Yun Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yun Wang has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Jing Shi
Department of Mechanical, Materials, and Industrial Engineering, College of Engineering and Applied Science, University of Cincinnati, Cincinnati, USA
3 shared publications - Yachao Wang
Department of Mechanical and Materials Engineering, College of Engineering and Applied Science, University of Cincinnati, Cincinnati, OH 45221
3 shared publications Prashant Kumar
2 shared publications- Shuai Xu
College of Engineering and Mines
2 shared publications Shuo Yin
2 shared publications- Xiaodong Hou
Univ. of North Dakota, Grand Forks, ND (United States)
2 shared publications
Latest Publications
- Open Access
Research on a Novel Trailing-Edge Winglet with Passive Automatic Angle-of-Attack Adjustment Function
Low-altitude general aviation aircraft and unmanned aerial vehicles (UAVs) are widely deployed for complex operational tasks, yet low-altitude gusts and crosswind disturbances induce severe airspeed fluctuations, leading to variable lift, unstable flight altitude, and perturbed pitch attitude. Such aerodynamic fluctuations degrade flight smoothness and increase pilot control workload. To mitigate lift and altitude instability under unsteady incoming flow, this paper proposes a novel passive trailing-edge winglet configuration capable of self-regulating wing angle of attack (AOA) without active flight control systems. A quasi-static aerodynamic equilibrium analytical model based on moment balance about the wing pivot axis is established, combined with validated Computational Fluid Dynamics (CFD) simulations to characterize the passive AOA adjustment mechanism and quantify lift variations under velocity perturbations. Results demonstrate that the integrated wing-winglet layout generates passive aerodynamic feedback moments to automatically adjust the wing AOA when freestream speed varies. For airspeed disturbances within ±10% of the cruise velocity (102 m/s, 0.3 Ma), the total lift fluctuation of the wing-winglet assembly is suppressed within ±1.01%, whereas conventional fixed-wing configurations experience lift deviations between −16% and +22% under identical disturbance conditions. Notably, the present study only verifies quasi-static aerodynamic equilibrium under steady inflow; dynamic flight stability, unsteady aerodynamic effects, and stall-limit performance remain unexamined and require further investigation. The core novelty of this design lies in the passive negative-feedback aerodynamic moment generated by the trailing-edge winglet, which decouples fuselage attitude from wing pitching motion and stabilizes equilibrium lift under mild low-altitude gust perturbations.
Open AccessResearch on a Novel Trailing-Edge Winglet with Passive Automatic Angle-of-Attack Adjustment Function
Low-altitude general aviation aircraft and unmanned aerial vehicles (UAVs) are widely deployed for complex operational tasks, yet low-altitude gusts and crosswind disturbances induce severe airspeed fluctuations, leading to variable lift, unstable flight altitude, and perturbed pitch attitude. Such aerodynamic fluctuations degrade flight smoothness and increase pilot control workload. To mitigate lift and altitude instability under unsteady incoming flow, this paper proposes a novel passive trailing-edge winglet configuration capable of self-regulating wing angle of attack (AOA) without active flight control systems. A quasi-static aerodynamic equilibrium analytical model based on moment balance about the wing pivot axis is established, combined with validated Computational Fluid Dynamics (CFD) simulations to characterize the passive AOA adjustment mechanism and quantify lift variations under velocity perturbations. Results demonstrate that the integrated wing-winglet layout generates passive aerodynamic feedback moments to automatically adjust the wing AOA when freestream speed varies. For airspeed disturbances within ±10% of the cruise velocity (102 m/s, 0.3 Ma), the total lift fluctuation of the wing-winglet assembly is suppressed within ±1.01%, whereas conventional fixed-wing configurations experience lift deviations between −16% and +22% under identical disturbance conditions. Notably, the present study only verifies quasi-static aerodynamic equilibrium under steady inflow; dynamic flight stability, unsteady aerodynamic effects, and stall-limit performance remain unexamined and require further investigation. The core novelty of this design lies in the passive negative-feedback aerodynamic moment generated by the trailing-edge winglet, which decouples fuselage attitude from wing pitching motion and stabilizes equilibrium lift under mild low-altitude gust perturbations.
- Open Access
- 13 March 2026
- Published by Elsevier in SSRN Electronic Journal
Investigation on Electrochemical and Thermal Behaviors of Lithium-Ion Batteries with Laser-Structured Anodes under Ultra-Fast Charging Conditions
A three-dimensional electrochemical–thermal coupled full-cell simulation framework was developed to evaluate the performance of laser-structured graphite anodes under fast-charging conditions and validated through direct comparison with full-cell experimental data. The channeled electrode geometry was integrated into a pouch-cell configuration, in which temperature, electric potential, and lithium-ion transport fields were solved in a fully coupled manner. Cells with laser-structured and conventional anodes were comparatively studied under the fast-charging conditions of 1 C, 4 C, and 7 C. At 7 C. It was found that the laser-structured cell extended the usable SOC window before reaching the 3.65 V cutoff by approximately 16%, demonstrating improved charge acceptance under ultra-fast charging. The lithium-ion concentration gradient at 40% SOC decreased from 328.11 mol/m3 to 102.77 mol/m3, indicating substantially improved mass transport. Peak reaction current density decreased by 30.3% at 4 C and 26.6% at 7 C. Thermally, anode-side polarization heat was significantly suppressed, and peak surface temperature was reduced by 3.5 K at 7 C, with temperature non-uniformity decreasing from 1.5 K to 1.0 K. These results demonstrate that laser structuring enables coupled electrochemical–thermal regulation at the full-cell level, providing a scalable pathway toward safer and more efficient ultra-fast charging lithium-ion batteries.
- 13 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInvestigation on Electrochemical and Thermal Behaviors of Lithium-Ion Batteries with Laser-Structured Anodes under Ultra-Fast Charging Conditions
A three-dimensional electrochemical–thermal coupled full-cell simulation framework was developed to evaluate the performance of laser-structured graphite anodes under fast-charging conditions and validated through direct comparison with full-cell experimental data. The channeled electrode geometry was integrated into a pouch-cell configuration, in which temperature, electric potential, and lithium-ion transport fields were solved in a fully coupled manner. Cells with laser-structured and conventional anodes were comparatively studied under the fast-charging conditions of 1 C, 4 C, and 7 C. At 7 C. It was found that the laser-structured cell extended the usable SOC window before reaching the 3.65 V cutoff by approximately 16%, demonstrating improved charge acceptance under ultra-fast charging. The lithium-ion concentration gradient at 40% SOC decreased from 328.11 mol/m3 to 102.77 mol/m3, indicating substantially improved mass transport. Peak reaction current density decreased by 30.3% at 4 C and 26.6% at 7 C. Thermally, anode-side polarization heat was significantly suppressed, and peak surface temperature was reduced by 3.5 K at 7 C, with temperature non-uniformity decreasing from 1.5 K to 1.0 K. These results demonstrate that laser structuring enables coupled electrochemical–thermal regulation at the full-cell level, providing a scalable pathway toward safer and more efficient ultra-fast charging lithium-ion batteries.
- Open Access
Study on the Characteristics of a Composite Power System with a Tip-Jet-Driven Rotor
Tip-jet helicopters operate by utilizing the reaction force generated by a high-speed tip jet, offering advantages such as a simplified and compact fuselage design and a reduction in empty weight by eliminating anti-torque balancing equipment. In tip-jet helicopter research, the composite power system is regarded as a crucial and bottleneck element. This study employs numerical simulations to comprehensively analyze the internal flow characteristics of the gas generator and tip-jet-driven rotor within the composite power system. Specifically, an in-depth investigation has been conducted on the influence laws of various parameters on the system characteristics. These parameters encompass the tip-jet-driven rotor speed, which takes on values of 50 rad/s, 80 rad/s, 100 rad/s, 120 rad/s, and 150 rad/s, the tip-jet-driven rotor length, measured at 1585 mm, 1785 mm, 1985 mm, 2185 mm, 2385 mm, 2585 mm, and 2785 mm, and the tip-jet-driven rotor nozzle area, which is specified by six values corresponding to multiples of the straight section area of the rotor’s internal channel, namely 0.25 times, 0.5 times, 0.75 times, 1 times, 1.25 times, and 1.5 times. The analysis of the obtained results indicates several significant relationships. Firstly, it is observed that the available moment exhibits a linear decrease as the tip-jet-driven rotor speed increases. Secondly, the maximum available moment is attained when the tip-jet-driven rotor length (L) satisfies the relationship L = Vr/2ω. Additionally, the maximum available power is achieved when the transport velocity of the tip-jet-driven rotor nozzle is precisely half of the relative velocity of the nozzle. Moreover, under the condition that the mass flow rate of the tip-jet-driven rotor nozzle remains constant, a positive correlation between the available moment and the reduction in the tip-jet-driven rotor nozzle area is noted.
Open AccessStudy on the Characteristics of a Composite Power System with a Tip-Jet-Driven Rotor
Tip-jet helicopters operate by utilizing the reaction force generated by a high-speed tip jet, offering advantages such as a simplified and compact fuselage design and a reduction in empty weight by eliminating anti-torque balancing equipment. In tip-jet helicopter research, the composite power system is regarded as a crucial and bottleneck element. This study employs numerical simulations to comprehensively analyze the internal flow characteristics of the gas generator and tip-jet-driven rotor within the composite power system. Specifically, an in-depth investigation has been conducted on the influence laws of various parameters on the system characteristics. These parameters encompass the tip-jet-driven rotor speed, which takes on values of 50 rad/s, 80 rad/s, 100 rad/s, 120 rad/s, and 150 rad/s, the tip-jet-driven rotor length, measured at 1585 mm, 1785 mm, 1985 mm, 2185 mm, 2385 mm, 2585 mm, and 2785 mm, and the tip-jet-driven rotor nozzle area, which is specified by six values corresponding to multiples of the straight section area of the rotor’s internal channel, namely 0.25 times, 0.5 times, 0.75 times, 1 times, 1.25 times, and 1.5 times. The analysis of the obtained results indicates several significant relationships. Firstly, it is observed that the available moment exhibits a linear decrease as the tip-jet-driven rotor speed increases. Secondly, the maximum available moment is attained when the tip-jet-driven rotor length (L) satisfies the relationship L = Vr/2ω. Additionally, the maximum available power is achieved when the transport velocity of the tip-jet-driven rotor nozzle is precisely half of the relative velocity of the nozzle. Moreover, under the condition that the mass flow rate of the tip-jet-driven rotor nozzle remains constant, a positive correlation between the available moment and the reduction in the tip-jet-driven rotor nozzle area is noted.
- Open Access
- 7 January 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-12
Magnetic circuit design for the performance experiment of shear yield stress enhanced by compression of magnetorheological fluids
The shear yield stress is an important parameter for the industrial application of magnetorheological (MR) fluids. A test equipment was designed and built to perform investigations on the behaviours of compression and shear after squeeze of MR fluids. Mathematical expression of magnetic flux density was further established. Furthermore, the magnetic field distribution of the test device based on two-coil mode and single-coil mode was simulated and compared using finite element analysis(ANSYS/Multiphysics). An experimental test system was fabricated and modified based on the final conditions and simulation results. The compression and shear after squeeze performances of MR fluids were tested. The results showed that a smaller initial gap distance or a larger compressive strain corresponds to a larger compressive stress under the same external magnetic field strength. The shear yield stress after the squeeze of MR fluids increases quickly with the increasing compression stress and the increasing magnetic flux density. This test equipment was thought to be suitable for studying the compression and shear after squeeze performances of MR fluids.
- 7 January 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-12
Open AccessMagnetic circuit design for the performance experiment of shear yield stress enhanced by compression of magnetorheological fluids
The shear yield stress is an important parameter for the industrial application of magnetorheological (MR) fluids. A test equipment was designed and built to perform investigations on the behaviours of compression and shear after squeeze of MR fluids. Mathematical expression of magnetic flux density was further established. Furthermore, the magnetic field distribution of the test device based on two-coil mode and single-coil mode was simulated and compared using finite element analysis(ANSYS/Multiphysics). An experimental test system was fabricated and modified based on the final conditions and simulation results. The compression and shear after squeeze performances of MR fluids were tested. The results showed that a smaller initial gap distance or a larger compressive strain corresponds to a larger compressive stress under the same external magnetic field strength. The shear yield stress after the squeeze of MR fluids increases quickly with the increasing compression stress and the increasing magnetic flux density. This test equipment was thought to be suitable for studying the compression and shear after squeeze performances of MR fluids.
- 18 October 2016
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 139 (4) , 041005
Selective Laser Melting of Graphene-Reinforced Inconel 718 Superalloy: Evaluation of Microstructure and Tensile Performance
Graphene nanoplatelets (GNPs) have many outstanding properties, such as high mechanical strengths, light weight, and high electric conductivity. These unique properties make it an ideal reinforcement used for metal matrix composites (MMCs). In the past few years, many studies have been performed to incorporate GNPs into metal matrix and investigate the properties of obtained metal matrix composites. Meanwhile, fabrication of MMCs through laser-assisted additive manufacturing (LAAM) has attracted much attention in recent years due to the advantages of low waste, high precision, short production lead time, and high workpiece complexity capability. In this study, the two attractive features are combined to produce GNPs reinforced MMC using selective laser melting (SLM) process, one of the LAAM processes. The target metal matrix material is Inconel 718, a nickel-based Ni–Cr–Fe austenitic superalloy that possesses excellent workability and mechanical performance, and has wide applications in industries. In the experiment, pure Inconel 718 and GNPs reinforced Inconel 718 composites with two levels of GNPs content (i.e., 0.25 and 1 wt. %) are obtained by SLM. Note that before the SLM process, a novel powder mixture procedure is employed to ensure the even dispersion of GNPs in the Inconel 718 powders. Room temperature tensile tests are conducted to evaluate the tensile properties. Scanning electron microscopy (SEM) observations are conducted to analyze the fracture surface of materials and to understand the reinforcing mechanism. It is found that fabrication of GNPs reinforced MMC using SLM is a viable approach. The obtained composite possesses dense microstructure and significantly enhanced tensile strength. The ultimate tensile strengths (UTSs) are 997.8, 1296.3, and 1511.6 MPa, and the Young's moduli are 475, 536, and 675 GPa, for 0 wt. % (pure Inconel 718), 0.25 wt. %, and 1 wt. % GNP additions, respectively. The bonding between GNPs and matrix material appears to be strong, and GNPs could be retained during the SLM process. The strengthening effect and mechanisms involved in the composites are discussed. Load transfer, thermal expansion coefficient mismatch, and dislocation hindering are believed to be the three main reinforcing mechanisms involved. It should be noted that more work needs to be conducted in the future to obtain more comprehensive information regarding other static and dynamic properties and the high-temperature performances of the GNP-reinforced MMCs produced by SLM. Process parameter optimization should also be investigated.
- 18 October 2016
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 139 (4) , 041005
Selective Laser Melting of Graphene-Reinforced Inconel 718 Superalloy: Evaluation of Microstructure and Tensile Performance
Graphene nanoplatelets (GNPs) have many outstanding properties, such as high mechanical strengths, light weight, and high electric conductivity. These unique properties make it an ideal reinforcement used for metal matrix composites (MMCs). In the past few years, many studies have been performed to incorporate GNPs into metal matrix and investigate the properties of obtained metal matrix composites. Meanwhile, fabrication of MMCs through laser-assisted additive manufacturing (LAAM) has attracted much attention in recent years due to the advantages of low waste, high precision, short production lead time, and high workpiece complexity capability. In this study, the two attractive features are combined to produce GNPs reinforced MMC using selective laser melting (SLM) process, one of the LAAM processes. The target metal matrix material is Inconel 718, a nickel-based Ni–Cr–Fe austenitic superalloy that possesses excellent workability and mechanical performance, and has wide applications in industries. In the experiment, pure Inconel 718 and GNPs reinforced Inconel 718 composites with two levels of GNPs content (i.e., 0.25 and 1 wt. %) are obtained by SLM. Note that before the SLM process, a novel powder mixture procedure is employed to ensure the even dispersion of GNPs in the Inconel 718 powders. Room temperature tensile tests are conducted to evaluate the tensile properties. Scanning electron microscopy (SEM) observations are conducted to analyze the fracture surface of materials and to understand the reinforcing mechanism. It is found that fabrication of GNPs reinforced MMC using SLM is a viable approach. The obtained composite possesses dense microstructure and significantly enhanced tensile strength. The ultimate tensile strengths (UTSs) are 997.8, 1296.3, and 1511.6 MPa, and the Young's moduli are 475, 536, and 675 GPa, for 0 wt. % (pure Inconel 718), 0.25 wt. %, and 1 wt. % GNP additions, respectively. The bonding between GNPs and matrix material appears to be strong, and GNPs could be retained during the SLM process. The strengthening effect and mechanisms involved in the composites are discussed. Load transfer, thermal expansion coefficient mismatch, and dislocation hindering are believed to be the three main reinforcing mechanisms involved. It should be noted that more work needs to be conducted in the future to obtain more comprehensive information regarding other static and dynamic properties and the high-temperature performances of the GNP-reinforced MMCs produced by SLM. Process parameter optimization should also be investigated.