Fang Fang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Fang Fang has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
Kun Liu
National Institute of Metrology (NIM) 100029 Beijing China
6 shared publicationsShaoyang Dai
National Institute of Metrology (NIM) 100029 Beijing China
4 shared publicationsWeiliang Chen
Division of Time and Frequency Metrology, NIM, Beijing, Beijing, CHINA
4 shared publicationsFasong Zheng
National Institute of Metrology (NIM) 100029 Beijing China
3 shared publicationsTianchu Li
3 shared publications- Chen Weiliang
Division of Time and Frequency Metrology, National Institute of Metrology (NIM), Beijing, China
2 shared publications
Latest Publications
- Open Access
Measurement of Ultra-Low Frequency Vibrations Using an Atom Interferometer
Measuring low-frequency and ultra-low-frequency vibration signals is of critical importance in fields such as structural mechanics, geological exploration, aerospace, precision machining, and biomedicine. Existing methods face limitations in achieving both ultra-low-frequency range and high precision. We present an ultra-low-frequency vibration measurement method based on the atom interferometer, capable of measuring vibration signals from 0.01 Hz to DC. The performance of measurement was experimentally demonstrated for vibrations between 0.007 Hz and 0.01 Hz, achieving a sensitivity of . Incorporating active vibration isolation can further enhance the measurement range, increasing the optimal sensitivity to .Open AccessMeasurement of Ultra-Low Frequency Vibrations Using an Atom Interferometer
Measuring low-frequency and ultra-low-frequency vibration signals is of critical importance in fields such as structural mechanics, geological exploration, aerospace, precision machining, and biomedicine. Existing methods face limitations in achieving both ultra-low-frequency range and high precision. We present an ultra-low-frequency vibration measurement method based on the atom interferometer, capable of measuring vibration signals from 0.01 Hz to DC. The performance of measurement was experimentally demonstrated for vibrations between 0.007 Hz and 0.01 Hz, achieving a sensitivity of . Incorporating active vibration isolation can further enhance the measurement range, increasing the optimal sensitivity to . - Open Access
- 27 May 2025
- Published by IOP Publishing in Metrologia
- Vol. 62 (3) , 035005
Uncertainty evaluation of the caesium fountain primary frequency standard NIM6
A new caesium (Cs) fountain clock NIM6 has been developed at the National Institute of Metrology (NIM) in China, for which a comprehensive uncertainty evaluation is presented. A three-dimensional magneto-optical trap loading optical molasses is employed to obtain more cold atoms rapidly and efficiently with a tunable, uniform density distribution. A heat pipe surrounding the flight tube maintains a consistent and stable temperature within the interrogation region. Additionally, a Ramsey cavity with four azimuthally distribution feeds is utilized to mitigate distributed cavity phase shifts. The Cs fountain clock NIM6 achieves a short-term fractional frequency instability of 1.0 × 10 −13 τ −1/2 at high atomic density, and a typical overall fractional type-B uncertainty is estimated to be 2.2 × 10 −16 . Comparisons of frequency between the Cs fountain NIM6 and other Cs fountain primary frequency standards through Coordinated Universal Time have demonstrated an agreement within the stated uncertainties.
- 27 May 2025
- Published by IOP Publishing in Metrologia
- Vol. 62 (3) , 035005
Open AccessUncertainty evaluation of the caesium fountain primary frequency standard NIM6
A new caesium (Cs) fountain clock NIM6 has been developed at the National Institute of Metrology (NIM) in China, for which a comprehensive uncertainty evaluation is presented. A three-dimensional magneto-optical trap loading optical molasses is employed to obtain more cold atoms rapidly and efficiently with a tunable, uniform density distribution. A heat pipe surrounding the flight tube maintains a consistent and stable temperature within the interrogation region. Additionally, a Ramsey cavity with four azimuthally distribution feeds is utilized to mitigate distributed cavity phase shifts. The Cs fountain clock NIM6 achieves a short-term fractional frequency instability of 1.0 × 10 −13 τ −1/2 at high atomic density, and a typical overall fractional type-B uncertainty is estimated to be 2.2 × 10 −16 . Comparisons of frequency between the Cs fountain NIM6 and other Cs fountain primary frequency standards through Coordinated Universal Time have demonstrated an agreement within the stated uncertainties.
- Open Access
Uncertainty Evaluation of the Caesium Fountain Primary Frequency Standard NIM6
A new caesium (Cs) fountain clock NIM6 has been developed at the National Institute of Metrology (NIM) in China, for which a comprehensive uncertainty evaluation is presented. A three-dimensional magneto-optical trap (3D MOT) loading optical molasses is employed to obtain more cold atoms rapidly and efficiently with a tunable, uniform density distribution. A heat pipe surrounding the flight tube maintains a consistent and stable temperature within the interrogation region. Additionally, a Ramsey cavity with four azimuthally distribution feeds is utilized to mitigate distributed cavity phase shifts. The Cs fountain clock NIM6 achieves a short-term stability of 1.0x10-13 τ-1/2 at high atomic density, and a typical overall fractional type-B uncertainty is estimated to be 2.3x10-16. Comparisons of frequency between the Cs fountain NIM6 and other Cs fountain Primary Frequency Standards (PFSs) through Coordinated Universal Time (UTC) have demonstrated an agreement within the stated uncertainties.
Open AccessUncertainty Evaluation of the Caesium Fountain Primary Frequency Standard NIM6
A new caesium (Cs) fountain clock NIM6 has been developed at the National Institute of Metrology (NIM) in China, for which a comprehensive uncertainty evaluation is presented. A three-dimensional magneto-optical trap (3D MOT) loading optical molasses is employed to obtain more cold atoms rapidly and efficiently with a tunable, uniform density distribution. A heat pipe surrounding the flight tube maintains a consistent and stable temperature within the interrogation region. Additionally, a Ramsey cavity with four azimuthally distribution feeds is utilized to mitigate distributed cavity phase shifts. The Cs fountain clock NIM6 achieves a short-term stability of 1.0x10-13 τ-1/2 at high atomic density, and a typical overall fractional type-B uncertainty is estimated to be 2.3x10-16. Comparisons of frequency between the Cs fountain NIM6 and other Cs fountain Primary Frequency Standards (PFSs) through Coordinated Universal Time (UTC) have demonstrated an agreement within the stated uncertainties.
- Open Access
A Transportable Atomic Gravimeter with Constraint-Structured Active Vibration Isolation
Many efforts have been taken in recent years to push atomic gravimeters toward practical applications. We demonstrate an atomic gravimeter named NIM-AGRb2 that is transportable and suitable for high-precision gravity measurements. Constraint-structured active vibration isolation (CS-AVI) is used to reduce the ground vibration noise. The constraint structure in CS-AVI ensures that the isolation platform only has vertical translation, with all other degrees of freedom (DoFs) being constrained. Therefore, the stability of active vibration isolation is enhanced. With the implementation of CS-AVI, the sensitivity of NIM-AGRb2 reached as low as 20.5 μGal/Hz1/2. The short-term sensitivity could be further reduced to 10.8 μGal/Hz1/2 in a seismologic observation station. Moreover, we evaluated the system noise of the gravimeter, and the results were consistent with our observations.
Open AccessA Transportable Atomic Gravimeter with Constraint-Structured Active Vibration Isolation
Many efforts have been taken in recent years to push atomic gravimeters toward practical applications. We demonstrate an atomic gravimeter named NIM-AGRb2 that is transportable and suitable for high-precision gravity measurements. Constraint-structured active vibration isolation (CS-AVI) is used to reduce the ground vibration noise. The constraint structure in CS-AVI ensures that the isolation platform only has vertical translation, with all other degrees of freedom (DoFs) being constrained. Therefore, the stability of active vibration isolation is enhanced. With the implementation of CS-AVI, the sensitivity of NIM-AGRb2 reached as low as 20.5 μGal/Hz1/2. The short-term sensitivity could be further reduced to 10.8 μGal/Hz1/2 in a seismologic observation station. Moreover, we evaluated the system noise of the gravimeter, and the results were consistent with our observations.
- Open Access
Development and Evaluation of a Narrow Linewidth Laser System for 171Yb+ E2 Transition
We report the construction and characterization of a narrow-linewidth laser system to interrogate the E2 clock transitions at 436 nm of ytterbium ions trapped in end-cap traps. The 871 nm seed laser at the fundamental frequency is referenced to a 10 cm long notched ULE cavity. The output of the laser system is delivered to a narrow-linewidth femtosecond fiber comb, which has been referenced to an ultrastable 698 nm laser, with a phase noise-canceled fiber link. The beat between the laser and the comb shows a sub-Hz linewidth, and with a stability better than 2E-15@1~100 s. The performance of the self-developed wavelength extension ports at 871 nm of the narrow linewidth erbium-doped fiber comb with single-point frequency-doubling technique is also verified.
Open AccessDevelopment and Evaluation of a Narrow Linewidth Laser System for 171Yb+ E2 Transition
We report the construction and characterization of a narrow-linewidth laser system to interrogate the E2 clock transitions at 436 nm of ytterbium ions trapped in end-cap traps. The 871 nm seed laser at the fundamental frequency is referenced to a 10 cm long notched ULE cavity. The output of the laser system is delivered to a narrow-linewidth femtosecond fiber comb, which has been referenced to an ultrastable 698 nm laser, with a phase noise-canceled fiber link. The beat between the laser and the comb shows a sub-Hz linewidth, and with a stability better than 2E-15@1~100 s. The performance of the self-developed wavelength extension ports at 871 nm of the narrow linewidth erbium-doped fiber comb with single-point frequency-doubling technique is also verified.
- 23 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (4) , 1752-1760
Bimetal Temperature-Compensated Ramsey Cavity for Atomic Fountain Frequency Standards
A typical Ramsey cavity, commonly used in atomic fountain frequency standards (AFFSs) for microwave interrogation, is sensitive to ambient temperature variation. Then, it becomes one of the main limiting factors for the AFFSs operating in a narrow operating-temperature range and a temperature-well-controlled environment up to now. In this article, a new design of bimetal temperature-compensated Ramsey cavity (BTCRC) based on the thermal expansion self-compensating mechanism is presented and experimentally demonstrated. This cavity is a typical TE $_{011}$ -mode cylindrical microwave resonator with a titanium tube and two oxygen-free copper (OFC) caps. The resonance frequency (RF) of the cavity can be immune to temperature variations if the dimensions of the tube and caps are properly designed. To validate this self-compensating mechanism, a BTCRC resonating at the Rb clock frequency with a $Q$ -factor of about 17 000 is constructed. And its RF thermal coefficient is measured to be 0.73 kHz/ $^{\circ}$ C, which is about 150 times superior to $-$ 115.9 kHz/ $^{\circ}$ C of a typical OFC Rb cavity in the temperature range of 22.48 $^{\circ}$ C–37.48 $^{\circ}$ C. During the operation of AFFSs, this BTCRC ensures that the microwave field amplitude inside the cavity, which dictates the transition probability and thus the contrast of the Ramsey fringes, will be stable in time. In addition, the potential temperature variation-induced frequency shifts due to cavity pulling are significantly minimized.
- 23 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (4) , 1752-1760
Bimetal Temperature-Compensated Ramsey Cavity for Atomic Fountain Frequency Standards
A typical Ramsey cavity, commonly used in atomic fountain frequency standards (AFFSs) for microwave interrogation, is sensitive to ambient temperature variation. Then, it becomes one of the main limiting factors for the AFFSs operating in a narrow operating-temperature range and a temperature-well-controlled environment up to now. In this article, a new design of bimetal temperature-compensated Ramsey cavity (BTCRC) based on the thermal expansion self-compensating mechanism is presented and experimentally demonstrated. This cavity is a typical TE $_{011}$ -mode cylindrical microwave resonator with a titanium tube and two oxygen-free copper (OFC) caps. The resonance frequency (RF) of the cavity can be immune to temperature variations if the dimensions of the tube and caps are properly designed. To validate this self-compensating mechanism, a BTCRC resonating at the Rb clock frequency with a $Q$ -factor of about 17 000 is constructed. And its RF thermal coefficient is measured to be 0.73 kHz/ $^{\circ}$ C, which is about 150 times superior to $-$ 115.9 kHz/ $^{\circ}$ C of a typical OFC Rb cavity in the temperature range of 22.48 $^{\circ}$ C–37.48 $^{\circ}$ C. During the operation of AFFSs, this BTCRC ensures that the microwave field amplitude inside the cavity, which dictates the transition probability and thus the contrast of the Ramsey fringes, will be stable in time. In addition, the potential temperature variation-induced frequency shifts due to cavity pulling are significantly minimized.
- Open Access
- 15 September 2022
- Published by Frontiers Media SA in Frontiers in Physics
- Vol. 10
Development of Rb fountain clock for time keeping
A new Rb fountain clock was built at the National Institute of Metrology with the aim to realize robustness and excellent long-term instability for time keeping. While some basic designs have been adopted from our Cs fountain clocks, new features have been included for improved performance. A double-metal interrogation microwave cavity with a thermal expansion self-compensating mechanism was used to reduce the clock sensitivity to temperature fluctuations for the first time, to our knowledge. Moreover, a compact optical system was developed to ensure robustness. These features dramatically increased the ambient temperature range. The developed Rb fountain clock achieved a typical fractional frequency instability of within 10 days of continuous operation without any intervention, demonstrating the potential for time keeping.- 15 September 2022
- Published by Frontiers Media SA in Frontiers in Physics
- Vol. 10
Open AccessDevelopment of Rb fountain clock for time keeping
A new Rb fountain clock was built at the National Institute of Metrology with the aim to realize robustness and excellent long-term instability for time keeping. While some basic designs have been adopted from our Cs fountain clocks, new features have been included for improved performance. A double-metal interrogation microwave cavity with a thermal expansion self-compensating mechanism was used to reduce the clock sensitivity to temperature fluctuations for the first time, to our knowledge. Moreover, a compact optical system was developed to ensure robustness. These features dramatically increased the ambient temperature range. The developed Rb fountain clock achieved a typical fractional frequency instability of within 10 days of continuous operation without any intervention, demonstrating the potential for time keeping. - 5 May 2022
- Published by Springer Nature
- p. 393-402
A Low Temperature-Sensitive Ramsey Cavity for Rb Fountain Clocks
- 5 May 2022
- Published by Springer Nature
- p. 393-402
A Low Temperature-Sensitive Ramsey Cavity for Rb Fountain Clocks
- 2 February 2021
- Published by IOP Publishing in Chinese Physics B
- Vol. 30 (5) , 050602
Improvement of the short-term stability of atomic fountain clock with state preparation by two-laser optical pumping*
To improve the signal to noise ratio (SNR) and the short-term stability of cesium atomic fountain clocks, the work of two-laser optical pumping is presented theoretically and experimentally. The short-term stability of the NIM6 fountain clock has been improved by preparing more cold atoms in the | F = 4, mF = 0〉 clock state with a shortened cycle time. Two π-polarized laser beams overlapped in the horizontal plane have been applied after launching, one is resonant with | F = 4〉 → | F′ = 4〉 transition and the other is resonant with | F = 3〉 → | F′ = 4〉 transition. With optical pumping, the population accumulated in the | mF = 0〉 clock state is improved from 11% to 63%, and the detection signal is increased by a factor of 4.2, the SNR of the clock transition probability and the short-term stability are also improved accordingly.
- 2 February 2021
- Published by IOP Publishing in Chinese Physics B
- Vol. 30 (5) , 050602
Improvement of the short-term stability of atomic fountain clock with state preparation by two-laser optical pumping*
To improve the signal to noise ratio (SNR) and the short-term stability of cesium atomic fountain clocks, the work of two-laser optical pumping is presented theoretically and experimentally. The short-term stability of the NIM6 fountain clock has been improved by preparing more cold atoms in the | F = 4, mF = 0〉 clock state with a shortened cycle time. Two π-polarized laser beams overlapped in the horizontal plane have been applied after launching, one is resonant with | F = 4〉 → | F′ = 4〉 transition and the other is resonant with | F = 3〉 → | F′ = 4〉 transition. With optical pumping, the population accumulated in the | mF = 0〉 clock state is improved from 11% to 63%, and the detection signal is increased by a factor of 4.2, the SNR of the clock transition probability and the short-term stability are also improved accordingly.
- 1 January 2021
- Published by IOP Publishing in Chinese Physics B
- Vol. 30 (1) , 013701
Cold atom clocks and their applications in precision measurements*
Cold atom clocks have made remarkable progresses in the last two decades and played critical roles in precision measurements. Primary Cs fountain frequency standards have achieved a total uncertainty of a few parts in 1016, and the best optical clock has reached a type B uncertainty below 10−18. Besides applications in the metrology, navigation, etc., ultra-stable and ultra-accurate atomic clocks have also become powerful tools in the basic scientific investigations. In this paper, we focus on the recent developments in the high-performance cold atomic clocks which can be used as frequency standards to calibrate atomic time scales. The basic principles, performances, and limitations of fountain clocks and optical clocks based on signal trapped ion or neutral atoms are summarized. Their applications in metrology and other areas are briefly introduced.
- 1 January 2021
- Published by IOP Publishing in Chinese Physics B
- Vol. 30 (1) , 013701
Cold atom clocks and their applications in precision measurements*
Cold atom clocks have made remarkable progresses in the last two decades and played critical roles in precision measurements. Primary Cs fountain frequency standards have achieved a total uncertainty of a few parts in 1016, and the best optical clock has reached a type B uncertainty below 10−18. Besides applications in the metrology, navigation, etc., ultra-stable and ultra-accurate atomic clocks have also become powerful tools in the basic scientific investigations. In this paper, we focus on the recent developments in the high-performance cold atomic clocks which can be used as frequency standards to calibrate atomic time scales. The basic principles, performances, and limitations of fountain clocks and optical clocks based on signal trapped ion or neutral atoms are summarized. Their applications in metrology and other areas are briefly introduced.