Sung-Il Chung
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sung-Il Chung has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Pan Kyeom Kim
Nano Hybrid Technology Research Center, Korea Electrotechnology Research Institute, Changwon 51543, Republic of Korea
7 shared publications Tae-Gyu Ha
Nano Hybrid Technology Research Center, Korea Electrotechnology Research Institute, Changwon 51543, Republic of Korea
7 shared publications- Young-Pyo Hong
Korea Research Institute of Standards and Science, Daejeon, South Korea
2 shared publications - Dong-Woo Cho
Department of Mechanical Engineering Pohang University of Science and Technology (POSTECH) Pohang Kyungbuk Republic of Korea
1 shared publication - Haedo Jeong
Graduated School of Mechanical Engineering, Pusan National University, Busan 46703, Republic of Korea
1 shared publication In-June Hwang
Electromagnetic Wave Metrology Group, Korea Research Institute of Standards and Science, Daejeon 34113, Republic of Korea
1 shared publication
Latest Publications
- 25 September 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (39) , 395304
High-performance transparent mmWave shielding films based on metasurface absorbers for automotive radar applications
As autonomous driving technologies become more prevalent, radar sensors can potentially interfere with the safety systems of surrounding vehicles. In this study, we introduce a transparent metasurface absorber (MA) with a shielding effectiveness (SE) of over 40 dB and absorption performance exceeding 90% within the 76–81 GHz range. The MA comprises a metal-mesh-shaped resonator layer, a ground layer, and a polyethylene terephthalate-based dielectric layer. The resonator layer comprises two disk-shaped patterns, each filled with an internal micromesh structure, with sizes of 1.4 mm and 0.8 mm, respectively. The ground layer is designed as a nanomesh structure covering the entire area to maximize SE. The impacts of aperture size in the mesh-shaped electrode patterns within the resonator and ground layers on the performance of the MA was evaluated. Results show that the frequency band and absorption rate are influenced by the aperture size of the resonator layer, while the optical transmittance and SE value are influenced by that of the ground layer. An absorption rate of over 90% is achieved in the 72.5–79.5 GHz frequency range, while simultaneously obtaining an SE of 45.1 dB and an optical transmittance of 84.9%. Furthermore, the frequency range is influenced by adjusting the thickness of the dielectric layer. By decreasing the dielectric layer thickness from 525 to 375 µm, the >90% absorption range shifts to the 80.1–87.7 GHz frequency range. This innovative MA can significantly enhance the stability of autonomous driving and can be applied in several fields, such as electromagnetic shielding, stealth technology, energy harvesting, and mobile communications.
- 25 September 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (39) , 395304
High-performance transparent mmWave shielding films based on metasurface absorbers for automotive radar applications
As autonomous driving technologies become more prevalent, radar sensors can potentially interfere with the safety systems of surrounding vehicles. In this study, we introduce a transparent metasurface absorber (MA) with a shielding effectiveness (SE) of over 40 dB and absorption performance exceeding 90% within the 76–81 GHz range. The MA comprises a metal-mesh-shaped resonator layer, a ground layer, and a polyethylene terephthalate-based dielectric layer. The resonator layer comprises two disk-shaped patterns, each filled with an internal micromesh structure, with sizes of 1.4 mm and 0.8 mm, respectively. The ground layer is designed as a nanomesh structure covering the entire area to maximize SE. The impacts of aperture size in the mesh-shaped electrode patterns within the resonator and ground layers on the performance of the MA was evaluated. Results show that the frequency band and absorption rate are influenced by the aperture size of the resonator layer, while the optical transmittance and SE value are influenced by that of the ground layer. An absorption rate of over 90% is achieved in the 72.5–79.5 GHz frequency range, while simultaneously obtaining an SE of 45.1 dB and an optical transmittance of 84.9%. Furthermore, the frequency range is influenced by adjusting the thickness of the dielectric layer. By decreasing the dielectric layer thickness from 525 to 375 µm, the >90% absorption range shifts to the 80.1–87.7 GHz frequency range. This innovative MA can significantly enhance the stability of autonomous driving and can be applied in several fields, such as electromagnetic shielding, stealth technology, energy harvesting, and mobile communications.
- 21 November 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (48) , 56612-56622
Highly Transparent Ka-/W-Band Electromagnetic Shielding Films Based on Double-Layered Metal Meshes
An electromagnetic (EM) wave-shielding film exhibiting high performance in high-frequency bands, such as the Ka- and W-bands, was fabricated by using double-layered metal meshes. The double-layered shielding (DLS) film consists of metallic micromesh and nanomesh electrodes (NMEs) on the upper and lower surfaces of a poly(ethylene terephthalate) (PET) film, respectively. The micromesh electrodes (MMEs) were fabricated such that they possessed a thickness higher than the line width, and they thus exhibited excellent electromagnetic wave-shielding performance in addition to optical transmittance. Moreover, the nanomesh electrodes helped prevent the deterioration of the shielding performance owing to the increase in frequency, which was possible by decreasing the aperture size of the mesh-type electrodes. The shielding effectiveness (SE) of the double-layered metal-mesh film was evaluated by using a shielding measurement system that is optimized for high frequencies. In addition, optical transmittance and flexibility tests were conducted. The results confirm that the double-layered shielding film exhibited a shielding effectiveness of more than 50 dB at an optical transmittance of 90% and a stable bending resistance of up to 5000 cycles at a radius of curvature of 6 mm. Double-layered metal-mesh films with such excellent performance are expected to be widely used in diverse applications such as the automobile, medical, and military industries.
- 21 November 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (48) , 56612-56622
Highly Transparent Ka-/W-Band Electromagnetic Shielding Films Based on Double-Layered Metal Meshes
An electromagnetic (EM) wave-shielding film exhibiting high performance in high-frequency bands, such as the Ka- and W-bands, was fabricated by using double-layered metal meshes. The double-layered shielding (DLS) film consists of metallic micromesh and nanomesh electrodes (NMEs) on the upper and lower surfaces of a poly(ethylene terephthalate) (PET) film, respectively. The micromesh electrodes (MMEs) were fabricated such that they possessed a thickness higher than the line width, and they thus exhibited excellent electromagnetic wave-shielding performance in addition to optical transmittance. Moreover, the nanomesh electrodes helped prevent the deterioration of the shielding performance owing to the increase in frequency, which was possible by decreasing the aperture size of the mesh-type electrodes. The shielding effectiveness (SE) of the double-layered metal-mesh film was evaluated by using a shielding measurement system that is optimized for high frequencies. In addition, optical transmittance and flexibility tests were conducted. The results confirm that the double-layered shielding film exhibited a shielding effectiveness of more than 50 dB at an optical transmittance of 90% and a stable bending resistance of up to 5000 cycles at a radius of curvature of 6 mm. Double-layered metal-mesh films with such excellent performance are expected to be widely used in diverse applications such as the automobile, medical, and military industries.
- 3 February 2023
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 33 (3) , 035002
High-performance transparent electromagnetic interference shielding film based on metal meshes
Transparent electromagnetic interference (EMI) shielding films have gained considerable attention for the commercialization of the 5G wireless technology based on electromagnetic waves in the GHz range. In this study, transparent EMI shielding films with embedded metal meshes on a 100 μm thick polyethylene terephthalate film for EMI shielding were fabricated using ultraviolet imprinting and Ag paste filling techniques. The various EMI shielding film types were fabricated by varying the width, aperture size, and height of the mesh electrode to evaluate the efficiency of the EMI shielding according to the incident electromagnetic wave frequency and morphology of the mesh metallic electrodes. The results indicate that the EMI shielding efficiency (SE) increased with a decrease in the aperture size of the metal mesh electrodes and an increase in their height. The average EMI SE values of the fabricated film in the 0.5–18 GHz range reached 48.3 dB and 59.6 dB at a light transmittance of approximately 90% and 77%, respectively. The fabricated EMI shielding films can be used for various applications, such as communications, aerospace, medical equipment, and military.
- 3 February 2023
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 33 (3) , 035002
High-performance transparent electromagnetic interference shielding film based on metal meshes
Transparent electromagnetic interference (EMI) shielding films have gained considerable attention for the commercialization of the 5G wireless technology based on electromagnetic waves in the GHz range. In this study, transparent EMI shielding films with embedded metal meshes on a 100 μm thick polyethylene terephthalate film for EMI shielding were fabricated using ultraviolet imprinting and Ag paste filling techniques. The various EMI shielding film types were fabricated by varying the width, aperture size, and height of the mesh electrode to evaluate the efficiency of the EMI shielding according to the incident electromagnetic wave frequency and morphology of the mesh metallic electrodes. The results indicate that the EMI shielding efficiency (SE) increased with a decrease in the aperture size of the metal mesh electrodes and an increase in their height. The average EMI SE values of the fabricated film in the 0.5–18 GHz range reached 48.3 dB and 59.6 dB at a light transmittance of approximately 90% and 77%, respectively. The fabricated EMI shielding films can be used for various applications, such as communications, aerospace, medical equipment, and military.
- 6 May 2022
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 32 (6) , 065005
High-performance transparent heater with Ag paste-based nanomesh electrodes
Transparent heaters have attracted significant attention in recent years because of their wide range of potential applications, including defogging and defrosting windshields, thermochromic smart windows, and wearable heating devices. This paper presents a comparison of the performances of a transparent heater with nanomesh electrodes and that with micromesh electrodes. Both transparent heaters exhibit excellent basic characteristics, with an optical transmittance of more than 90%, and sheet resistance of less than 2 Ω/□. From the thermal response time tests, we observed a shorter thermal response time of 30 s for the nanomesh heater. This is because the heater must warm the transparent area; hence, the smaller transparent area of the nanomesh is more advantageous for a transparent heater. Furthermore, the nanomesh transparent heater exhibited excellent heating stability and performance at various sizes. The promising results of this study can facilitate significant and practical applications of transparent heaters, such as windshields for vehicles.
- 6 May 2022
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 32 (6) , 065005
High-performance transparent heater with Ag paste-based nanomesh electrodes
Transparent heaters have attracted significant attention in recent years because of their wide range of potential applications, including defogging and defrosting windshields, thermochromic smart windows, and wearable heating devices. This paper presents a comparison of the performances of a transparent heater with nanomesh electrodes and that with micromesh electrodes. Both transparent heaters exhibit excellent basic characteristics, with an optical transmittance of more than 90%, and sheet resistance of less than 2 Ω/□. From the thermal response time tests, we observed a shorter thermal response time of 30 s for the nanomesh heater. This is because the heater must warm the transparent area; hence, the smaller transparent area of the nanomesh is more advantageous for a transparent heater. Furthermore, the nanomesh transparent heater exhibited excellent heating stability and performance at various sizes. The promising results of this study can facilitate significant and practical applications of transparent heaters, such as windshields for vehicles.
- 29 June 2020
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 30 (9) , 095006
Fabricating transparent nanomesh-structured hydrophobic films by nanoimprinting UV-curable fluorinated polyurethane acrylates
In this work, a novel method to fabricate transparent nanomesh-structured hydrophobic (TNH) films was developed to improve the optical properties by minimizing light scattering. First, a nickel nanomesh mold was prepared using phase-shifting edge lithography. Subsequently, the TNH film was fabricated by nanoimprinting an ultraviolet-curable fluorinated polyurethane resist. The resist had a water contact angle of 93.2° when coated on a flat polyethylene terephthalate film with no pattern. Micromesh- and nanomesh-shaped patterns were applied to improve the hydrophobic property of the film. It was noted that the use of a micromesh-patterned film could improve the water contact angle to approximately 130°. Furthermore, the TNH films exhibited a water contact angle of more than 150° while maintaining a light transmittance of more than 90%. The TNH films have great potential for applications such as self-cleaning optical devices and anti-icing windows.
- 29 June 2020
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 30 (9) , 095006
Fabricating transparent nanomesh-structured hydrophobic films by nanoimprinting UV-curable fluorinated polyurethane acrylates
In this work, a novel method to fabricate transparent nanomesh-structured hydrophobic (TNH) films was developed to improve the optical properties by minimizing light scattering. First, a nickel nanomesh mold was prepared using phase-shifting edge lithography. Subsequently, the TNH film was fabricated by nanoimprinting an ultraviolet-curable fluorinated polyurethane resist. The resist had a water contact angle of 93.2° when coated on a flat polyethylene terephthalate film with no pattern. Micromesh- and nanomesh-shaped patterns were applied to improve the hydrophobic property of the film. It was noted that the use of a micromesh-patterned film could improve the water contact angle to approximately 130°. Furthermore, the TNH films exhibited a water contact angle of more than 150° while maintaining a light transmittance of more than 90%. The TNH films have great potential for applications such as self-cleaning optical devices and anti-icing windows.
- 18 September 2019
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 29 (11) , 115010
Transparent flexible heater with nano amorphous pattern
A transparent flexible heater with nano amorphous patterns (TFHAs) was fabricated using a nanofiber mask. Amorphous patterns of 600 nm, which displayed no starburst phenomenon upon illumination, were realized using conventional photolithography. The engraved Ag-paste-filled 100 mm × 100 mm conducting film achieved a transmittance of 89.9% and two-terminal resistance of 9.5 Ω, which improved to 6.4 Ω by poly(3,4-ethylenediosythiophene) (PEDOT) coating. Applying a 12 V bias, TFHAs with PEDOT achieved temperatures of 100 °C within 30 s and withstood up to 15 000 bending cycles with minimal degradation.
- 18 September 2019
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 29 (11) , 115010
Transparent flexible heater with nano amorphous pattern
A transparent flexible heater with nano amorphous patterns (TFHAs) was fabricated using a nanofiber mask. Amorphous patterns of 600 nm, which displayed no starburst phenomenon upon illumination, were realized using conventional photolithography. The engraved Ag-paste-filled 100 mm × 100 mm conducting film achieved a transmittance of 89.9% and two-terminal resistance of 9.5 Ω, which improved to 6.4 Ω by poly(3,4-ethylenediosythiophene) (PEDOT) coating. Applying a 12 V bias, TFHAs with PEDOT achieved temperatures of 100 °C within 30 s and withstood up to 15 000 bending cycles with minimal degradation.
- 28 January 2019
- Published by IOP Publishing in Nanotechnology
- Vol. 30 (12) , 125301
High-performance flexible transparent nanomesh electrodes
A cost-effective process for producing high-performance Ag-paste-based flexible transparent nanomesh electrodes (FTNEs) was developed by optimizing their linewidth, pitch, and height. These nanomesh electrodes, with a linewidth of several hundred nanometers and a pitch of 10-200 μm on a PET substrate, achieved wide ranges of transmittance (83.1%-98.8%) and sheet resistance (1.2-30.9 Ω/sq) and a figure of merit (992-1619) superior to those of indium tin oxide and silver nanowire (AgNW) electrodes. Our evaluation of their flexibility (testing up to 50 000 cycles) and their electromagnetic interference shielding effectiveness verifies the applicability of these FTNEs to various flexible optoelectronic devices.
- 28 January 2019
- Published by IOP Publishing in Nanotechnology
- Vol. 30 (12) , 125301
High-performance flexible transparent nanomesh electrodes
A cost-effective process for producing high-performance Ag-paste-based flexible transparent nanomesh electrodes (FTNEs) was developed by optimizing their linewidth, pitch, and height. These nanomesh electrodes, with a linewidth of several hundred nanometers and a pitch of 10-200 μm on a PET substrate, achieved wide ranges of transmittance (83.1%-98.8%) and sheet resistance (1.2-30.9 Ω/sq) and a figure of merit (992-1619) superior to those of indium tin oxide and silver nanowire (AgNW) electrodes. Our evaluation of their flexibility (testing up to 50 000 cycles) and their electromagnetic interference shielding effectiveness verifies the applicability of these FTNEs to various flexible optoelectronic devices.
- 21 September 2017
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 27 (10) , 105019
Ag paste-based nanomesh electrodes for large-area touch screen panels
This study reports a novel method for fabricating a nickel nanomesh mold using phase shift lithography, suitable for use in large-area touch screen panel applications. Generally, the values of light transmittance and sheet resistance of metal mesh transparent conducting electrode (TCE) films are determined by the ratio of the aperture to metal areas. In this study, taking into consideration the optimal light transmittance, sheet resistance, and pattern visibility issues, the line width of the metal mesh pattern was ~1 µ m, and the pitch of the pattern was ~100 µ m. In addition, a novel method of manufacturing wiring electrodes using a phase shift lithography process was also developed and evaluated. A TCE film with a size of 370 mm × 470 mm was prepared and evaluated for its light transmittance and sheet resistance. In addition, wiring electrodes with a length of 70 mm were fabricated and their line resistances evaluated by varying their line width.
- 21 September 2017
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 27 (10) , 105019
Ag paste-based nanomesh electrodes for large-area touch screen panels
This study reports a novel method for fabricating a nickel nanomesh mold using phase shift lithography, suitable for use in large-area touch screen panel applications. Generally, the values of light transmittance and sheet resistance of metal mesh transparent conducting electrode (TCE) films are determined by the ratio of the aperture to metal areas. In this study, taking into consideration the optimal light transmittance, sheet resistance, and pattern visibility issues, the line width of the metal mesh pattern was ~1 µ m, and the pitch of the pattern was ~100 µ m. In addition, a novel method of manufacturing wiring electrodes using a phase shift lithography process was also developed and evaluated. A TCE film with a size of 370 mm × 470 mm was prepared and evaluated for its light transmittance and sheet resistance. In addition, wiring electrodes with a length of 70 mm were fabricated and their line resistances evaluated by varying their line width.
- 1 February 2004
- Published by Elsevier in International Journal of Machine Tools and Manufacture
- Vol. 44 (2-3) , 147-154
A study on microreplication of real 3D-shape structures using elastomeric mold: from pure epoxy to composite based on epoxy
- 1 February 2004
- Published by Elsevier in International Journal of Machine Tools and Manufacture
- Vol. 44 (2-3) , 147-154
A study on microreplication of real 3D-shape structures using elastomeric mold: from pure epoxy to composite based on epoxy