Baptiste Flipon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Baptiste Flipon has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Marc Bernacki
PSL University Centre for material forming (CEMEF) Mines Paris UMR CNRS 06904 Sophia Antipolis France
12 shared publications - Nathalie Bozzolo
MINES ParisTech, PSL Research University, CEMEF - Centre de mise en forme des matériaux, CNRS, UMR 7635, Sophia Antipolis Cedex, France
5 shared publications C. Keller
4 shared publications- Fabrice Barbe
Normandie Université, University of Rouen, INSA Rouen
4 shared publications - Victor Grand
Components Research Center, Framatome 73403 Ugine, France
4 shared publications - Alexis Gaillac
Framatome—Components Research Center, 73403 Ugine, France
3 shared publications
Latest Publications
- Open Access
- 14 August 2026
- Published by Elsevier in SSRN Electronic Journal
Continuous Dynamic Recrystallization in Hot-Deformed AA2139 Aluminium Alloy: Influence of Thermomechanical Conditions and Crystallographic Orientation
Despite the well-established terminology used to distinguish continuous, discontinuous,and geometric dynamic recrystallization (CDRX, DDRX, and GDRX), the occurrenceand identification of DRX mechanisms in high-stacking-fault-energy materials, includingaluminium alloys, is still debated. This ambiguity limits the development of physicallybased models, especially regarding the origin of fine equiaxed grains fully enclosed byhigh-angle grain boundaries (HAGBs). In this work, the DRX behaviour of AA2139 aluminiumalloy was investigated during hot compression under various thermomechanicalconditions. Electron Backscatter Diffraction (EBSD) analyses were used to quantify lowanglegrain boundaries (LAGBs), HAGBs, geometrically necessary dislocations (GNDs),recrystallized grains, and texture. The results indicate that CDRX is the main activemechanism under the investigated conditions. This is supported by the progressive increasein LAGB disorientation, the higher fraction of 10-15° LAGBs, and the increase inHAGBs within the 15-35° range, which are consistent with the gradual transformation ofLAGBs into HAGBs. In contrast, GDRX remains limited, since 99.5% of the deformedmicrostructure remains too thick to satisfy the geometrical pinch-off condition. The kineticsof CDRX also vary with thermomechanical conditions: increasing strain and strainrate promote LAGB-to-HAGB transformation, while increasing temperature favours recrystallization through enhanced dislocation and grain boundary mobility. Finally, CDRXis orientation-dependent, with Near Cube grains developing denser LAGB networks andcontributing preferentially to the recrystallized grain population. These results providequantitative evidence for CDRX and highlight the need to include local crystallographicorientation in physically based models for hot deformation of aluminium alloys.
- 14 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessContinuous Dynamic Recrystallization in Hot-Deformed AA2139 Aluminium Alloy: Influence of Thermomechanical Conditions and Crystallographic Orientation
Despite the well-established terminology used to distinguish continuous, discontinuous,and geometric dynamic recrystallization (CDRX, DDRX, and GDRX), the occurrenceand identification of DRX mechanisms in high-stacking-fault-energy materials, includingaluminium alloys, is still debated. This ambiguity limits the development of physicallybased models, especially regarding the origin of fine equiaxed grains fully enclosed byhigh-angle grain boundaries (HAGBs). In this work, the DRX behaviour of AA2139 aluminiumalloy was investigated during hot compression under various thermomechanicalconditions. Electron Backscatter Diffraction (EBSD) analyses were used to quantify lowanglegrain boundaries (LAGBs), HAGBs, geometrically necessary dislocations (GNDs),recrystallized grains, and texture. The results indicate that CDRX is the main activemechanism under the investigated conditions. This is supported by the progressive increasein LAGB disorientation, the higher fraction of 10-15° LAGBs, and the increase inHAGBs within the 15-35° range, which are consistent with the gradual transformation ofLAGBs into HAGBs. In contrast, GDRX remains limited, since 99.5% of the deformedmicrostructure remains too thick to satisfy the geometrical pinch-off condition. The kineticsof CDRX also vary with thermomechanical conditions: increasing strain and strainrate promote LAGB-to-HAGB transformation, while increasing temperature favours recrystallization through enhanced dislocation and grain boundary mobility. Finally, CDRXis orientation-dependent, with Near Cube grains developing denser LAGB networks andcontributing preferentially to the recrystallized grain population. These results providequantitative evidence for CDRX and highlight the need to include local crystallographicorientation in physically based models for hot deformation of aluminium alloys.
- Open Access
- 23 April 2026
- Published by Elsevier in Acta Materialia
- Vol. 312
InfinityEBSD : Metrics-guided infinite-size EBSD map generation with diffusion models
- 23 April 2026
- Published by Elsevier in Acta Materialia
- Vol. 312
Open AccessInfinityEBSD : Metrics-guided infinite-size EBSD map generation with diffusion models
- 3 April 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Alliages à grains ultrafins et bimodaux : approche couplée expérience-modélisation basée sur la microstructure
Ce travail porte sur l'élaboration et l'analyse du comportement mécanique d'alliages à distribution bimodale de taille de grains. Les applications concernent les aciers inoxydables austénitiques 304L et 316L. Une approche couplée expérience-modélisation est menée pour comprendre les réponses mécaniques macroscopiques et locales de ces nouveaux alliages en se basant notamment sur l'étude des mécanismes de déformation associés. L'utilisation de deux voies d'élaboration et l'optimisation de leurs paramètres a conduit à l'obtention d'un large choix d'échantillons avec différentes distributions bimodales et différentes proportions de chaque famille de taille de grains. L'influence de ces caractéristiques microstructurales sur le comportement a été analysée sur la base d'essais en traction simple sous chargement monotone ou en charges-décharges alternées. Une base de données étendue de propriétés a ainsi été constituée et des éléments de réponse concernant les mécanismes de déformation propres aux alliages bimodaux ont pu être apportés. La présence de grains de taille conventionnelle (Coarse Grain -CG) au sein d'une matrice à grains ultrafins (UltraFine Grain - UFG) semble favoriser la relaxation d'une partie des contraintes internes de la matrice et tend ainsi à retarder l'endommagement des alliages bimodaux en comparaison aux alliages unimodaux à grains ultrafins. Une modélisation à champs complets selon deux lois de plasticité cristalline tenant compte explicitement d'une longueur interne a été proposée. Sa première motivation est de fournir un outil de prédiction du comportement effectif des alliages bimodaux en fonction de leurs caractéristiques microstructurales. Elle donne par ailleurs accès aux champs locaux et permet d'appuyer les analyses expérimentales en partition des contraintes en montrant à la fois une relaxation partielle des contraintes dans la matrice UFG mais aussi des concentrations de contrainte aux interfaces CG/UFG.
- 3 April 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Alliages à grains ultrafins et bimodaux : approche couplée expérience-modélisation basée sur la microstructure
Ce travail porte sur l'élaboration et l'analyse du comportement mécanique d'alliages à distribution bimodale de taille de grains. Les applications concernent les aciers inoxydables austénitiques 304L et 316L. Une approche couplée expérience-modélisation est menée pour comprendre les réponses mécaniques macroscopiques et locales de ces nouveaux alliages en se basant notamment sur l'étude des mécanismes de déformation associés. L'utilisation de deux voies d'élaboration et l'optimisation de leurs paramètres a conduit à l'obtention d'un large choix d'échantillons avec différentes distributions bimodales et différentes proportions de chaque famille de taille de grains. L'influence de ces caractéristiques microstructurales sur le comportement a été analysée sur la base d'essais en traction simple sous chargement monotone ou en charges-décharges alternées. Une base de données étendue de propriétés a ainsi été constituée et des éléments de réponse concernant les mécanismes de déformation propres aux alliages bimodaux ont pu être apportés. La présence de grains de taille conventionnelle (Coarse Grain -CG) au sein d'une matrice à grains ultrafins (UltraFine Grain - UFG) semble favoriser la relaxation d'une partie des contraintes internes de la matrice et tend ainsi à retarder l'endommagement des alliages bimodaux en comparaison aux alliages unimodaux à grains ultrafins. Une modélisation à champs complets selon deux lois de plasticité cristalline tenant compte explicitement d'une longueur interne a été proposée. Sa première motivation est de fournir un outil de prédiction du comportement effectif des alliages bimodaux en fonction de leurs caractéristiques microstructurales. Elle donne par ailleurs accès aux champs locaux et permet d'appuyer les analyses expérimentales en partition des contraintes en montrant à la fois une relaxation partielle des contraintes dans la matrice UFG mais aussi des concentrations de contrainte aux interfaces CG/UFG.
- Top Cited PapersOpen Access
- 16 January 2026
- Published by Elsevier in Acta Materialia
- Vol. 306
Characterization and modeling of continuous dynamic recrystallization (CDRX): Application to 2139 aluminum alloy
- 16 January 2026
- Published by Elsevier in Acta Materialia
- Vol. 306
Top Cited PapersOpen AccessCharacterization and modeling of continuous dynamic recrystallization (CDRX): Application to 2139 aluminum alloy
- Open Access
Comparison of Grain-Growth Mean-Field Models Regarding Predicted Grain Size Distributions
Mean-field models have the ability to predict the evolution of grain size distribution that occurs through thermomechanical solicitations. This article focuses on a comparison of mean-field models under grain-growth conditions. Different microstructure representations are considered and discussed, especially regarding the consideration of topology in the neighborhood construction. Experimental data obtained with a heat treatment campaign on 316L austenitic stainless steel are used for the identification of material parameters and as a reference for model comparisons. Mean-field models are also applied to both mono- and bimodal initial grain size distributions to investigate the potential benefits of introducing neighborhood topology in microstructure prediction models. This article demonstrates that improvements in the predictions can be obtained in monomodal cases for topological models. In the bimodal test, no comparison with experimental data was performed as no data were available. But relative comparisons between models indicated few differences in the predictions. Although of interest, the consideration of neighborhood topology in grain-growth mean-field models generally results in only small improvements compared to classical mean-field models, especially in terms of implementation complexity.
Open AccessComparison of Grain-Growth Mean-Field Models Regarding Predicted Grain Size Distributions
Mean-field models have the ability to predict the evolution of grain size distribution that occurs through thermomechanical solicitations. This article focuses on a comparison of mean-field models under grain-growth conditions. Different microstructure representations are considered and discussed, especially regarding the consideration of topology in the neighborhood construction. Experimental data obtained with a heat treatment campaign on 316L austenitic stainless steel are used for the identification of material parameters and as a reference for model comparisons. Mean-field models are also applied to both mono- and bimodal initial grain size distributions to investigate the potential benefits of introducing neighborhood topology in microstructure prediction models. This article demonstrates that improvements in the predictions can be obtained in monomodal cases for topological models. In the bimodal test, no comparison with experimental data was performed as no data were available. But relative comparisons between models indicated few differences in the predictions. Although of interest, the consideration of neighborhood topology in grain-growth mean-field models generally results in only small improvements compared to classical mean-field models, especially in terms of implementation complexity.
- 13 October 2023
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 31 (8) , 085008
Modeling CDRX and MDRX during hot forming of zircaloy-4
A recently developed full field level-set model of continuous dynamic recrystallization is applied to simulate zircaloy-4 recrystallization during hot compression and subsequent heat treatment. The influence of strain rate, final strain and initial microstructure is investigated, by experimental and simulation tools. The recrystallization heterogeneity is quantified. This enables to confirm that quenched microstructures display a higher extent of heterogeneity. The simulation results replicate satisfactorily experimental observations. The simulation framework is especially able to capture such recrystallization heterogeneity induced by a different initial microstructure. Finally, the role of intragranular dislocation density heterogeneities over the preferential growth of recrystallized grains is pointed out thanks to additional simulations with different numerical formulations.
- 13 October 2023
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 31 (8) , 085008
Modeling CDRX and MDRX during hot forming of zircaloy-4
A recently developed full field level-set model of continuous dynamic recrystallization is applied to simulate zircaloy-4 recrystallization during hot compression and subsequent heat treatment. The influence of strain rate, final strain and initial microstructure is investigated, by experimental and simulation tools. The recrystallization heterogeneity is quantified. This enables to confirm that quenched microstructures display a higher extent of heterogeneity. The simulation results replicate satisfactorily experimental observations. The simulation framework is especially able to capture such recrystallization heterogeneity induced by a different initial microstructure. Finally, the role of intragranular dislocation density heterogeneities over the preferential growth of recrystallized grains is pointed out thanks to additional simulations with different numerical formulations.
- Open Access
Comparison of grain growth mean-field models regarding predicted grain size distributions
Mean-field models have the ability to predict grain size distribution evolution occurring through thermomechanical solicitations. This article focuses on a comparison of mean-field models under grain growth conditions. Different microstructure representations are considered and discussed, especially regarding the consideration of topology in the neighborhood construction. Experimental data obtained with a heat treatment campaign on a 316L austenitic stainless steel are used for material parameters identification and as a reference for model comparisons. Mean-field models are also confronted to both mono- and bimodal initial grain size distributions to investigate the interest of introducing neighborhood topology in microstructure predictions models. This article exposes that improvements in the predictions are obtained in monomodal cases for topological models. In bimodal test, no comparison with experimental data were performed as no data were available. But relative comparisons between models indicate few differences in predictions. The interest of neighborhood topology in grain growth mean-field models gives overall small improvements compared to classical mean-field models when comparing implementation complexity.
Open AccessComparison of grain growth mean-field models regarding predicted grain size distributions
Mean-field models have the ability to predict grain size distribution evolution occurring through thermomechanical solicitations. This article focuses on a comparison of mean-field models under grain growth conditions. Different microstructure representations are considered and discussed, especially regarding the consideration of topology in the neighborhood construction. Experimental data obtained with a heat treatment campaign on a 316L austenitic stainless steel are used for material parameters identification and as a reference for model comparisons. Mean-field models are also confronted to both mono- and bimodal initial grain size distributions to investigate the interest of introducing neighborhood topology in microstructure predictions models. This article exposes that improvements in the predictions are obtained in monomodal cases for topological models. In bimodal test, no comparison with experimental data were performed as no data were available. But relative comparisons between models indicate few differences in predictions. The interest of neighborhood topology in grain growth mean-field models gives overall small improvements compared to classical mean-field models when comparing implementation complexity.
- 29 August 2023
- Published by Springer Nature
- p. 611-622
From the Industrial Use of Digital Microstructures in the Context of Hot Metal Forming Processes: A Reality in Motion
- 29 August 2023
- Published by Springer Nature
- p. 611-622
From the Industrial Use of Digital Microstructures in the Context of Hot Metal Forming Processes: A Reality in Motion
- Open Access
Modeling CDRX and PDRX during hot forming of zircaloy-4
A recently developed full field level-set model of continuous dynamic recrystallization is applied to simulate zircaloy-4 recrystallization during hot compression and subsequent heat treatment. The influence of strain rate, final strain and initial microstructure is investigated, by experimental and simulation tools. The recrystallization heterogeneity is quantified. This enables to confirm that quenched microstructures display a higher extent of heterogeneity. The simulation results replicate satisfactorily experimental observations. The simulation framework is especially able to capture such recrystallization heterogeneity induced by a different initial microstructure. Finally, the role of intragranular dislocation density heterogeneities over the preferential growth of recrystallized grains is pointed out thanks to additional simulations with different numerical formulations.
Open AccessModeling CDRX and PDRX during hot forming of zircaloy-4
A recently developed full field level-set model of continuous dynamic recrystallization is applied to simulate zircaloy-4 recrystallization during hot compression and subsequent heat treatment. The influence of strain rate, final strain and initial microstructure is investigated, by experimental and simulation tools. The recrystallization heterogeneity is quantified. This enables to confirm that quenched microstructures display a higher extent of heterogeneity. The simulation results replicate satisfactorily experimental observations. The simulation framework is especially able to capture such recrystallization heterogeneity induced by a different initial microstructure. Finally, the role of intragranular dislocation density heterogeneities over the preferential growth of recrystallized grains is pointed out thanks to additional simulations with different numerical formulations.
- Open Access
Simulation of Continuous Dynamic Recrystallization Using a Level-Set Method
Dynamic recrystallization is one of the main phenomena responsible for microstructure evolution during hot forming. Consequently, obtaining a better understanding of dynamic recrystallization mechanisms and being able to predict them is crucial. This paper proposes a full-field numerical framework to predict the evolution of subgrain structures upon grain growth, continuous dynamic recrystallization, and post-dynamic recrystallization. To be able to consider a subgrain structure, two strategies are proposed. One relies on a two-step tessellation algorithm to generate a fully substructured microstructure. The second strategy enables for the simulation of the formation of new subgrains during hot deformation. Using these tools, the grain growth of a fully substructured microstructure is modeled. The influence of microstructure topology, subgrain parameters, and some remaining stored energy due to plastic deformation is discussed. The results highlight that the selective growth of a limited number of subgrains is observed only when mobility is a sigmoidal function of disorientation. The recrystallization kinetics predicted with different criteria for discrimination of recrystallized grains are quantitatively compared. Finally, the ability of the framework to model continuous dynamic and post-dynamic recrystallization is assessed upon a case study representative of the hot extrusion of a zircaloy-4 billet ( °C). The influence of grain boundary properties and nucleation rules are quantified to evaluate the model sensitivity and suitability. Application of these numerical tools to other thermomechanical conditions and microstructures will be presented in an upcoming article.Open AccessSimulation of Continuous Dynamic Recrystallization Using a Level-Set Method
Dynamic recrystallization is one of the main phenomena responsible for microstructure evolution during hot forming. Consequently, obtaining a better understanding of dynamic recrystallization mechanisms and being able to predict them is crucial. This paper proposes a full-field numerical framework to predict the evolution of subgrain structures upon grain growth, continuous dynamic recrystallization, and post-dynamic recrystallization. To be able to consider a subgrain structure, two strategies are proposed. One relies on a two-step tessellation algorithm to generate a fully substructured microstructure. The second strategy enables for the simulation of the formation of new subgrains during hot deformation. Using these tools, the grain growth of a fully substructured microstructure is modeled. The influence of microstructure topology, subgrain parameters, and some remaining stored energy due to plastic deformation is discussed. The results highlight that the selective growth of a limited number of subgrains is observed only when mobility is a sigmoidal function of disorientation. The recrystallization kinetics predicted with different criteria for discrimination of recrystallized grains are quantitatively compared. Finally, the ability of the framework to model continuous dynamic and post-dynamic recrystallization is assessed upon a case study representative of the hot extrusion of a zircaloy-4 billet ( °C). The influence of grain boundary properties and nucleation rules are quantified to evaluate the model sensitivity and suitability. Application of these numerical tools to other thermomechanical conditions and microstructures will be presented in an upcoming article.