Waldemar Gądek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Waldemar Gądek has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Sylwester Kalisz
Silesian University of Technology, Institute of Power Engineering and Turbomachinery, Konarskiego 20, 44-100 Gliwice, Poland
2 shared publications- Agata Mlonka-Mędrala
Department of Thermal and Fluid Flow Machines, Faculty of Energy and Fuels, AGH University of Krakow, al. A. Mickiewicza 30, 30-059 Krakow, Poland
1 shared publication Izabella Maj
Silesian University of Technology, Institute of Power Engineering and Turbomachinery, Konarskiego 20, 44-100 Gliwice, Poland
1 shared publication- Joanna Wnorowska
Department of Power Engineering and Turbomachinery, Faculty of Energy and Environmental Engineering, Silesian University of Technology, Konarskiego 18, 44-100 Gliwice, Poland
1 shared publication Jorg Maier
Stuttgart University, Institute of Combustion and Power Plant Technology, Pfaffenwaldring 23, 70569 Stuttgart, Germany
1 shared publication- Mauro Prestipino
Department of Engineering, University of Messina, C. da Di Dio, 98166 Messina, Italy
1 shared publication
Latest Publications
- Open Access
Statistical Model for Prediction of Ash Fusion Temperatures from Additive Doped Biomass
The prediction of phase transformation of biomass ashes is challenging due to the highly variable composition of these fuels as well as the complex processes accompanying phase transformations. The AFT (Ash Fusion Temperature) model was performed in Statistica 13.1 software. This model was divided into three separate submodels, which were designed to predict the characteristic ash melting temperatures for raw and modified biomass. It is based on the chemical composition of fuel and ash as obtained using ash analysis standards. For the discussed models, several coefficients describing multiple regression parameters are presented. The AFT model discussed in this article is suitable for predicting ash fusion temperatures for biomass and allows for the prediction of the temperature with an average error of <±70.05 °C for IDT; <±51.98 °C for HT; <±47.52 °C for FT for raw biomass. For some of the additionally tested biomass, a value higher than the average difference between the measured temperature and the designated model was observed (<90 °C). Moreover, morphological analyses of the structure SEM-EDS for ash samples with and without additive were performed.
Open AccessStatistical Model for Prediction of Ash Fusion Temperatures from Additive Doped Biomass
The prediction of phase transformation of biomass ashes is challenging due to the highly variable composition of these fuels as well as the complex processes accompanying phase transformations. The AFT (Ash Fusion Temperature) model was performed in Statistica 13.1 software. This model was divided into three separate submodels, which were designed to predict the characteristic ash melting temperatures for raw and modified biomass. It is based on the chemical composition of fuel and ash as obtained using ash analysis standards. For the discussed models, several coefficients describing multiple regression parameters are presented. The AFT model discussed in this article is suitable for predicting ash fusion temperatures for biomass and allows for the prediction of the temperature with an average error of <±70.05 °C for IDT; <±51.98 °C for HT; <±47.52 °C for FT for raw biomass. For some of the additionally tested biomass, a value higher than the average difference between the measured temperature and the designated model was observed (<90 °C). Moreover, morphological analyses of the structure SEM-EDS for ash samples with and without additive were performed.
- Open Access
- 1 February 2019
- Published by EDP Sciences
- Vol. 82, 01011
Potassium and chlorine distributions in high temperature halloysite formed deposits
The paper presents results of investigations on KCl interaction with halloysite under high temperature conditions. Halloysite is an aluminosilicate that can be used as a fuel additive to prevent chlorine corrosion and formation of low melting corrosive deposits during combustion of biomass. It is claimed that an increase of the emission of gaseous chlorine as HCl(g) and decrease of chlorine share in the ash as result of KCl and halloysite interaction should be expected. During presented tests the mixtures of KCl and halloysite with different ratios were thermally decomposed in a muffle furnace at high temperatures of 900°C and 1100°C. Then, the analyses of potassium and chlorine contents in the formed solid residues were determined. Besides, it has been proved that halloysite addition changes the ash deposit structure as well as increases the ash fusion temperatures. This was supported by performing phase equilibrium calculations for the investigated different halloysite/KCl mixtures. The positive effects of halloysite on potassium capture while reducing chlorine content in solid residue to prevent formation of corrosive deposits have been confirmed.
- 1 February 2019
- Published by EDP Sciences
- Vol. 82, 01011
Open AccessPotassium and chlorine distributions in high temperature halloysite formed deposits
The paper presents results of investigations on KCl interaction with halloysite under high temperature conditions. Halloysite is an aluminosilicate that can be used as a fuel additive to prevent chlorine corrosion and formation of low melting corrosive deposits during combustion of biomass. It is claimed that an increase of the emission of gaseous chlorine as HCl(g) and decrease of chlorine share in the ash as result of KCl and halloysite interaction should be expected. During presented tests the mixtures of KCl and halloysite with different ratios were thermally decomposed in a muffle furnace at high temperatures of 900°C and 1100°C. Then, the analyses of potassium and chlorine contents in the formed solid residues were determined. Besides, it has been proved that halloysite addition changes the ash deposit structure as well as increases the ash fusion temperatures. This was supported by performing phase equilibrium calculations for the investigated different halloysite/KCl mixtures. The positive effects of halloysite on potassium capture while reducing chlorine content in solid residue to prevent formation of corrosive deposits have been confirmed.
- 10 February 2018
- Published by Springer Nature
- p. 119-126
Review of Ash Deposition Coefficients for Selected Biomasses
- 10 February 2018
- Published by Springer Nature
- p. 119-126
Review of Ash Deposition Coefficients for Selected Biomasses
- Open Access
- 17 October 2016
- Published by EDP Sciences
- Vol. 10, 00024
Gasification and pyrolysis of different biomasses in lab scale system: A comparative study
E3S Web of Conferences, open access proceedings in environment, energy and earth sciences
- 17 October 2016
- Published by EDP Sciences
- Vol. 10, 00024
Open AccessGasification and pyrolysis of different biomasses in lab scale system: A comparative study
E3S Web of Conferences, open access proceedings in environment, energy and earth sciences