Victor I. Lyamichev

DNA sequence analysis by oligonucleotide binding is often affected by interference with the secondary structure of the target DNA. Here we describe an approach that improves DNA secondary structure prediction by combining enzymatic probing of DNA by structure-specific 5′-nucleases with an energy minimization algorithm that utilizes the 5′-nuclease cleavage sites as constraints. The method can identify structural differences between two DNA molecules caused by minor sequence variations such as a single nucleotide mutation. It also demonstrates the existence of long-range interactions between DNA regions separated by >300 nt and the formation of multiple alternative structures by a 244 nt DNA molecule. The differences in the secondary structure of DNA molecules revealed by 5′-nuclease probing were used to design structure-specific probes for mutation discrimination that target the regions of structural, rather than sequence, differences. We also demonstrate the performance of structure-specific ‘bridge’ probes complementary to non-contiguous regions of the target molecule. The structure-specific probes do not require the high stringency binding conditions necessary for methods based on mismatch formation and permit mutation detection at temperatures from 4 to 37°C. Structure-specific sequence analysis is applied for mutation detection in the Mycobacterium tuberculosis katG gene and for genotyping of the hepatitis C virus.

A rapid and simple method for determining accessible sites in RNA that is independent of the length of target RNA and does not require RNA labeling is described. In this method, target RNA is allowed to hybridize with sequence-randomized libraries of DNA oligonucleotides linked to a common tag sequence at their 5′-end. Annealed oligonucleotides are extended with reverse transcriptase and the extended products are then amplified by using PCR with a primer corresponding to the tag sequence and a second primer specific to the target RNA sequence. We used the combination of both the lengths of the RT-PCR products and the location of the binding site of the RNA-specific primer to determine which regions of the RNA molecules were RNA extendible sites, that is, sites available for oligonucleotide binding and extension. We then employed this reverse transcription with the random oligonucleotide libraries (RT-ROL) method to determine the accessible sites on four mRNA targets, human activated ras (ha-ras), human intercellular adhesion molecule-1 (ICAM-1), rabbit β-globin, and human interferon-γ (IFN-γ). Our results were concordant with those of other researchers who had used RNase H cleavage or hybridization with arrays of oligonucleotides to identify accessible sites on some of these targets. Further, we found good correlation between sites when we compared the location of extendible sites identified by RT-ROL with hybridization sites of effective antisense oligonucleotides on ICAM-1 mRNA in antisense inhibition studies. Finally, we discuss the relationship between RNA extendible sites and RNA accessibility.

The invasive signal amplification reaction has been previously developed for quantitative detection of nucleic acids and discrimination of single-nucleotide polymorphisms. Here we describe a method that couples two invasive reactions into a serial isothermal homogeneous assay using fluorescence resonance energy transfer detection. The serial version of the assay generates more than 10(7) reporter molecules for each molecule of target DNA in a 4-h reaction; this sensitivity, coupled with the exquisite specificity of the reaction, is sufficient for direct detection of less than 1,000 target molecules with no prior target amplification. Here we present a kinetic analysis of the parameters affecting signal and background generation in the serial invasive signal amplification reaction and describe a simple kinetic model of the assay. We demonstrate the ability of the assay to detect as few as 600 copies of the methylene tetrahydrofolate reductase gene in samples of human genomic DNA. We also demonstrate the ability of the assay to discriminate single base differences in this gene by using 20 ng of human genomic DNA.

The invasive signal amplification reaction is a sensitive method for single nucleotide polymorphism detection and quantitative determination of viral load and gene expression. The method requires the adjacent binding of upstream and downstream oligonucleotides to a target nucleic acid (either DNA or RNA) to form a specific substrate for the structure-specific 5‘ nucleases that cleave the downstream oligonucleotide to generate signal. By running the reaction at an elevated temperature, the downstream oligonucleotide cycles on and off the target leading to multiple cleavage events per target molecule without temperature cycling. We have examined the performance of the FEN1 enzymes from Archaeoglobusfulgidus and Methanococcusjannaschii and the DNA polymerase I homologues from Thermusaquaticus and Thermusthermophilus in the invasive signal amplification reaction. We find that the reaction has a distinct temperature optimum which increases with increasing length of the downstream oligonucleotide. Raising the concentration of either the downstream oligonucleotide or the enzyme increases the reaction rate. When the reaction is configured to cycle the upstream instead of the downstream oligonucleotide, only the FEN1 enzymes can support a high level of cleavage. To investigate the origin of the background signal generated during the invasive reaction, the cleavage rates for several nonspecific substrates that arise during the course of a reaction were measured and compared with the rate of the specific reaction. We find that the different 5‘ nuclease enzymes display a much greater variability in cleavage rates on the nonspecific substrates than on the specific substrate. The experimental data are compared with a theoretical model of the invasive signal amplification reaction.