LLLiyin Li

Liyin Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Liyin Li has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental and Numerical Simulation Investigation on Laser Flexible Shock Micro-Bulging

    by Huixia Liu, Xianqing Sun, Zongbao Shen, Liyin Li, Chaofei Sha, Youjuan Ma, Jenn-Terng Gau, Xiao Wang

    Laser flexible shock micro-bulging (LFSB) is a novel micro fabrication technology, which combines laser dynamic forming and flexible die forming, which is a type of high strain rate micro-forming. The LFSB of 304 stainless steel foils was investigated in this paper. Experimental and simulated results indicated that the bulging depth and thickness thinning rate of bulging parts increased with an increase of laser energy and a decrease of workpiece thickness. Experimental results also showed the surface morphology of bulging parts. The hardness distribution in the cross section of bulging parts was revealed by nanoindentation experiments. The internal microstructure of micro bulging parts was observed by TEM. In addition, the equivalent stress and plastic strain distribution of bulging parts were shown in the numerical simulation under different workpiece thicknesses and laser energies.


  • Open Access

    Investigation on a Novel Laser Impact Spot Welding

    by Huixia Liu, Shuai Gao, Zhang Yan, Liyin Li, Cong Li, Xianqing Sun, Chaofei Sha, Zongbao Shen, Youjuan Ma, Xiao Wang

    In this paper a novel laser impact spot welding (LISW) method is described, in which a hump was formed on the flyer plate on the intended welding spot location by local pre-forming. When the flyer and base plates were placed together to perform welding, the two plates kept in contact over their entire surfaces except at the hump, where a local air gap was enough to guarantee the impact velocity and collision angle to achieve spot welding using laser pulse energy. The presented approach was implemented to join thin titanium foils to copper foils under low laser energy system. Joints with regular shapes were obtained. The microstructure in the weld interface was studied with scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). It was found that the jetting occurred at the central region of the weld spots due to oblique impact. Wave features were observed in the weld interfaces. The impact energy was found to have significant influence on the wave’s characteristics. Moreover, SEM images and EDS analysis did not show apparent element diffusion across the weld interface. Besides, the lap shearing test was used to characterize the mechanical properties of the spot welded joints.


  • Open Access

    The Investigation on Mask and Plasticine Laser Shock Forming

    by Liyin Li, Xiao Wang, Zongbao Shen, Huixia Liu, Youjuan Ma

    A novel technology called mask and plasticine laser shock forming (MAPLSF) was introduced to manufacture micro-features on the surface of pure copper foil with the thickness of 40μm. In this process, the laser-generated shock wave and plasticine are used to replace the conventional rigid punch and die. The result showed that the shape of laser beam can be roughly manufactured on the surface of the workpiece and this mold-free laser shock forming process is a fast method to fabricate controlled micro-feature on the metallic foils. In this damage-free forming process, the workpicec can keep good surface, because the plasticine is softer than metal foils.

  • Open Access

    An Experimental Study on Micro Clinching of Metal Foils with Cutting by Laser Shock Forming

    by Xiao Wang, Cong Li, Youjuan Ma, Zongbao Shen, Xianqing Sun, Chaofei Sha, Shuai Gao, Liyin Li, Huixia Liu

    This paper describes a novel technique for joining similar and dissimilar metal foils, namely micro clinching with cutting by laser shock forming. A series of experiments were conducted to study the deformation behavior of single layer material, during which many important process parameters were determined. The process window of the 1060 pure aluminum foils and annealed copper foils produced by micro clinching with cutting was analyzed. Moreover, similar material combination (annealed copper foils) and dissimilar material combination (1060 pure aluminum foils and 304 stainless steel foils) were successfully achieved. The effect of laser energy on the interlock and minimum thickness of upper foils was investigated. In addition, the mechanical strength of different material combinations joined by micro clinching with cutting was measured in single lap shearing tests. According to the achieved results, this novel technique is more suitable for material combinations where the upper foil is thicker than lower foil. With the increase of laser energy, the interlock increased while the minimum thickness of upper foil decreased gradually. The shear strength of 1060 pure aluminum foils and 304 stainless steel foils combination was three times as large as that of 1060 pure aluminum foils and annealed copper foils combination.


  • Open Access

    Fabrication of Dish-Shaped Micro Parts by Laser Indirect Shocking Compound Process

    by Huixia Liu, Chaofei Sha, Zongbao Shen, Liyin Li, Shuai Gao, Cong Li, Xianqing Sun, Xiao Wang

    Compound process technology has been investigated for many years on a macro scale, but only a few studies can be found on a micro scale due to the difficulties in tool manufacturing, parts transporting and punch-die alignment. In this paper, a novel technology of combining the laser shock wave and soft punch was introduced to fabricate the dish-shaped micro-parts on copper to solve these difficulties. This compound process includes deep drawing, punching and blanking and these processes can be completed almost at the same time because the duration time of laser is quite short, so the precision of the micro-parts can be ensured. A reasonable laser energy of 1550 mJ made the morphology, depth of deformation, dimensional accuracy and surface roughness achieve their best results when the thickness of the soft punches was 200 μm. In addition, thicker soft punches may hinder the compound process due to the action of unloading waves based on the elastic wave theory. So, the greatest thickness of the soft punches was 200 μm.