FRFilippo Rubechini

Filippo Rubechini

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Filippo Rubechini has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Improving Steady Computational Fluid Dynamics to Capture the Effects of Radial Mixing in Axial Compressors

    by Lorenzo Cozzi, Filippo Rubechini, Andrea Arnone, Andrea Schneider, Pio Astrua

    The compressors of power-generation gas turbines (GTs) have a high stage count, blades with low aspect ratios, and large clearances. These features promote strong secondary flows. An important outcome deriving from the convection of intense secondary flows is the enhanced span-wise transport of fluid properties mainly involving the rear stages, generally referred to as “radial mixing.” An incorrect prediction of this key phenomenon may result in inaccurate performance evaluation and could mislead designers. In the rear compressor stages, the stream-wise vorticity associated with tip clearance flows is one of the main drivers of the span-wise transport phenomenon. Limiting it by averaging the flow at row interfaces is the reason why a steady analysis underpredicts radial mixing. To properly forecast the span-wise transport, an unsteady analysis should be adopted. However, this approach has a computational cost not yet suitable for industrial purposes. Currently, only the steady simulation can fit in a lean design chain and any model upgrade improving its radial mixing prediction would be highly beneficial. To attain some progresses in Reynolds-averaged Navier–Stokes (RANS) model, its lack of convection of stream-wise vorticity must be addressed. This can be done by acting on another mixing driver that is turbulent diffusion; by enhancing turbulent viscosity, one can promote span-wise diffusion, thus improving the radial mixing prediction. In this paper, this strategy to update the RANS model and its application on an existing compressor is presented, together with the model tuning that has been performed using unsteady results as the target.


  • Open Access

    Reducing Secondary Flow Losses in Low-Pressure Turbines: The “Snaked” Blade

    by Matteo Giovannini, Filippo Rubechini, Michele Marconcini, Andrea Arnone, Francesco Bertini

    This paper presents an innovative design for reducing the impact of secondary flows on the aerodynamics of low-pressure turbine (LPT) stages. Starting from a state-of-the-art LPT stage, a local reshaping of the stator blade was introduced in the end-wall region in order to oppose the flow turning deviation. This resulted in an optimal stator shape, able to provide a more uniform exit flow angle. The detailed comparison between the baseline stator and the redesigned one allowed for pointing out that the rotor row performance increased thanks to the more uniform inlet flow, while the stator losses were not significantly affected. Moreover, it was possible to derive some design rules and to devise a general blade shape, named ‘snaked’, able to ensure such results. This generalization translated in an effective parametric description of the ‘snaked’ shape, in which few parameters are sufficient to describe the optimal shape modification starting from a conventional design. The “snaked” blade concept and its design have been patented by Avio Aero. The stator redesign was then applied to a whole LPT module in order to evaluate the potential benefit of the ‘snaked’ design on the overall turbine performance. Finally, the design was validated by means of an experimental campaign concerning the stator blade. The spanwise distributions of the flow angle and pressure loss coefficient at the stator exit proved the effectiveness of the redesign in providing a more uniform flow to the successive row, while preserving the original stator losses.


  • Secondary Flows in Low-Pressure Turbines Cascades: Numerical and Experimental Investigation of the Impact of the Inner Part of the Boundary Layer

    by Matteo Giovannini, Filippo Rubechini, Michele Marconcini, Daniele Simoni, Vianney Yepmo, Francesco Bertini

    Due to the low level of profile losses reached in low-pressure turbines (LPT) for turbofan applications, a renewed interest is devoted to other sources of loss, e.g., secondary losses. At the same time, the adoption of high-lift profiles has reinforced the importance of these losses. A great attention, therefore, is dedicated to reliable prediction methods and to the understanding of the mechanisms that drive the secondary flows. In this context, a numerical and experimental campaign on a state-of-the-art LPT cascade was carried out focusing on the impact of different inlet boundary layer (BL) profiles. First of all, detailed Reynolds Averaged Navier-Stokes (RANS) analyzes were carried out in order to establish dependable guidelines for the computational setup. Such analyzes also underlined the importance of the shape of the inlet BL very close to the endwall, suggesting tight requirements for the characterization of the experimental environment. The impact of the inlet BL on the secondary flow was experimentally investigated by varying the inlet profile very close to the endwall as well as on the external part of the BL. The effects on the cascade performance were evaluated by measuring the span-wise distributions of flow angle and total pressure losses. For all the inlet conditions, comparisons between Computational Fluid Dynamics (CFD) and experimental results are discussed. Besides providing guidelines for a proper numerical and experimental setup, the present paper underlines the importance of a detailed characterization of the inlet BL for an accurate assessment of the secondary flows.