KMKonrad Malicki

Konrad Malicki

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Konrad Malicki has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Edge Zone Effect in Measurements of Asphalt Mixture Thermal Properties Using Transient Method

    by Jarosław Górszczyk, Konrad Malicki

    Thermal conductivity and specific heat capacity are key parameters controlling heat transfer and temperature distribution in road pavement structures. Although transient methods are increasingly used in laboratory testing, the thermal properties of asphalt mixtures have not been sufficiently studied using these methods, and no dedicated standards exist for road materials. This creates uncertainty in test procedures, specimen geometry, surface preparation, measurement location, and data interpretation, which may lead to significant errors, especially for massive and heterogeneous mixtures. The objective of this study is to systematically quantify the edge zone effect and assess its influence on the determined thermal parameters of a selected heterogeneous asphalt mixture. The study focuses on the quantitative determination of the edge zone effect, practical identification of its width in slab-shaped specimen, and the identification of scientific and practical methodological consequences, as well as the risks and limitations of applying the Modified Transient Plane Source (MTPS) method in the absence of standards. Laboratory measurements demonstrate a clear edge zone effect, with thermal conductivity and thermal diffusivity differing by up to 17% and 18%, respectively, near the specimen edges. These findings highlight the importance of methodological guidelines for slab-shaped asphalt mixture specimens and provide both scientific insight and practical guidance for the reliable application of transient method. They may also support the development of standardized testing procedures for asphalt mixtures.

  • Open Access

    Comparative Laboratory Tests of Thermal Conductivity of Road Materials Using Two Measurement Methods

    by Jarosław Górszczyk, Konrad Malicki

    The fundamental material parameter used in the thermal analysis of road pavement structures is the thermal conductivity. This parameter can be determined using various methods. The main objective of this paper is to compare and evaluate the thermal conductivity test results obtained using two different measurement methods. Thermal conductivity was determined using the steady-state and transient methods. The transient method is more cost-effective and faster but tends to produce a higher dispersion of results. In contrast, the steady-state method is more challenging to apply, particularly when testing large and heavy specimens of heterogeneous materials such as road pavement materials. For this reason, it is essential to assess the differences in results obtained by these two methods when applied to road materials. Two types of materials were tested in this study: an asphalt mixture and a cement concrete. The obtained results show statistically significant differences (α = 0.05), taking into account the two methods considered. The average difference can be estimated at 10% and 11% for asphalt mixtures and cement concretes, respectively. The obtained results are important for quantifying material parameters used in thermal and coupled thermal/structural analysis of pavement structures. This is particularly relevant in areas affected by urban heat islands and in road sections used as solar collectors.


  • Open Access

    Laboratory Investigation on Dynamic Complex Modulus of FRPU Composite

    by Jarosław Górszczyk, Konrad Malicki, Arkadiusz Kwiecień

    Civil engineering structures are subject to both static and dynamic loadings. This applies especially to buildings in seismic areas as well as bridges, viaducts, and road and railway structures loaded with road or rail traffic. One of the solutions used to repair and strengthen such structures in the event of emergency damage are fibre-reinforced polyurethanes (FRPUs). The article proposes a laboratory method for determining the dynamic complex modulus of FRPU composite tape. The theoretical basis for determining the complex modulus for the tested material is presented. Laboratory tests were carried out using the tensile method for four cyclic loading frequencies and a cyclic load ratio equal to 0.5. Under the assumed test conditions, the material showed a viscoelastic performance with a dominant elastic part (storage modulus). For a frequency of 0.1 Hz, the viscous part (loss modulus) was about 8% of the storage modulus value, while for a frequency of 10 Hz, this value was about 5%. For a loading frequency of 0.1 Hz, the elastic part of the complex modulus was about 1160 MPa, while for a frequency of 10 Hz, it was about 1790 MPa. With the increase in loading frequency, the absolute value of the complex modulus increased.

  • Open Access

    Bezkontaktowa metoda pomiaru deformacji w badaniach wybranych materiałów stosowanych w budownictwie drogowym

    by Jarosław Górszczyk, Konrad Malicki

    Wysokie wymagania stawiane materiałom stosowanym w budownictwie drogowym powodują konieczność stosowania nowoczesnych metod oceny ich parametrów mechanicznych. Jedną z takich metod jest metoda cyfrowej korelacji obrazu (Digital Image Correlation – DIC). W artykule zaprezentowano możliwości wykorzystania bezkontaktowej metody DIC do pomiaru deformacji w badaniach wybranych cech mechanicznych próbek mieszanki mineralno-asfaltowej oraz kompozytu wykonanego z matrycy polimerowej zbrojonej siatką z włókien szklanych – (fiber reinforced polimer – FRP). W pracy pokazano analizy deformacji całych obserwowanych powierzchni badanych próbek. Stwierdzono też, że pod względem wytrzymałości statycznej na rozciąganie praca taśmy FRP jest podobna do zachowania geosiatek stosowanych do wzmacniania konstrukcji nawierzchni drogowych. Omówione wyniki badań własnych oraz badań opisanych w literaturze potwierdziły przydatność metody DIC w badaniach materiałów stosowanych w inżynierii lądowej.

  • Open Access

    Recycled Polyester Geosynthetic Influence on Improvement of Road and Railway Subgrade Bearing Capacity— Laboratory Investigations

    by Konrad Malicki, Jarosław Górszczyk, Zuzana Dimitrovová

    After years of using geosynthetics in civil engineering and infrastructure construction, it has recently become necessary to consider the possibility of recycling and reusing these materials. This paper presents the results of laboratory tests of the effect of recycled geogrid on the bearing capacity of soils using a CBR test. A polyester geosynthetic was selected for testing due to its high resistance to biodegradation and wide application. In a series of laboratory tests, two types of road and railway subgrade were used, mixed with geosynthetic cuttings in two different weight concentrations. The aim of the research was to demonstrate whether old demolition geosynthetics could be used to strengthen road and rail subgrade as recycled material. The influence of the geosynthetic cutting shape was also considered. The obtained results confirm the possibility of using recycled geogrid to improve the bearing capacity of the pavement subgrade, at least under these laboratory conditions. In the case of sand, the use of 2.0% additive causes that the poorly compacted soil obtains sufficient bearing capacity for the layer of road improved subgrade. As expected, the level of this improvement depends on the type of soil and the shape of geogrid cuttings.


  • Open Access

    The Effect of Fatigue Test on the Mechanical Properties of the Cellular Polyurethane Mats Used in Tram and Railway Tracks

    by Juliusz Sołkowski, Jarosław Górszczyk, Konrad Malicki, Dariusz Kudła

    The use of modern synthetic materials is an important element in the development of railway tracks. Their use is a response to the growing requirements regarding the durability of structures and environmental protection against traffic noise and vibrations. In this paper, the results of the laboratory tests of selected mechanical properties of cellular polyurethane (PUR) mats which are applied in tram and railway tracks are presented in this study. The aim of the research was to determine the effect of fatigue loading on the mechanical performance of polyurethane mats. A series of samples made of two types of materials with different pore structures were tested. Static and fatigue laboratory tests were carried out on a specially prepared test stand. The values of selected mechanical parameters (the vertical static bedding modulus, the vertical dynamic bedding modulus, and the loss factor) were evaluated. The results of laboratory tests and analyses showed a significant influence of high-cycle fatigue loading on the values of mechanical parameters of the tested mats, which were quantified as a result of the study. For both types of materials, the phenomenon of cyclic hardening was observed. Additionally, for one of the materials, an undesired dynamic creep phenomenon was observed. It was also shown that the pore structure of polyurethane influences the mechanical performance of the mats. Therefore, the findings of the research may have practical significance for the quality evaluation of such materials, especially in the context of their durability and mechanical stability under real loading conditions.


  • Open Access

    Application of Digital Image Correlation (DIC) Method for Road Material Testing

    by Jarosław Górszczyk, Konrad Malicki, Teresa Zych

    The theoretical part of the paper presents the framework of the digital image correlation (DIC) method as well as its advantages and limitations. The DIC technique that can be used in static and fatigue tests is a non-contact, non-interferometric optical method for measuring the surface deformation of structural elements, and material samples. In the experimental part of the paper, the implementation of the DIC method for the selected laboratory tests of building materials is described. The results of the tests on the samples of the materials used in road construction, i.e., asphalt mixtures (HMA), stone, soil stabilized with a hydraulic binder, and geosynthetics are discussed. The conducted research pointed out the possibilities of using the DIC method to evaluate the deformation of road materials in laboratory tests, taking into account their specificity. The variety of samples of tested material allowed to indicate the areas in which the DIC method and the algorithms used to evaluate the results give a significant advantage compared to tensometric measurement methods.