Blanka Skočilasová
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Blanka Skočilasová has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Jan Skočilas
Department of Process Engineering, Czech Technical University in Prague, 16600 Prague, Czech Republic
8 shared publications - Josef Soukup
Faculty of Production Technology and Management J. E. Purkyne University in Usti nad Labem. Pasteurova 3334/7 400 01 Usti nad Labem Czech Republic
4 shared publications - Frantisek Klimenda
Faculty of mechanical engineering, University of Jan Evangelista Purkyně in Ústí nad Labem, Pasteurova 1, 400 96 Ústí nad Labem, Czech Republic
2 shared publications - Bystrík Červenka
Faculty of Mechanical Engineering Technical University of Košice Vysokoškolská 4 042 00 Košice Slovak Republic
1 shared publication - Martin Močilan
Faculty of Mechanical Engineering University of Žilina 010 01 Žilina Slovak Republic
1 shared publication - Miroslav Příhoda
Department of Thermal Engineering, Faculty of Materials Science and Technology, VSB–Technical University of Ostrava, 708 33 Ostrava-Poruba, Czech Republic
1 shared publication
Latest Publications
- 1 May 2017
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 89, 67-77
Assessment of railway wagon suspension characteristics
- 1 May 2017
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 89, 67-77
Assessment of railway wagon suspension characteristics
- Open Access
- 1 April 2017
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 17 (2) , 157-163
Heat Loading of Steam Boilers Heating Surfaces
This paper deals with the comparison of an analytical solution of the temperature field of a steam boiler pipe membrane wall using a numerical method calculation in the COSMOS/M programme. The result analysis showed that analytical calculating...
- 1 April 2017
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 17 (2) , 157-163
Open AccessHeat Loading of Steam Boilers Heating Surfaces
This paper deals with the comparison of an analytical solution of the temperature field of a steam boiler pipe membrane wall using a numerical method calculation in the COSMOS/M programme. The result analysis showed that analytical calculating...
- Open Access
- 1 January 2017
- Published by Elsevier in Procedia Engineering
- Vol. 177, 17-24
Vibration of Mechanical System with Higher Degrees of Freedom: Solution of the Frequency Equations
- 1 January 2017
- Published by Elsevier in Procedia Engineering
- Vol. 177, 17-24
Open AccessVibration of Mechanical System with Higher Degrees of Freedom: Solution of the Frequency Equations
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1768 (1) , 020017
Effect of mold material on temperature distribution in alloy cast
The article deals with simulation of solidification of aluminum alloy cast in laboratory mold. The distribution of the temperature fields in the volume of cast was investigated. Four different materials of mold was modelled and the rate of solidification in time of the cast was compared with analytic solution. The model serves for prediction of casting process conditions for specific product. For simulation the ANSYS Fluent software was applied.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1768 (1) , 020017
Effect of mold material on temperature distribution in alloy cast
The article deals with simulation of solidification of aluminum alloy cast in laboratory mold. The distribution of the temperature fields in the volume of cast was investigated. Four different materials of mold was modelled and the rate of solidification in time of the cast was compared with analytic solution. The model serves for prediction of casting process conditions for specific product. For simulation the ANSYS Fluent software was applied.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1745 (1) , 020055
Analysis of hydraulic resistance in conical wye
The fluid flow in the standard pipe element was investigated. Standard CFD tool ANSYS Fluent was applied for fluid flow prediction. The numerical solutions for different turbulence models were compared with experimental data obtained from literature. The integral characteristics (pressure drop) of the pipe element – wye with two inlets and one outlet were used for validation of the numerical results. The air flows in the wye in the turbulent regime. The k-ε, k-ω, and Reynolds Stress model and their modifications were applied for turbulence modelling. Two meshes (coarse and fine) of the model were investigated. The models exhibit good agreements with experimental data.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1745 (1) , 020055
Analysis of hydraulic resistance in conical wye
The fluid flow in the standard pipe element was investigated. Standard CFD tool ANSYS Fluent was applied for fluid flow prediction. The numerical solutions for different turbulence models were compared with experimental data obtained from literature. The integral characteristics (pressure drop) of the pipe element – wye with two inlets and one outlet were used for validation of the numerical results. The air flows in the wye in the turbulent regime. The k-ε, k-ω, and Reynolds Stress model and their modifications were applied for turbulence modelling. Two meshes (coarse and fine) of the model were investigated. The models exhibit good agreements with experimental data.
- Open Access
- 1 December 2015
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 15 (6) , 1043-1048
Nusselt Number Criteria Equations in the Cross Flow over Single Tube
The simple geometry was investigated by analytical simulation in the article. The cylinder cross flow and heat transfer was evaluated. The different Nusselt number equations obtained from literature were mutually compared. The selected range o...
- 1 December 2015
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 15 (6) , 1043-1048
Open AccessNusselt Number Criteria Equations in the Cross Flow over Single Tube
The simple geometry was investigated by analytical simulation in the article. The cylinder cross flow and heat transfer was evaluated. The different Nusselt number equations obtained from literature were mutually compared. The selected range o...
- Open Access
- 1 November 2015
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 15 (5) , 857-860
Glass Furnace Controlling from Saving Energy Aspect
The article is the possibility of energy saving of glass furnaces Bonacci when operating. A proposal to energy saving is aimed at changing of the control process of furnaces and installation of closing doors inlet and outlet ports of furnaces....
- 1 November 2015
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 15 (5) , 857-860
Open AccessGlass Furnace Controlling from Saving Energy Aspect
The article is the possibility of energy saving of glass furnaces Bonacci when operating. A proposal to energy saving is aimed at changing of the control process of furnaces and installation of closing doors inlet and outlet ports of furnaces....
- Open Access
- 1 November 2015
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 15 (5) , 909-914
Solidification of the Aluminium Alloy in the Mold
The process of the aluminum alloy casting was investigated. Two materials of the mold were used to observe the effect of thermal conductivity on the time of the solidification. The simulation of the process was conducted in the CFD software re...
- 1 November 2015
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 15 (5) , 909-914
Open AccessSolidification of the Aluminium Alloy in the Mold
The process of the aluminum alloy casting was investigated. Two materials of the mold were used to observe the effect of thermal conductivity on the time of the solidification. The simulation of the process was conducted in the CFD software re...
- 1 January 2014
- Published by AIP Publishing in AIP Conference Proceedings
Determination of pressure drop coefficient by CFD simulation
The article deals with method applied to the verification of the turbulence models. The turbulence models were used in the simulation of the Newtonian fluid turbulent flow in the circular tube. The principle of the method is in the comparison of the pressure drop obtained by the simulation and the analytic solution. The parameters of the fluid flow were varied with the specified Reynolds number range. The pressure drop of inserted element in the pipe is evaluated.
- 1 January 2014
- Published by AIP Publishing in AIP Conference Proceedings
Determination of pressure drop coefficient by CFD simulation
The article deals with method applied to the verification of the turbulence models. The turbulence models were used in the simulation of the Newtonian fluid turbulent flow in the circular tube. The principle of the method is in the comparison of the pressure drop obtained by the simulation and the analytic solution. The parameters of the fluid flow were varied with the specified Reynolds number range. The pressure drop of inserted element in the pipe is evaluated.