechanical performance, supporting the use of banana midrib fibers in sustainable engineering applications.

  • Predictive Maintenance for Mineral Processing Plant: A Machine Learning Approach for Coating Thickness Degradation in Seawater Pipelines

    by Asri Anjasari, Anindito Purnowidodo, Khairul Anam

    Predictive maintenance is a strategic necessity in the mineral processing industry, particularly for seawater pipelines that are highly susceptible to internal coating degradation. Failure to accurately predict the reduction in coating thickness can result in leaks, significant financial losses, and operational disruptions. While machine learning algorithms hold significant potential to enhance prediction accuracy and improve infrastructure reliability, their application in piping systems especially for coating thickness remains limited. This study develops a data-driven maintenance framework using Artificial Neural Networks (ANN) to predict internal coating thickness degradation based on a decade of historical inspection records from 2014 to 2024. To address the challenges of data-driven modeling in industrial contexts, this research incorporates advanced feature engineering, including temporal decomposition of inspection dates and spatial encoding of manhole positions. Furthermore, to mitigate the risks of overfitting inherent in limited industrial datasets, the model integrates Dropout layers and L2 regularization. The findings demonstrate that a regularized ANN architecture can effectively capture non-linear degradation patterns. The proposed model achieves a Coefficient of Determination, R 2 of 0.94 and a Mean Absolute Error, MAE of 25.91 µm. These results are expected to reinforce predictive maintenance strategies, optimize shutdown scheduling from 2026 to 2027, and promote the sustainability of industrial operations through more efficient resource allocation and real-time monitoring potential.

  • Open Access

    Stress analysis of steam turbine rotor using Fluid-Structure Interaction simulation

    by Katanda Fajar Fauzi, Moch. Agus Choiron, Agung Sugeng Widodo, Yudy Surya Irawan, Djarot B. Darmadi, Anindito Purnowidodo

    Steam Power Plant generates electricity due to a device that extracts heat energy from steam and converts it into mechanical work on the rotor. Turbines operate at high pressures and temperatures which may cause potential failures in the rotor. This study aims to determine the stress distribution on the turbine rotor to predict potential failures. The turbine studied is a 15 MW steam turbine with a rotation speed of 3000 rpm, inlet steam pressure of 2 MPa, and inlet steam temperature of 471.2 OC. The study focused on the Curtis stage. Fluid-Structure Interaction (FSI) simulation was performed to determine the interaction between the fluid and the turbine rotor. Computational Fluid Dynamic (CFD) was performed to determine the temperature and pressure hitting the rotor. The temperature and pressure distribution data from the CFD simulation is transferred to the structural simulation as the load received by the rotor. In addition to fluid loads, the rotor experiences centrifugal loads due to rotation and gravity loads. The largest stress received by the turbine rotor is at the front of the rotor with a stress of 347.39 MPa.


  • Multi objective optimization of cylindrical multi cell crash box by using response surface methodology

    by Alyssa Sekar Nurfaza, Moch. Agus Choiron, Anindito Purnowidodo

    The number of traffic fatalities in Indonesia rose every year. Frontal crash was the most frequent of all the crash direction. In order to reducing occupant dea The number of traffic fatalities in Indonesia rose every year. Frontal crash was the most frequent of all the crash direction. In order to reducing occupant dea

  • MULTI-OBJECTIVE DESIGN OF HONEYCOMB HYBRID CRASH BOX UNDER FRONTAL LOADING

    by Fina Andika Frida Astuti, Moch. Agus Choiron, Anindito Purnowidodo, Yudy Surya Irawan

    The MM Science Journal, published since 2008, is a world respected scientific journal. The journal, published in English, is double peer reviewed and competitive in distributing knowledge among domestic and international academics and professionals. Full texts are available on-line on the journal...


  • Crack Propagation Behavior on Metal Laminate of FMLs After a High Tensile Overload Under High Constant Amplitude Load

    by Anindito Purnowidodo, Hilmi Iman

    The crack propagation behaviour on the metal laminate of the FMLs is investigated under constant amplitude loads, which is higher compared to the fatigue strength of the metal laminate, and the subsequent crack propagation behaviours after being highly overloaded. The observation was carried out on the FMLs with the various surface roughness of the metal laminate at the interface between the metal and fibre-reinforced composite laminate. The overload leads to delay of the crack propagation following the overload, and the higher surface roughness increases the number of delay cycles. The overload together with the surface roughness affects stress condition in front of the crack tip and the crack tip condition as well as the compressive residual stress in front of the crack tip after the overload. In addition, the higher surface roughness strengthens the shear strength of the interface leading to the delamination caused by cyclic loads to be more difficult to take place. Therefore, the delay cycles after the overloading become longer.


  • Open Access

    The Effect of Fiber Orientation and Stress Ratio on the Crack Growth Behaviour of Fiber Metal Laminates (FMLs)

    by Anindito Purnowidodo, Khairul Anam, Djarot B. Darmadi, Ari Wahjudi

    The crack growth behavior of fiber metal laminates (FMLs) with fiber orientations of 90°/0° and 45°/45° to load direction was investigated with varying stress ratios of the cyclic constant load. The study shows that crack growth behavior depends on the conditions of the cyclic load and the orientation of the fiberglass orientation. A higher stress ratio of the cyclic constant load causes fatigue life to decrease, and is associated with stress concentration just in front of the crack tip. The stress concentration in the FMLs with 45o/45o fiberglass orientation is higher than that of 90o/0o, which means the fatigue life in the former is shorter. The bridging of the fiber-epoxy composite takes place when the stress ratio of the constant cyclic load is lower than 0.4, which also enhances fatigue life.


  • Open Access

    The relation of crack propagation behaviour and delamination on Fibre Acrylic Laminates under various cyclic conditions

    by Anindito Purnowidodo, Khairul Anam, Bagus Maulidika

    The investigation of the crack propagation behaviour associating with the delamination in the interface of the laminate of the fibre acrylic laminates (FALs) composite is carried out by subjecting the composite to cyclic loads. The cyclic load is controlled by the displacement provided by a fatigue testing machine. The cyclic load was carried out with various displacement ratios, R, values, these are, 0, –1, –3, and –5 in which the displacement amplitude was also varied as high as 0.15, 0.20, 0.30 mm, for every value of R. In the present study, the investigation to the crack propagation behaviour is focused on the negative cyclic of R leading to the composite to be cycled under compressive load. The results obtained in the present study shows that in these cases of the lower value of the displacement ratio of –3 and –5, the fatigue life and the crack length of the FALs increase, and the increasing of the displacement amplitude to 0.30 mm causes both the fatigue life and the crack length to be shorter. The delamination propagation rate is higher in the R=0 case than those in the negative value of R. In addition, the lateral contraction of material to outward over the crack region may contribute to the development of the delamination when the ratio of the displacement cycles is negative, and the lateral contraction is higher when the displacement ratio is more negative. Moreover, the delamination may take place in front of the crack tip when the maximum displacement is 0.20 mm or higher, and it causes the crack propagation to be accelerated

  • Effect of filler volume fraction on mechanical strength and failure mode of aluminium bonded with epoxy-based adhesive

    by Khairul Anam, Anindito Purnowidodo

    The aim of this investigation was to understand the effect of filler volume fraction on mechanical strength and failure mode of aluminium bonded with epoxy-based adhesive. The filler used is iron ore with different filler volume fraction. The filler volume fraction of 0%, 10%, 20%, 30%, 40%, 50%, and 60% was used in this investigation. The mechanical strength of the adhesive joints was determined by utilizing T-peel and single lap-shear tests. The failure mode of the adhesive joints and the distribution of the fillers was examined by using macro and scanning electron microscope photos, respectively. The effect of filler volume fraction on the mechanical strength of adhesive was investigated by choosing the highest peel strength and shear strength. The optimum value in peel and shear tests were attained with filler volume fraction of 30%. The joints fail in mixed failure mode (cohesive and adhesive mode). However, the failure mode of filler with 60% volume fraction is in adhesive mode.


  • Open Access

    The effect of external magnetic flux field in the QTS weldment on the change of fatigue crack propagation behaviors

    by Sugiarto Sugiarto, Rudy Soenoko, Anindito Purnowidodo, Yudy Surya Irawan

    This investigation discusses fatigue crack propagation behaviors on the welded joint of Hot Rolled Quench Tempered Steel (QTS) in which during welding process the fusion zone of the joint was subjected to magnetic flux field. The QTS weldability is not really excellent due to the change of microstructure into tempered martensite, and the possibility of microcrack defect on the welding area is still high. The purpose of the investigation is to know the effect of External Magnetic Flux (EMF) field during welding process on fatigue crack propagation behaviors. The external magnetic flux is applied transversely from two sides of the workpiece using a DC powered solenoid of 0, 3, 6, 9 and 15 Amperes. The effect of EMF is more sensitive to decrease the tensile strength and the fatigue crack propagation rate of the weld area. The result shows that the electromagnetic force on the weld pool increases. It causes the liquid metal circulation rate to increase and welding defects to decrease. This indicates that the liquid metal and filler metal are easily mixed, the release of gas from liquid metal to surface before solidification easily happens. The finding shows that the effect of EMF is more efficient.