Atsushi Matsumoto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Atsushi Matsumoto has a total of 122 co-authors. Here are the top co-authors by number of shared publications:
- Kouichi Akahane
National Institute of Information and Communications Technology, Koganei, Japan
25 shared publications - Naokatsu Yamamoto
National Institute of Information and Communications Technology
19 shared publications - Toshimasa Umezawa
National Institute of Information and Communications Technology (NICT) 4-2-1, Nukui-Kitamachi, Koganei, Tokyo 184-8795, Japan
13 shared publications - Atsushi Kanno
Network Research Institute, National Institute of Information and Communication Technology, Tokyo, Japan
11 shared publications - Gong-Ru Lin
Department of Electrical Engineering, Graduate Institute of Photonics and Optoelectronics, National Taiwan University, Taipei, Taiwan
8 shared publications - Chih-Hsien Cheng
Division of Liver and Transplantation Surgery, Department of General Surgery, Chang-Gung Memorial Hospital, 5, Fu-Hsing Street, Linkou, Taoyuan 333423, Taiwan
7 shared publications
Latest Publications
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (13) , 5570-5578
All-Fiber-Based Interplay of Bunched, Noise-Like and Dissipative Solitons in Nearly Zero-Dispersion EDFL
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (13) , 5570-5578
All-Fiber-Based Interplay of Bunched, Noise-Like and Dissipative Solitons in Nearly Zero-Dispersion EDFL
- 27 April 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (9) , 16723-16737
150-GHz wide-bandwidth balanced photodetector for high-baud-rate PSK signal detection
We present a newly developed integrated high-speed balanced photodetector (BPD) with a 3 dB bandwidth of 150 GHz and a common-mode rejection ratio (CMRR) of -30 dB, along with its demonstration for high-speed DPSK signal detection targeting next-generation high-baud-rate digital coherent receiver applications. The BPD design employs a uni-traveling carrier (UTC) PD with a well-optimized epitaxial layer structure and a narrow-pitch layout for the two PDs. Using high-speed DPSK signals, we successfully demonstrated fundamental push–pull operation up to 100 Gbaud. The device design, fabrication, and measured characteristics of the BPD are discussed in conjunction with the signal detection demonstration.
- 27 April 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (9) , 16723-16737
150-GHz wide-bandwidth balanced photodetector for high-baud-rate PSK signal detection
We present a newly developed integrated high-speed balanced photodetector (BPD) with a 3 dB bandwidth of 150 GHz and a common-mode rejection ratio (CMRR) of -30 dB, along with its demonstration for high-speed DPSK signal detection targeting next-generation high-baud-rate digital coherent receiver applications. The BPD design employs a uni-traveling carrier (UTC) PD with a well-optimized epitaxial layer structure and a narrow-pitch layout for the two PDs. Using high-speed DPSK signals, we successfully demonstrated fundamental push–pull operation up to 100 Gbaud. The device design, fabrication, and measured characteristics of the BPD are discussed in conjunction with the signal detection demonstration.
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Quantum Engineering
- Vol. 7, 4101915
Automated Active-Visibility-Control Loop for Stabilized DPS-QKD Decoding Under Dynamic Wavelength Drift
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Quantum Engineering
- Vol. 7, 4101915
Open AccessAutomated Active-Visibility-Control Loop for Stabilized DPS-QKD Decoding Under Dynamic Wavelength Drift
- 10 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (6) , 2173-2186
Low-DC-Biased 940-nm Square Arrayed VCSELs for Free-Space NRZ-OOK and QAM-DMT Links
High-power 940-nm vertical-cavity surface-emitting laser arrays with different amounts of honeycomb-aligned VCSEL pixels usually serve as the carrier for the time-of-flight (ToF) applications. Under the pulsated ToF application at a relatively low DC bias, the demand of concurrent applications in free-space optical (FSO) transmission can be supported. To demonstrate the multiple functionalities of square-arrayed VCSELs, both non-return-to-zero on-off keying (NRZ-OOK) and quadrature amplitude modulation discrete multitone (QAM-DMT) formats are used to enable directly encoded FSO transmission. The maximum NRZ-OOK encoding data rates for the 1-/2-/2.5-Watt VCSEL arrays are 1.7/1.5/1.3 Gbps and 2.0/1.7/1.6 Gbps, respectively, to meet datacom and telecom standards. By changing the data format to the 4-QAM-DMT stream, the maximum data rates can reach 3.5/3.42/3.32 Gbps, respectively. A VCSEL array with more VCSEL pixels performs worse transmission but provides greater optical power. In addition, the VCSEL arrays operating beyond 1.4Ith exhibit higher transverse modes to degrade the QAM-DMT performance. For the 8-/16-/32-QAM-DMT transmission using the 1-Watt VCSEL array, the maximum data rates are obtained as 5.19/6.56/7.25 Gbps, respectively. These high-level QAM-DMT performances can surpass NRZ-OOK to explore the possibility of an FSO link using a typical high-power VCSEL array for lidar and ToF applications.
- 10 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (6) , 2173-2186
Low-DC-Biased 940-nm Square Arrayed VCSELs for Free-Space NRZ-OOK and QAM-DMT Links
High-power 940-nm vertical-cavity surface-emitting laser arrays with different amounts of honeycomb-aligned VCSEL pixels usually serve as the carrier for the time-of-flight (ToF) applications. Under the pulsated ToF application at a relatively low DC bias, the demand of concurrent applications in free-space optical (FSO) transmission can be supported. To demonstrate the multiple functionalities of square-arrayed VCSELs, both non-return-to-zero on-off keying (NRZ-OOK) and quadrature amplitude modulation discrete multitone (QAM-DMT) formats are used to enable directly encoded FSO transmission. The maximum NRZ-OOK encoding data rates for the 1-/2-/2.5-Watt VCSEL arrays are 1.7/1.5/1.3 Gbps and 2.0/1.7/1.6 Gbps, respectively, to meet datacom and telecom standards. By changing the data format to the 4-QAM-DMT stream, the maximum data rates can reach 3.5/3.42/3.32 Gbps, respectively. A VCSEL array with more VCSEL pixels performs worse transmission but provides greater optical power. In addition, the VCSEL arrays operating beyond 1.4Ith exhibit higher transverse modes to degrade the QAM-DMT performance. For the 8-/16-/32-QAM-DMT transmission using the 1-Watt VCSEL array, the maximum data rates are obtained as 5.19/6.56/7.25 Gbps, respectively. These high-level QAM-DMT performances can surpass NRZ-OOK to explore the possibility of an FSO link using a typical high-power VCSEL array for lidar and ToF applications.
- 6 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (24) , 10871-10881
OFDM Four-Color Micro-LED Point-to-Point Data Link beyond 17 Gbit/s
This study develops high-performance red (R), yellow (Y), green (G), and blue (B) micro light-emitting diodes (μ-LEDs), achieving a total data transmission rate exceeding 17.73 Gbit/s using quadrature-amplitude-modulation (QAM) orthogonal frequency-division multiplexing (OFDM) and bit-loading discrete multitone (BL-DMT) modulation formats. With the greedy bandwidth management program specifically designed for broadband digital encoding of all four-colored μ-LEDs with quite limited bandwidth, the R/Y/G/B μ-LEDs respectively achieve the BL-DMT at their maximal allowable bit-rate of 2.25/3.00/5.36/7.12 Gbit/s, demonstrating their exceptional potential for high-speed digital optical communication with configurable format allocation and optimized spectral usage efficiency. By optimizing semipolar structures, strain-relief designs, and advanced packaging technologies, these μ-LEDs achieve enhanced data efficiency, concurrently paving the way for next-generation smart displays and optical communication applications.
- 6 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (24) , 10871-10881
OFDM Four-Color Micro-LED Point-to-Point Data Link beyond 17 Gbit/s
This study develops high-performance red (R), yellow (Y), green (G), and blue (B) micro light-emitting diodes (μ-LEDs), achieving a total data transmission rate exceeding 17.73 Gbit/s using quadrature-amplitude-modulation (QAM) orthogonal frequency-division multiplexing (OFDM) and bit-loading discrete multitone (BL-DMT) modulation formats. With the greedy bandwidth management program specifically designed for broadband digital encoding of all four-colored μ-LEDs with quite limited bandwidth, the R/Y/G/B μ-LEDs respectively achieve the BL-DMT at their maximal allowable bit-rate of 2.25/3.00/5.36/7.12 Gbit/s, demonstrating their exceptional potential for high-speed digital optical communication with configurable format allocation and optimized spectral usage efficiency. By optimizing semipolar structures, strain-relief designs, and advanced packaging technologies, these μ-LEDs achieve enhanced data efficiency, concurrently paving the way for next-generation smart displays and optical communication applications.
- 25 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (20) , 9612-9627
Enhanced O-Band Si Mach--Zehnder Modulator With Dual/Triple Low-Impedance Termination
By designing the traveling-wave electrode of the O-band Si-waveguide Mach-Zehnder modulator (MZM) with dual-end-port signal-to-ground p-n junction resistors, and encoding the pre-emphasized non-return-to-zero on-off keying (NRZ-OOK) data stream with dual- or triple-port low-impedance (low-Z) termination, the superposition between transmitted and reflected modulations can be fine-tuned to achieve beyond 67-Gbps operation per channel. Such a low-impedance-mismatched termination by using either a dual-port (with 45 Ω or 20 Ω) built-in resistors or a triple-port (with 30 Ω) terminators is compared with each other, indicating that the overly reflected modulation (with 20-Ω impedance) lengthens the rising/falling edges by 3-5 ps and scales down the electrical-to-optical bandwidth to 34.4 GHz. The high voltage standing wave ratio provides a degraded bandwidth of 5.5 GHz and a bit-error ratio of 2 orders of magnitude higher than the other two designs. In contrast, the dual-parallel-resistor-based low-Z (45-Ω) MZM respectively improves the NRZ-OOK to beyond 60-Gbps and nearly 50-Gbps after back-to-back, 2-km, and 10-km SMF transmissions defined by the IEEE 802.3bs standard. By using the tri-port terminated scheme with leveraged impedance of nearly 30 Ω, the managed reflection further enhances the standing-wave effect with periodical carrier depletion to improve the modulation efficiency, hence achieving the highest NRZ-OOK data rate of 67 Gbps and passing the telecom BER criterion after 2-km and 10-km SMF transmissions.
- 25 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (20) , 9612-9627
Enhanced O-Band Si Mach--Zehnder Modulator With Dual/Triple Low-Impedance Termination
By designing the traveling-wave electrode of the O-band Si-waveguide Mach-Zehnder modulator (MZM) with dual-end-port signal-to-ground p-n junction resistors, and encoding the pre-emphasized non-return-to-zero on-off keying (NRZ-OOK) data stream with dual- or triple-port low-impedance (low-Z) termination, the superposition between transmitted and reflected modulations can be fine-tuned to achieve beyond 67-Gbps operation per channel. Such a low-impedance-mismatched termination by using either a dual-port (with 45 Ω or 20 Ω) built-in resistors or a triple-port (with 30 Ω) terminators is compared with each other, indicating that the overly reflected modulation (with 20-Ω impedance) lengthens the rising/falling edges by 3-5 ps and scales down the electrical-to-optical bandwidth to 34.4 GHz. The high voltage standing wave ratio provides a degraded bandwidth of 5.5 GHz and a bit-error ratio of 2 orders of magnitude higher than the other two designs. In contrast, the dual-parallel-resistor-based low-Z (45-Ω) MZM respectively improves the NRZ-OOK to beyond 60-Gbps and nearly 50-Gbps after back-to-back, 2-km, and 10-km SMF transmissions defined by the IEEE 802.3bs standard. By using the tri-port terminated scheme with leveraged impedance of nearly 30 Ω, the managed reflection further enhances the standing-wave effect with periodical carrier depletion to improve the modulation efficiency, hence achieving the highest NRZ-OOK data rate of 67 Gbps and passing the telecom BER criterion after 2-km and 10-km SMF transmissions.
- 2 October 2024
- Published by Springer Nature
- p. 1377-1410
Advanced Monolithic and Heterogeneous Photonic Integration Technology
- 2 October 2024
- Published by Springer Nature
- p. 1377-1410
Advanced Monolithic and Heterogeneous Photonic Integration Technology
- Open Access
- 19 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (21) , 7468-7475
Quantum Well Optical Modulator With Circular Patch Antenna for Millimeter-Wave Radio Over Fiber System
A circular patch antenna-coupled quantum well optical modulator for 1550 nm is proposed for the incident millimeter-wave polarization angle-independent phase modulation. The core layer of the modulator is composed of a multiple five-layer asymmetric coupled quantum well structure. The design and theoretical millimeter wave reception characteristics of circular and rectangular patch antennas with a gap structure are theoretically discussed for comparison. The circular antenna with an outer radius of 330 μm and a gap radius of 310 μm is designed. The optical phase modulators with both types of antennas are fabricated, and their modulation characteristics in the 60 GHz millimeter wave band are demonstrated and compared. The phase modulation independent of the incident millimeter-wave polarization angle is successfully realized. The CSR of 55.0 dB (3.56 mrad of phase shift) is obtained when irradiated with 60 GHz millimeter waves. The phase shift of 3.0 to 3.6 mrad is obtained at any polarization angle of the radio waves at an incident power density of 4.4 W/m2.
- 19 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (21) , 7468-7475
Open AccessQuantum Well Optical Modulator With Circular Patch Antenna for Millimeter-Wave Radio Over Fiber System
A circular patch antenna-coupled quantum well optical modulator for 1550 nm is proposed for the incident millimeter-wave polarization angle-independent phase modulation. The core layer of the modulator is composed of a multiple five-layer asymmetric coupled quantum well structure. The design and theoretical millimeter wave reception characteristics of circular and rectangular patch antennas with a gap structure are theoretically discussed for comparison. The circular antenna with an outer radius of 330 μm and a gap radius of 310 μm is designed. The optical phase modulators with both types of antennas are fabricated, and their modulation characteristics in the 60 GHz millimeter wave band are demonstrated and compared. The phase modulation independent of the incident millimeter-wave polarization angle is successfully realized. The CSR of 55.0 dB (3.56 mrad of phase shift) is obtained when irradiated with 60 GHz millimeter waves. The phase shift of 3.0 to 3.6 mrad is obtained at any polarization angle of the radio waves at an incident power density of 4.4 W/m2.
- 31 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (4) , 1861-1867
AAO Diffused Red-Green-Blue LD White-Light Bulb for 39.6-Gbit/s Data Link
Lighting communication is the ongoing development in human society for fulfilling the practical need of full-space network coverage with heterogeneous wired and wireless communication infrastructures. Light-emitting diodes (LEDs) and laser diodes (LDs) have been successfully introduced as the optical wireless communications data carrier. The latter reveals better data transmission performance owing to its higher modulation bandwidth under the assistance of inherent relaxation oscillation behavior. However, the LD can hardly perform the white-lighting feature due to its beam collimation nature which only provides intense illumination at a point. To concurrently approach the divergent lighting and wireless communication in free space, the white-lighting bulb with a diffuser cap made by co-packing red, green, and blue laser diodes in one copper housing mount is demonstrated with its illuminance lux (ILX) of >300 lx, correlated color temperature (CCT) of 6500K, and color-rendering-index (CRI) of >80. For on-desk light communication, such an RGB-LD white-light bulb enables the on-desk lighting and short-reach data broadcasting with an allowable data rate of up to 39.6 Gbit/s under the 16-QAM DMT format through the tri-color R/G/B channels.
- 31 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (4) , 1861-1867
AAO Diffused Red-Green-Blue LD White-Light Bulb for 39.6-Gbit/s Data Link
Lighting communication is the ongoing development in human society for fulfilling the practical need of full-space network coverage with heterogeneous wired and wireless communication infrastructures. Light-emitting diodes (LEDs) and laser diodes (LDs) have been successfully introduced as the optical wireless communications data carrier. The latter reveals better data transmission performance owing to its higher modulation bandwidth under the assistance of inherent relaxation oscillation behavior. However, the LD can hardly perform the white-lighting feature due to its beam collimation nature which only provides intense illumination at a point. To concurrently approach the divergent lighting and wireless communication in free space, the white-lighting bulb with a diffuser cap made by co-packing red, green, and blue laser diodes in one copper housing mount is demonstrated with its illuminance lux (ILX) of >300 lx, correlated color temperature (CCT) of 6500K, and color-rendering-index (CRI) of >80. For on-desk light communication, such an RGB-LD white-light bulb enables the on-desk lighting and short-reach data broadcasting with an allowable data rate of up to 39.6 Gbit/s under the 16-QAM DMT format through the tri-color R/G/B channels.