Pietro Romanazzi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Pietro Romanazzi has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
David A. Howey
Department of Engineering Science University of Oxford Parks Road Oxford OX1 3PJ UK
1 shared publication- David A. Howey
Department of Engineering Science University of Oxford Oxford UK
1 shared publication - Maria Bruna
Mathematical Institute, University of Oxford, Oxford OX2 6GG, UK
1 shared publication
Latest Publications
- 30 August 2016
- Published by Wiley in Journal of Heat Transfer
- Vol. 139 (1) , 012101
Thermal Homogenization of Electrical Machine Windings Applying the Multiple-Scales Method
Low-order thermal models of electrical machines are fundamental for the design and management of electric powertrains since they allow evaluation of multiple drive cycles in a very short simulation time and implementation of model-based control schemes. A common technique to obtain these models involves homogenization of the electrical winding geometry and thermal properties. However, incorrect estimation of homogenized parameters has a significant impact on the accuracy of the model. Since the experimental estimation of these parameters is both costly and time-consuming, authors usually prefer to rely either on simple analytical formulae or complex numerical calculations. In this paper, we derive a low-order homogenized model using the method of multiple-scales (MS) and show that this gives an accurate steady-state and transient prediction of hot-spot temperature within the windings. The accuracy of the proposed method is shown by comparing the results with both high-order numerical simulations and experimental measurements from the literature.
- 30 August 2016
- Published by Wiley in Journal of Heat Transfer
- Vol. 139 (1) , 012101
Thermal Homogenization of Electrical Machine Windings Applying the Multiple-Scales Method
Low-order thermal models of electrical machines are fundamental for the design and management of electric powertrains since they allow evaluation of multiple drive cycles in a very short simulation time and implementation of model-based control schemes. A common technique to obtain these models involves homogenization of the electrical winding geometry and thermal properties. However, incorrect estimation of homogenized parameters has a significant impact on the accuracy of the model. Since the experimental estimation of these parameters is both costly and time-consuming, authors usually prefer to rely either on simple analytical formulae or complex numerical calculations. In this paper, we derive a low-order homogenized model using the method of multiple-scales (MS) and show that this gives an accurate steady-state and transient prediction of hot-spot temperature within the windings. The accuracy of the proposed method is shown by comparing the results with both high-order numerical simulations and experimental measurements from the literature.
- Open Access
Air-Gap Convection in a Switched Reluctance Machine
Switched reluctance machines (SRMs) have recently become popular in the automotive market as they are a good alternative to the permanent magnet machines commonly employed for an electric powertrain. Lumped parameter thermal networks are usually used for thermal analysis of motors due to their low computational cost and relatively accurate results. A critical aspect to be modelled is the rotor-stator air-gap heat transfer, and this is particularly challenging in an SRM due to the salient pole geometry. This work presents firstly a review of the literature including the most relevant correlations for this geometry, and secondly, numerical CFD simulations of air-gap heat transfer for a typical configuration. A new correlation has been derived: $\mathbf{Nu=0.181\ Ta_m^{0.207}}$Open AccessAir-Gap Convection in a Switched Reluctance Machine
Switched reluctance machines (SRMs) have recently become popular in the automotive market as they are a good alternative to the permanent magnet machines commonly employed for an electric powertrain. Lumped parameter thermal networks are usually used for thermal analysis of motors due to their low computational cost and relatively accurate results. A critical aspect to be modelled is the rotor-stator air-gap heat transfer, and this is particularly challenging in an SRM due to the salient pole geometry. This work presents firstly a review of the literature including the most relevant correlations for this geometry, and secondly, numerical CFD simulations of air-gap heat transfer for a typical configuration. A new correlation has been derived: $\mathbf{Nu=0.181\ Ta_m^{0.207}}$