Elder Alpes de Vasconcelos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Elder Alpes de Vasconcelos has a total of 139 co-authors. Here are the top co-authors by number of shared publications:
- Walter Mendes de Azevedo
Universidade Federal de Pernambuco
22 shared publications E.F. da Silva
9 shared publicationsTeruaki Katsube
6 shared publications- Eronides Felisberto da Silva
Departamento de Física, Universidade Federal de Pernambuco, Cidade Universitária, 50670-901, Recife, PE, Brazil
5 shared publications Hidekazu Uchida
Department of Information and Computer Sciences, Saitama University, 255 Shimo-Okubo, Saitama 338-8570, Japan
5 shared publicationsE F da Silva
Universidade Federal de Pernambuco
4 shared publications
Latest Publications
- 13 June 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (7) , 075028
Synthesis and characterization of carbon nanotubes/silica composites using gum arabic
Silica-coated carbon nanotube has been synthesized through a variety of experimental techniques. In this work, we present results of a route of synthesis for multiwalled carbon nanotubes (MWCNTs)/Silica composites and Silica. This technique involves a reaction of carbon nanotubes dispersed using Gum Arabic with tetraethylorthosilicate (TEOS), Si (OC2H5)4 in solution of ethanol, with NH4OH as catalyst. Characterization of X-ray diffraction, infrared spectroscopy and scanning/transmission electronic microscopy confirmed the MWCNTs/Silica composite synthesis. In this methodology, acids were not used for functionalizing the surface of the carbon nanotubes. We also studied the composite thermal stability. The results of this paper suggest that our methodology can be used to develop less expensive electronic devices such as sensors, biosensors, capacitors, etc. Additionally, our methodology is easy to operate.
- 13 June 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (7) , 075028
Synthesis and characterization of carbon nanotubes/silica composites using gum arabic
Silica-coated carbon nanotube has been synthesized through a variety of experimental techniques. In this work, we present results of a route of synthesis for multiwalled carbon nanotubes (MWCNTs)/Silica composites and Silica. This technique involves a reaction of carbon nanotubes dispersed using Gum Arabic with tetraethylorthosilicate (TEOS), Si (OC2H5)4 in solution of ethanol, with NH4OH as catalyst. Characterization of X-ray diffraction, infrared spectroscopy and scanning/transmission electronic microscopy confirmed the MWCNTs/Silica composite synthesis. In this methodology, acids were not used for functionalizing the surface of the carbon nanotubes. We also studied the composite thermal stability. The results of this paper suggest that our methodology can be used to develop less expensive electronic devices such as sensors, biosensors, capacitors, etc. Additionally, our methodology is easy to operate.
- 1 September 2016
- Published by IOP Publishing in Translational Materials Research
- Vol. 3 (3) , 035001
A versatile technique to transfer multi-walled carbon nanotubes membranes to surfaces
We present a simple and versatile technique to fabricate and transfer multi-walled carbon nanotube (MWCNT) membranes to virtually any substrate, including devices and a large variety of materials with different shapes. First, a mesoporous silica (Mobil Composite material MCM-41)/MWCNT composite is deposited by spin coating on SiO2. Immersion of the wafer in HF solution, releases a floating MWCNT membrane that strongly adheres to any surface that makes contact with it. The process does not require functionalization or surfactants, thus avoiding contamination and additional cleaning steps, and has potential to be extended to allow the fabrication and transfer of membranes of other carbon materials, including other CNT types, fullerenes and graphene.
- 1 September 2016
- Published by IOP Publishing in Translational Materials Research
- Vol. 3 (3) , 035001
A versatile technique to transfer multi-walled carbon nanotubes membranes to surfaces
We present a simple and versatile technique to fabricate and transfer multi-walled carbon nanotube (MWCNT) membranes to virtually any substrate, including devices and a large variety of materials with different shapes. First, a mesoporous silica (Mobil Composite material MCM-41)/MWCNT composite is deposited by spin coating on SiO2. Immersion of the wafer in HF solution, releases a floating MWCNT membrane that strongly adheres to any surface that makes contact with it. The process does not require functionalization or surfactants, thus avoiding contamination and additional cleaning steps, and has potential to be extended to allow the fabrication and transfer of membranes of other carbon materials, including other CNT types, fullerenes and graphene.
- 19 February 2015
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 30 (4)
Metal-insulator-semiconductor capacitors with water-containing hexagonal mesoporous silica (MCM-41) dielectric and high values of capacitance per unit area
There are many studies on the synthesis and structure of mesoporous silica, but few reports on mesoporous silica-based electronic devices using planar technology. Fabrication of low-k insulator films from mesoporous silica has been investigated for years. Trapped water is a nuisance for those intending to use mesoporous silica films as low-k materials, but may be beneficial for other applications. In this work, we fabricated Si metal-insulator-semiconductor capacitors (MIS) with a hexagonal mesoporous silica (MCM-41) film as the dielectric and studied their electrical characteristics. We show that water confined within the dielectric is associated with high values of capacitance per unit area (approximately 1 μ F cm −2 at 100 Hz) and frequency dispersion of the accumulation capacitance. These devices hold potential for the development of high value MIS capacitors, sensors and biosensors.
- 19 February 2015
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 30 (4)
Metal-insulator-semiconductor capacitors with water-containing hexagonal mesoporous silica (MCM-41) dielectric and high values of capacitance per unit area
There are many studies on the synthesis and structure of mesoporous silica, but few reports on mesoporous silica-based electronic devices using planar technology. Fabrication of low-k insulator films from mesoporous silica has been investigated for years. Trapped water is a nuisance for those intending to use mesoporous silica films as low-k materials, but may be beneficial for other applications. In this work, we fabricated Si metal-insulator-semiconductor capacitors (MIS) with a hexagonal mesoporous silica (MCM-41) film as the dielectric and studied their electrical characteristics. We show that water confined within the dielectric is associated with high values of capacitance per unit area (approximately 1 μ F cm −2 at 100 Hz) and frequency dispersion of the accumulation capacitance. These devices hold potential for the development of high value MIS capacitors, sensors and biosensors.
- 6 June 2011
- Published by Elsevier in Solid State Communications
- Vol. 151 (18) , 1252-1255
Electrical and microscopic characterization of ZnO films on p-SiC substrates
- 6 June 2011
- Published by Elsevier in Solid State Communications
- Vol. 151 (18) , 1252-1255
Electrical and microscopic characterization of ZnO films on p-SiC substrates
- 13 May 2011
- Published by Korean Physical Society in Journal of the Korean Physical Society
- Vol. 58 (5(1)) , 1256-1260
Tailoring the Electrical Properties of ZnO/Polyaniline Heterostructures for Device Applications
- 13 May 2011
- Published by Korean Physical Society in Journal of the Korean Physical Society
- Vol. 58 (5(1)) , 1256-1260
Tailoring the Electrical Properties of ZnO/Polyaniline Heterostructures for Device Applications
- 28 April 2011
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 44 (20)
Fabrication and electrical characterization of polyaniline/silicon carbide heterojunctions
We report on the fabrication of silicon carbide/polyaniline heterojunctions produced by spin coating of polyaniline films onto n-type 6H-SiC and 4H-SiC substrates. Atomic force microscopy was used to estimate the surface roughness, and their electrical characteristics were investigated by means of current, capacitance and conductance measurements as a function of frequency and voltages. Reproducible characteristics and rectification ratios as high as 2 × 106 at ±2 V for the 6H-SiC based heterojunctions were obtained. The devices were modelled as Schottky diodes with series resistance and an oxide interfacial oxide layer to account for interface traps. By analysing the forward bias I–V characteristics, we found that the interface trap density for 4H-SiC/PANI heterojunctions is approximately one order of magnitude higher than for 6H-SiC/PANI heterojunctions, which is consistent with previous studies on SiC/SiO2 interface traps. The average value of interface trap densities for 6H-SiC devices was 8.4 × 1011 eV−1 cm−2 and for 4H-SiC it was 2.7 × 1013 eV−1 cm−2. These values are in the range of previous reports on Schottky diodes with polymer layers.
- 28 April 2011
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 44 (20)
Fabrication and electrical characterization of polyaniline/silicon carbide heterojunctions
We report on the fabrication of silicon carbide/polyaniline heterojunctions produced by spin coating of polyaniline films onto n-type 6H-SiC and 4H-SiC substrates. Atomic force microscopy was used to estimate the surface roughness, and their electrical characteristics were investigated by means of current, capacitance and conductance measurements as a function of frequency and voltages. Reproducible characteristics and rectification ratios as high as 2 × 106 at ±2 V for the 6H-SiC based heterojunctions were obtained. The devices were modelled as Schottky diodes with series resistance and an oxide interfacial oxide layer to account for interface traps. By analysing the forward bias I–V characteristics, we found that the interface trap density for 4H-SiC/PANI heterojunctions is approximately one order of magnitude higher than for 6H-SiC/PANI heterojunctions, which is consistent with previous studies on SiC/SiO2 interface traps. The average value of interface trap densities for 6H-SiC devices was 8.4 × 1011 eV−1 cm−2 and for 4H-SiC it was 2.7 × 1013 eV−1 cm−2. These values are in the range of previous reports on Schottky diodes with polymer layers.
- 1 December 2009
- Published by Elsevier in Biosensors and Bioelectronics
- Vol. 25 (4) , 870-876
Potential of a simplified measurement scheme and device structure for a low cost label-free point-of-care capacitive biosensor
- 1 December 2009
- Published by Elsevier in Biosensors and Bioelectronics
- Vol. 25 (4) , 870-876
Potential of a simplified measurement scheme and device structure for a low cost label-free point-of-care capacitive biosensor
- 1 November 2008
- Published by Elsevier in Applied Surface Science
- Vol. 255 (3) , 688-690
A conducting polymer–silicon heterojunction as a new ultraviolet photodetector
- 1 November 2008
- Published by Elsevier in Applied Surface Science
- Vol. 255 (3) , 688-690
A conducting polymer–silicon heterojunction as a new ultraviolet photodetector
- 1 November 2008
- Published by Elsevier in Applied Surface Science
- Vol. 255 (3) , 755-757
A simplified reactive thermal evaporation method for indium tin oxide electrodes
- 1 November 2008
- Published by Elsevier in Applied Surface Science
- Vol. 255 (3) , 755-757
A simplified reactive thermal evaporation method for indium tin oxide electrodes