Jorge César Brändle de Motta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jorge César Brändle de Motta has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
Alain Berlemont
4 shared publicationsS. Vincent
4 shared publications- Anirudh Asuri Mukundan3 shared publications
- Cheng Peng
Shandong University
3 shared publications E. Climent
3 shared publications- Lian-Ping Wang
Southern University of Science and Technology
3 shared publications
Latest Publications
- 4 September 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1042, A30
Critical deformation state of binary droplet breakup in turbulence
The deformation and breakup of drops in turbulent flows play a key role in a variety of industrial processes and natural situations. Literature reviews link the breakup of a droplet into two droplets (known as binary breakup) to a critical deformed state (CDS). Based on the droplet static pressure distribution, the CDS is defined as a level of deformation beyond which binary breakup is assumed to be inevitable and deterministic, i.e. even if no further external stresses act on the droplet. This study examines this CDS concept and identifies how sensitive rupture dynamics are to external stresses. These points are addressed using direct numerical simulations of individual droplets evolving in turbulence from their initially spherical state up to fragmentation. A scale-by-scale analysis is employed to describe droplet shape and deformation. It ensures an objective determination of the relevant scales involved in the CDS. The analysis of many simulated droplets shows that binary rupture is always preceded by the formation of a neck, whose narrowing until rupture is predicted by the CDS criterion of the literature. Supplementary simulations show that, depending on the shape of the droplets at the CDS, the turbulence has a negligible, contributory or essential effect on rupture. Thus, the binary breakup of droplets in a turbulent environment depends on the shape of the droplets and on their Ohnesorge number (ratio of viscous forces to capillary and inertial forces). These results suggest that the study should be supplemented with a comprehensive description of droplet morphology.
- 4 September 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1042, A30
Critical deformation state of binary droplet breakup in turbulence
The deformation and breakup of drops in turbulent flows play a key role in a variety of industrial processes and natural situations. Literature reviews link the breakup of a droplet into two droplets (known as binary breakup) to a critical deformed state (CDS). Based on the droplet static pressure distribution, the CDS is defined as a level of deformation beyond which binary breakup is assumed to be inevitable and deterministic, i.e. even if no further external stresses act on the droplet. This study examines this CDS concept and identifies how sensitive rupture dynamics are to external stresses. These points are addressed using direct numerical simulations of individual droplets evolving in turbulence from their initially spherical state up to fragmentation. A scale-by-scale analysis is employed to describe droplet shape and deformation. It ensures an objective determination of the relevant scales involved in the CDS. The analysis of many simulated droplets shows that binary rupture is always preceded by the formation of a neck, whose narrowing until rupture is predicted by the CDS criterion of the literature. Supplementary simulations show that, depending on the shape of the droplets at the CDS, the turbulence has a negligible, contributory or essential effect on rupture. Thus, the binary breakup of droplets in a turbulent environment depends on the shape of the droplets and on their Ohnesorge number (ratio of viscous forces to capillary and inertial forces). These results suggest that the study should be supplemented with a comprehensive description of droplet morphology.
- Open Access
- 26 August 2026
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 11 (8)
Metal-pad-roll instability theory for small-scale models of reduction cells
We present a theoretical model for the metal-pad-roll instability in laboratory-scale experimental models of reduction cells consisting of two stably stratified liquid layers subjected to a vertical electric current and magnetic field. In contrast to most previous studies, we do not rely on the shallow-water approximation and can account for viscous and capillary effects that are prevalent in small-scale experiments. In small cells, dissipation effects are largely attributable to laminar viscous damping, which we calculate analytically using a perturbative formulation of the Stokes boundary layers forming at all container walls and on both sides of the liquid interface. The derived damping rates, which are also useful for modeling liquid-liquid sloshing in rectangular containers, are validated against direct numerical simulations conducted with the coupled level set and volume-of-fluid solver ARCHER. On this basis, we derive analytical solutions for the growth rates and instability onsets of the metal-pad-roll instability, which we compare with different theoretical descriptions and existing experiments. The presented solutions are intended to serve as a foundation for future benchmarking of multiphase solvers.
- 26 August 2026
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 11 (8)
Open AccessMetal-pad-roll instability theory for small-scale models of reduction cells
We present a theoretical model for the metal-pad-roll instability in laboratory-scale experimental models of reduction cells consisting of two stably stratified liquid layers subjected to a vertical electric current and magnetic field. In contrast to most previous studies, we do not rely on the shallow-water approximation and can account for viscous and capillary effects that are prevalent in small-scale experiments. In small cells, dissipation effects are largely attributable to laminar viscous damping, which we calculate analytically using a perturbative formulation of the Stokes boundary layers forming at all container walls and on both sides of the liquid interface. The derived damping rates, which are also useful for modeling liquid-liquid sloshing in rectangular containers, are validated against direct numerical simulations conducted with the coupled level set and volume-of-fluid solver ARCHER. On this basis, we derive analytical solutions for the growth rates and instability onsets of the metal-pad-roll instability, which we compare with different theoretical descriptions and existing experiments. The presented solutions are intended to serve as a foundation for future benchmarking of multiphase solvers.
- Open Access
- 15 July 2026
- Published by Elsevier in SSRN Electronic Journal
OpenFOAM modelling of storm-induced wave run-up and swash hydrodynamics on a macrotidal beach
A real-scale OpenFOAM-based numerical framework is assessed for simulating storm-induced wave run-up on a natural macrotidal beach, benchmarking it against the non-hydrostatic phase-resolving model SWASH and field measurements. The simulations were carried out on a cross-shore transect of Villers-sur-Mer, a macrotidal sandy beach on the Normandy coast of France, under conditions representative of Storm Ciara in the English Channel during February 2020. A numerical wave flume was built with OpenFOAM and the waves2Foam library to reproduce wave propagation, breaking, and swash over the natural bathymetry, from which the extreme run-up (R2%) was extracted. Three sea states were simulated, spanning a range of significant wave heights, peak periods, and water levels, with each case validated independently against timestack-derived field measurements and SWASH predictions. The two high-water cases yielded R2% = 1.68 and 1.59 m with OpenFOAM, in close agreement with the field estimates (1.66 and 1.59m) and the SWASH values (1.66 and 1.56m), with relative errors below 1%. The dissipative low-water case yielded 0.87 m against a field value of 0.91 m (SWASH: 0.88 m), a relative error of approximately 4.4%. Across all three sea states, the predicted run-up showed a physically consistent response to incident wave height, period, and water level. Beyond these exceedance statistics, the two-phase formulation resolves the detailed surf- and swash-zone hydrodynamics, providing physical information inaccessible to depth-integrated models. These results show that OpenFOAM reliably reproduces storm-induced run-up on natural macrotidal beaches and offers a high-fidelity complement to efficient phase-resolving models for coastal flooding.
- 15 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessOpenFOAM modelling of storm-induced wave run-up and swash hydrodynamics on a macrotidal beach
A real-scale OpenFOAM-based numerical framework is assessed for simulating storm-induced wave run-up on a natural macrotidal beach, benchmarking it against the non-hydrostatic phase-resolving model SWASH and field measurements. The simulations were carried out on a cross-shore transect of Villers-sur-Mer, a macrotidal sandy beach on the Normandy coast of France, under conditions representative of Storm Ciara in the English Channel during February 2020. A numerical wave flume was built with OpenFOAM and the waves2Foam library to reproduce wave propagation, breaking, and swash over the natural bathymetry, from which the extreme run-up (R2%) was extracted. Three sea states were simulated, spanning a range of significant wave heights, peak periods, and water levels, with each case validated independently against timestack-derived field measurements and SWASH predictions. The two high-water cases yielded R2% = 1.68 and 1.59 m with OpenFOAM, in close agreement with the field estimates (1.66 and 1.59m) and the SWASH values (1.66 and 1.56m), with relative errors below 1%. The dissipative low-water case yielded 0.87 m against a field value of 0.91 m (SWASH: 0.88 m), a relative error of approximately 4.4%. Across all three sea states, the predicted run-up showed a physically consistent response to incident wave height, period, and water level. Beyond these exceedance statistics, the two-phase formulation resolves the detailed surf- and swash-zone hydrodynamics, providing physical information inaccessible to depth-integrated models. These results show that OpenFOAM reliably reproduces storm-induced run-up on natural macrotidal beaches and offers a high-fidelity complement to efficient phase-resolving models for coastal flooding.
- 31 March 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Simulation des écoulements turbulents avec des particules de taille finie en régime dense
Un grand nombre d'écoulements naturels et industriels mettent en jeu des particules (sédimentation,lit fluidisé, sprays...). Les écoulements chargés en particules sont bien décrits numériquement sous l'hypothèse des particules plus petites que toutes les échelles de l'écoulement. Cette thèse consiste à simuler numériquement une turbulence homogène et isotrope soutenue chargée en particules dont la taille est supérieure à l'échelle de Kolmogorov. Pour se faire une méthode de simulation a été développée au sein du code Thétis puis validée. L'originalité de cette méthode consiste en l'utilisation d'une approche de pénalisation associée à la viscosité dans la zone solide. Les particules sont transportées de façon lagrangienne. Les principaux résultats concernent trois simulations faisant varier le rapport de densité entre le fluide et le solide. Chaque simulation simule le mouvement de 512particules avec un diamètre 22 fois plus grand que l'échelle spatiale de Kolmogorov remplissant ainsi3% du volume total. La dispersion des particules est étudiée et montre des comportements comparables à ceux observés pour des particules ponctuelles. Un intérêt particulier est porté sur le régime collisionnel. On observe que la corrélation des vitesses avec le fluide environnant réduit le nombre de chocs frontaux par rapport au cas théorique de particules d'un gaz dense. L'effet de la prise en compte du fluide visqueux entre les particules (couche de lubrification) lors de la collision a été étudiée. L'écoulement moyen à l'échelle des particules est aussi analysé, mettant en évidence l'existence d'une couche de dissipation autour des particules.
- 31 March 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Simulation des écoulements turbulents avec des particules de taille finie en régime dense
Un grand nombre d'écoulements naturels et industriels mettent en jeu des particules (sédimentation,lit fluidisé, sprays...). Les écoulements chargés en particules sont bien décrits numériquement sous l'hypothèse des particules plus petites que toutes les échelles de l'écoulement. Cette thèse consiste à simuler numériquement une turbulence homogène et isotrope soutenue chargée en particules dont la taille est supérieure à l'échelle de Kolmogorov. Pour se faire une méthode de simulation a été développée au sein du code Thétis puis validée. L'originalité de cette méthode consiste en l'utilisation d'une approche de pénalisation associée à la viscosité dans la zone solide. Les particules sont transportées de façon lagrangienne. Les principaux résultats concernent trois simulations faisant varier le rapport de densité entre le fluide et le solide. Chaque simulation simule le mouvement de 512particules avec un diamètre 22 fois plus grand que l'échelle spatiale de Kolmogorov remplissant ainsi3% du volume total. La dispersion des particules est étudiée et montre des comportements comparables à ceux observés pour des particules ponctuelles. Un intérêt particulier est porté sur le régime collisionnel. On observe que la corrélation des vitesses avec le fluide environnant réduit le nombre de chocs frontaux par rapport au cas théorique de particules d'un gaz dense. L'effet de la prise en compte du fluide visqueux entre les particules (couche de lubrification) lors de la collision a été étudiée. L'écoulement moyen à l'échelle des particules est aussi analysé, mettant en évidence l'existence d'une couche de dissipation autour des particules.
- Open Access
- 8 May 2025
- Published by Elsevier in Physica D: Nonlinear Phenomena
- Vol. 477
Study of interface coupling in three-layer viscous fluid systems
- 8 May 2025
- Published by Elsevier in Physica D: Nonlinear Phenomena
- Vol. 477
Open AccessStudy of interface coupling in three-layer viscous fluid systems
- Open Access
- 11 January 2024
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 173
Breakup prediction of oscillating droplets under turbulent flow
- 11 January 2024
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 173
Open AccessBreakup prediction of oscillating droplets under turbulent flow
- Open Access
- 30 May 2023
- Published by Frontiers Media SA in Frontiers in Physics
- Vol. 11
Droplet oscillations in a turbulent flow
The oscillations of an initially unperturbed spherical droplet immersed in a homogeneous and isotropic turbulent background flow are investigated through spherical harmonic decomposition. As suggested in the literature, the shape oscillations under turbulent conditions are related to the frequency of droplets oscillating in a fluid without background flow. A series of direct numerical simulations (DNS) of droplets with single deformation modes in a fluid at rest are first performed. The frequency and damping rate are compared with weakly viscous linear theory. Then, a database of 220 droplets deformed under turbulent conditions for a single Weber and Reynolds number is generated with an identical numerical set-up. Each spherical harmonic coefficient shows an oscillatory motion with comparable frequency to the single deformation mode simulations. The power spectrum of the coefficients provides the amount of surface of each mode. After a transient regime, the surface area reaches a stationary saturation level. The saturation level of each mode is linked to the turbulence and the energy stored at the interface. Droplets after a high deformation are studied with and without background flow. As expected, the physics of relaxation is driven by capillary forces.
- 30 May 2023
- Published by Frontiers Media SA in Frontiers in Physics
- Vol. 11
Open AccessDroplet oscillations in a turbulent flow
The oscillations of an initially unperturbed spherical droplet immersed in a homogeneous and isotropic turbulent background flow are investigated through spherical harmonic decomposition. As suggested in the literature, the shape oscillations under turbulent conditions are related to the frequency of droplets oscillating in a fluid without background flow. A series of direct numerical simulations (DNS) of droplets with single deformation modes in a fluid at rest are first performed. The frequency and damping rate are compared with weakly viscous linear theory. Then, a database of 220 droplets deformed under turbulent conditions for a single Weber and Reynolds number is generated with an identical numerical set-up. Each spherical harmonic coefficient shows an oscillatory motion with comparable frequency to the single deformation mode simulations. The power spectrum of the coefficients provides the amount of surface of each mode. After a transient regime, the surface area reaches a stationary saturation level. The saturation level of each mode is linked to the turbulence and the energy stored at the interface. Droplets after a high deformation are studied with and without background flow. As expected, the physics of relaxation is driven by capillary forces.
- 2 March 2023
- Published by Elsevier in Computers & Fluids
- Vol. 256
A coupled Eulerian interface capturing and Lagrangian particle method for multiscale simulation
- 2 March 2023
- Published by Elsevier in Computers & Fluids
- Vol. 256
A coupled Eulerian interface capturing and Lagrangian particle method for multiscale simulation
- 1 February 2022
- Published by Elsevier in Journal of Computational Physics
- Vol. 451
A hybrid moment of fluid–level set framework for simulating primary atomization
- 1 February 2022
- Published by Elsevier in Journal of Computational Physics
- Vol. 451
A hybrid moment of fluid–level set framework for simulating primary atomization
- 1 January 2021
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 38 (2) , 3233-3241
DNS and LES of primary atomization of turbulent liquid jet injection into a gaseous crossflow environment
- 1 January 2021
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 38 (2) , 3233-3241
DNS and LES of primary atomization of turbulent liquid jet injection into a gaseous crossflow environment