Yunsong Gu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yunsong Gu has a total of 77 co-authors. Here are the top co-authors by number of shared publications:
- Linkai Li
College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
6 shared publications Yuhang Zhou
5 shared publicationsLinkai Li
Key Laboratory of Unsteady Aerodynamics and Flow Control, Ministry of Industry and Information Technology, Nanjing University of Aeronautics and Astronautics, Nanjing, China
3 shared publicationsQite Wang
College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing, PR China
3 shared publications- Dachuan Xu
College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
2 shared publications - Jingxiang Chen
Facility Design and Instrumentation Institute, China Aerodynamics Research and Development Center, Mianyang 621000, China
2 shared publications
Latest Publications
- Open Access
Research on Control Laws and Wall Attachment Characteristics of Four-Way Axisymmetric Aerodynamic Vectoring Nozzles Under Low-Speed Jet Conditions
Fluidic thrust vectoring technology has emerged as one of the key research hotspots in next-generation advanced aircraft design, owing to its compact structure, rapid response and low weight penalty. The aerodynamic vectoring nozzle serves as the core component of this technology. Currently, research on four-way axisymmetric fluidic thrust vectoring nozzles remains limited, and corresponding experimental studies suffer from high costs and strict technical requirements. To fill this gap, this paper presents an experimental study on the control laws of an aerodynamic vectoring nozzle prototype under low-speed jet conditions for preliminary design verification. Taking this nozzle type as the research object, the jet deflection characteristics under various wall configurations are investigated at a jet exit velocity of approximately 80 m/s. Among the four evaluated Coanda wall structures, the composite design integrating a smooth curved front section and a beveled rear–middle section is finally determined. Its key performance indicators meet the engineering requirements: a maximum deflection angle of 13.6°, a control linearity of 87.1% for pitch (vertical) control and 89.8% for yaw (lateral) control, a thrust loss of 4%, and a response rate of no less than 200°/s. This work provides a valuable reference for subsequent practical engineering applications.
Open AccessResearch on Control Laws and Wall Attachment Characteristics of Four-Way Axisymmetric Aerodynamic Vectoring Nozzles Under Low-Speed Jet Conditions
Fluidic thrust vectoring technology has emerged as one of the key research hotspots in next-generation advanced aircraft design, owing to its compact structure, rapid response and low weight penalty. The aerodynamic vectoring nozzle serves as the core component of this technology. Currently, research on four-way axisymmetric fluidic thrust vectoring nozzles remains limited, and corresponding experimental studies suffer from high costs and strict technical requirements. To fill this gap, this paper presents an experimental study on the control laws of an aerodynamic vectoring nozzle prototype under low-speed jet conditions for preliminary design verification. Taking this nozzle type as the research object, the jet deflection characteristics under various wall configurations are investigated at a jet exit velocity of approximately 80 m/s. Among the four evaluated Coanda wall structures, the composite design integrating a smooth curved front section and a beveled rear–middle section is finally determined. Its key performance indicators meet the engineering requirements: a maximum deflection angle of 13.6°, a control linearity of 87.1% for pitch (vertical) control and 89.8% for yaw (lateral) control, a thrust loss of 4%, and a response rate of no less than 200°/s. This work provides a valuable reference for subsequent practical engineering applications.
- 4 July 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 178
Experimental investigation of passive fluidic thrust vectoring based on convergent-divergent nozzle
- 4 July 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 178
Experimental investigation of passive fluidic thrust vectoring based on convergent-divergent nozzle
- Open Access
Vectoring Control of Bilateral Parallel Offset Jet: Flow Characteristics and Control Mechanism
We proposed a bilateral parallel offset jet model that enables jet vectoring control without the need for an active high-pressure secondary flow. Flow characteristics, including deflection force, wall pressure distribution, and flow structures, were investigated. The evolutions of key flow structures during jet deflection were investigated, including the passive secondary flow, the shear layer, the boundary layer, and the separation bubble. By analyzing the formation, dissipation, and interactions of the key flow structures, as well as their relationship with pressure characteristics, the mechanism of the jet deflection control was further deduced. The fundamental driving force of the jet deflection stems from the unbalanced pressure difference on either side of the jet, and the valve can control the flow rate of passive secondary flow, thereby altering the near-wall pressure on its side and further generating a pressure that propels the jet to deflect. For walls of different lengths, at a moderate wall length, where L* = 1.5, with the valve controlling the passive secondary flow, a maximum jet vectoring angle of 6.4° can be continuously achieved at a low Reynolds number. Within the range where 20% < δv < 100%, the nonlinear error of jet vectoring control is 5.7%. At a short wall length, where L* = 0.5, the driving force generated by the valve to deflect the jet is insufficient, and the maximum vector angle is 0.3°. For longer walls, the impact of the jet against the trailing edge of the wall obstructs jet deflection; therefore, extending the wall is not conducive to jet vectoring control. Featuring a non-expanding wall structure, the bilateral parallel offset jet model provides a new thrust vectoring control scheme characterized by a compact afterbody, no need for a high-pressure secondary air source, and a simple structure.
Open AccessVectoring Control of Bilateral Parallel Offset Jet: Flow Characteristics and Control Mechanism
We proposed a bilateral parallel offset jet model that enables jet vectoring control without the need for an active high-pressure secondary flow. Flow characteristics, including deflection force, wall pressure distribution, and flow structures, were investigated. The evolutions of key flow structures during jet deflection were investigated, including the passive secondary flow, the shear layer, the boundary layer, and the separation bubble. By analyzing the formation, dissipation, and interactions of the key flow structures, as well as their relationship with pressure characteristics, the mechanism of the jet deflection control was further deduced. The fundamental driving force of the jet deflection stems from the unbalanced pressure difference on either side of the jet, and the valve can control the flow rate of passive secondary flow, thereby altering the near-wall pressure on its side and further generating a pressure that propels the jet to deflect. For walls of different lengths, at a moderate wall length, where L* = 1.5, with the valve controlling the passive secondary flow, a maximum jet vectoring angle of 6.4° can be continuously achieved at a low Reynolds number. Within the range where 20% < δv < 100%, the nonlinear error of jet vectoring control is 5.7%. At a short wall length, where L* = 0.5, the driving force generated by the valve to deflect the jet is insufficient, and the maximum vector angle is 0.3°. For longer walls, the impact of the jet against the trailing edge of the wall obstructs jet deflection; therefore, extending the wall is not conducive to jet vectoring control. Featuring a non-expanding wall structure, the bilateral parallel offset jet model provides a new thrust vectoring control scheme characterized by a compact afterbody, no need for a high-pressure secondary air source, and a simple structure.
- Open Access
Sparse Reconstruction of Pressure Field for Wedge Passive Fluidic Thrust Vectoring Nozzle
Fluidic thrust vectoring control (FTVC) enables highly agile flight without the mechanical complexity of traditional vectoring nozzles. However, a robust onboard identification of the jet deflection state remains challenging when only limited measurements are available. This study proposes a sparse reconstruction of the pressure field method for a wedge passive FTVC nozzle and validates the approach experimentally on a low-speed jet platform. By combining the proper orthogonal decomposition (POD) algorithm with an -regularized compressed sensing method, a full Coanda wall pressure distribution is reconstructed from the sparse measurements. A genetic algorithm is then employed to optimize the wall pressure tap locations, identifying an optimal layout. With only four pressure taps, the local pressure coefficient errors were maintained within < 0.02. In contrast, conventional Kriging interpolation requires increasing the sensor count to 13 to approach the reconstruction level of the proposed POD–compressed sensing method using 4 sensors, yet still exhibits a reduced fidelity in capturing key flow structure characteristics. Overall, the proposed approach provides an efficient and physically interpretable strategy for pressure field estimation, supporting lightweight, low-maintenance, and precise fluidic thrust vectoring control.Open AccessSparse Reconstruction of Pressure Field for Wedge Passive Fluidic Thrust Vectoring Nozzle
Fluidic thrust vectoring control (FTVC) enables highly agile flight without the mechanical complexity of traditional vectoring nozzles. However, a robust onboard identification of the jet deflection state remains challenging when only limited measurements are available. This study proposes a sparse reconstruction of the pressure field method for a wedge passive FTVC nozzle and validates the approach experimentally on a low-speed jet platform. By combining the proper orthogonal decomposition (POD) algorithm with an -regularized compressed sensing method, a full Coanda wall pressure distribution is reconstructed from the sparse measurements. A genetic algorithm is then employed to optimize the wall pressure tap locations, identifying an optimal layout. With only four pressure taps, the local pressure coefficient errors were maintained within < 0.02. In contrast, conventional Kriging interpolation requires increasing the sensor count to 13 to approach the reconstruction level of the proposed POD–compressed sensing method using 4 sensors, yet still exhibits a reduced fidelity in capturing key flow structure characteristics. Overall, the proposed approach provides an efficient and physically interpretable strategy for pressure field estimation, supporting lightweight, low-maintenance, and precise fluidic thrust vectoring control. - 16 December 2025
- Published by Springer Nature in Experiments in Fluids
- Vol. 67  (1) , 6
Pitching moment trend sensing based on vortex identification from surface pressure information on delta wing
- 16 December 2025
- Published by Springer Nature in Experiments in Fluids
- Vol. 67  (1) , 6
Pitching moment trend sensing based on vortex identification from surface pressure information on delta wing
- Open Access
Trailing-Edge Beveling Effect on Passive Fluidic Thrust Vectoring Nozzle Jet Deflection Control
Passive fluidic thrust vectoring nozzles feature a simple structure and low energy consumption. However, traditional 2D passive fluidic thrust vectoring nozzle suffers from jump and control reversal in thrust angle. This study proposes a trailing-edge beveled passive fluidic thrust vectoring nozzle which weakens the jump in thrust vector angle and eliminates control reversal. Experiments were conducted to obtain force angle control characteristics and jet flow structures. Results show that trailing-edge bevel angle significantly affects jet deflection control characteristics: 0° (2D nozzle) and 15° nozzles have obvious thrust vector angle jumps and control reversal, while 30°, 45°, and 60° nozzles eliminate abrupt jumps and no control reversal. However, the maximum thrust vector angle decreases gradually with increasing bevel angle. Then 2D nozzle and typical 45° trailing-edge beveled nozzle were selected for investigation. For 2D nozzle, as secondary flow channel opening difference (δ) increases, all spanwise jets deflect synchronously at δ = 0.58, generating an uncontrolled jump and entering a supercritical state in thrust vector angle. In the range of δ = 0.58~1 the supercritical state diminishes, leading to control reversal. While for 45° beveled nozzle, at δ = 0.35, the jet deflects only at the short side, which weakens thrust vector angle jump. In the range of δ = 0.35~1, jet deflection region expands and produces normal force continuously, which eliminates the thrust vector angle control reversal. The jet deflection region of the beveled nozzle has a smaller spanwise proportion than that of the 2D nozzle, resulting in a reduced maximum vectoring angle. The results show the influence of trailing-edge beveling effect on the flow structure and jet deflection control characteristics under low-speed conditions, yielding valuable insights for the optimization of the design of passive FTVC nozzles.
Open AccessTrailing-Edge Beveling Effect on Passive Fluidic Thrust Vectoring Nozzle Jet Deflection Control
Passive fluidic thrust vectoring nozzles feature a simple structure and low energy consumption. However, traditional 2D passive fluidic thrust vectoring nozzle suffers from jump and control reversal in thrust angle. This study proposes a trailing-edge beveled passive fluidic thrust vectoring nozzle which weakens the jump in thrust vector angle and eliminates control reversal. Experiments were conducted to obtain force angle control characteristics and jet flow structures. Results show that trailing-edge bevel angle significantly affects jet deflection control characteristics: 0° (2D nozzle) and 15° nozzles have obvious thrust vector angle jumps and control reversal, while 30°, 45°, and 60° nozzles eliminate abrupt jumps and no control reversal. However, the maximum thrust vector angle decreases gradually with increasing bevel angle. Then 2D nozzle and typical 45° trailing-edge beveled nozzle were selected for investigation. For 2D nozzle, as secondary flow channel opening difference (δ) increases, all spanwise jets deflect synchronously at δ = 0.58, generating an uncontrolled jump and entering a supercritical state in thrust vector angle. In the range of δ = 0.58~1 the supercritical state diminishes, leading to control reversal. While for 45° beveled nozzle, at δ = 0.35, the jet deflects only at the short side, which weakens thrust vector angle jump. In the range of δ = 0.35~1, jet deflection region expands and produces normal force continuously, which eliminates the thrust vector angle control reversal. The jet deflection region of the beveled nozzle has a smaller spanwise proportion than that of the 2D nozzle, resulting in a reduced maximum vectoring angle. The results show the influence of trailing-edge beveling effect on the flow structure and jet deflection control characteristics under low-speed conditions, yielding valuable insights for the optimization of the design of passive FTVC nozzles.
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37  (9)
Research on the proportional control of rectangular supersonic jet deflection based on passive secondary flow
Supersonic jet deflection control is the core of fluidic thrust vectoring technology. In particular, understanding the evolution law of jet wave structure with nozzle pressure ratio (NPR) can help to clarify the physical mechanism of jet deflection. In this study, a fluidic thrust vectoring nozzle controlled by passive secondary flow is designed. The synchronous schlieren visualization, wall pressure, and force measurement system is developed to investigate the characteristics of the jet under neutral and deflection states. Results show that under different passive secondary flow constraints, the supersonic jet exhibits three wave structure modes. Among them, asymmetric passive secondary flow constraint can cause asymmetric expansion of the jet boundary, thus realizing the deflection control of the supersonic jet. Based on this, the proportional passive secondary flow control method is proposed. When the NPR is 3.0, the maximum passive secondary flow rate is only 1.2% of the primary jet, with a maximum force vectoring angle of 8.8°, and there is no obvious hysteresis phenomenon in the entire vector control process. This control method does not need active secondary flow gas sources and has the significant advantage of simplicity in control. It is expected to play a greater role in the next generation of fluidic thrust vectoring control.
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37  (9)
Research on the proportional control of rectangular supersonic jet deflection based on passive secondary flow
Supersonic jet deflection control is the core of fluidic thrust vectoring technology. In particular, understanding the evolution law of jet wave structure with nozzle pressure ratio (NPR) can help to clarify the physical mechanism of jet deflection. In this study, a fluidic thrust vectoring nozzle controlled by passive secondary flow is designed. The synchronous schlieren visualization, wall pressure, and force measurement system is developed to investigate the characteristics of the jet under neutral and deflection states. Results show that under different passive secondary flow constraints, the supersonic jet exhibits three wave structure modes. Among them, asymmetric passive secondary flow constraint can cause asymmetric expansion of the jet boundary, thus realizing the deflection control of the supersonic jet. Based on this, the proportional passive secondary flow control method is proposed. When the NPR is 3.0, the maximum passive secondary flow rate is only 1.2% of the primary jet, with a maximum force vectoring angle of 8.8°, and there is no obvious hysteresis phenomenon in the entire vector control process. This control method does not need active secondary flow gas sources and has the significant advantage of simplicity in control. It is expected to play a greater role in the next generation of fluidic thrust vectoring control.
- 1 September 2025
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 38  (5)
Normal Force and Pitching Moment Trend Sensing of Delta Wing Based on Flow Physical Topology with Sparse Pressure Measurements
- 1 September 2025
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 38  (5)
Normal Force and Pitching Moment Trend Sensing of Delta Wing Based on Flow Physical Topology with Sparse Pressure Measurements
- Open Access
Experimental Investigation of the Performance of a Novel Ejector–Diffuser System with Different Supersonic Nozzle Arrays
The supersonic–supersonic ejector–diffuser system is employed to suck supersonic low-pressure and low-temperature flow into a high-pressure environment. A new design of a supersonic–supersonic ejector–diffuser was introduced to verify pressure control performance under different operating conditions and vacuum background pressure. A 1D analysis was used to predict the geometrical structure of an ejector–diffuser with a rectangular section based on the given operating conditions. Different numbers and types of nozzle plates were designed and installed on the ejector to study the realizability of avoiding or postponing the aerodynamic choking phenomenon in the mixing section. The effects of different geometrical parameters on the operating performance of the ejector–diffuser system were discussed in detail. Experimental investigation of the effects of different types of nozzle plates and the back pressures on the pressure control performance of the designed ejector–diffuser system were performed in a straight-flow wind tunnel. The results showed that the position, type and number of the nozzle plates have a significant impact on the beginning of the formation of aerodynamic choking. The geometry of the ejector and the operating conditions, especially the backpressure and inlet pressure of the ejecting stream, determined the entrainment ratio of the two supersonic streams. The experimental results showed that long nozzle-plate had a better performance in terms of maintaining pressure stability in the test section, while short a nozzle-plate had a better pressure matching performance and could maintain a higher entrainment ratio under high backpressure conditions.
Open AccessExperimental Investigation of the Performance of a Novel Ejector–Diffuser System with Different Supersonic Nozzle Arrays
The supersonic–supersonic ejector–diffuser system is employed to suck supersonic low-pressure and low-temperature flow into a high-pressure environment. A new design of a supersonic–supersonic ejector–diffuser was introduced to verify pressure control performance under different operating conditions and vacuum background pressure. A 1D analysis was used to predict the geometrical structure of an ejector–diffuser with a rectangular section based on the given operating conditions. Different numbers and types of nozzle plates were designed and installed on the ejector to study the realizability of avoiding or postponing the aerodynamic choking phenomenon in the mixing section. The effects of different geometrical parameters on the operating performance of the ejector–diffuser system were discussed in detail. Experimental investigation of the effects of different types of nozzle plates and the back pressures on the pressure control performance of the designed ejector–diffuser system were performed in a straight-flow wind tunnel. The results showed that the position, type and number of the nozzle plates have a significant impact on the beginning of the formation of aerodynamic choking. The geometry of the ejector and the operating conditions, especially the backpressure and inlet pressure of the ejecting stream, determined the entrainment ratio of the two supersonic streams. The experimental results showed that long nozzle-plate had a better performance in terms of maintaining pressure stability in the test section, while short a nozzle-plate had a better pressure matching performance and could maintain a higher entrainment ratio under high backpressure conditions.
- Open Access
An Optimized Pressure-Based Method for Thrust Vectoring Angle Estimation
This research developed a pressure-based thrust vectoring angle estimation method for fluidic thrust vectoring nozzles. This method can accurately estimate the real-time in-flight thrust vectoring angle using only wall pressure information on the inner surface of the nozzle. We proposed an algorithm to calculate the thrust vectoring angle from the wall pressure inside the nozzle. Non-dominated sorting genetic algorithm II was applied to find the optimal sensor arrays and reduce the wall pressure sensor quantity. Synchronous force and wall pressure measurement experiments were carried out to verify the accuracy and real-time response of the pressure-based thrust vectoring angle estimation method. The results showed that accurate estimation of the thrust vectoring angle can be achieved with a minimum of three pressure sensors. The pressure-based thrust vectoring angle estimation method proposed in this study has a good prospect for engineering applications; it is capable of accurate real-time in-flight monitoring of the thrust vectoring angle. This method is important and indispensable for the closed-loop feedback control and aircraft attitude control of fluidic thrust vectoring control technology.
Open AccessAn Optimized Pressure-Based Method for Thrust Vectoring Angle Estimation
This research developed a pressure-based thrust vectoring angle estimation method for fluidic thrust vectoring nozzles. This method can accurately estimate the real-time in-flight thrust vectoring angle using only wall pressure information on the inner surface of the nozzle. We proposed an algorithm to calculate the thrust vectoring angle from the wall pressure inside the nozzle. Non-dominated sorting genetic algorithm II was applied to find the optimal sensor arrays and reduce the wall pressure sensor quantity. Synchronous force and wall pressure measurement experiments were carried out to verify the accuracy and real-time response of the pressure-based thrust vectoring angle estimation method. The results showed that accurate estimation of the thrust vectoring angle can be achieved with a minimum of three pressure sensors. The pressure-based thrust vectoring angle estimation method proposed in this study has a good prospect for engineering applications; it is capable of accurate real-time in-flight monitoring of the thrust vectoring angle. This method is important and indispensable for the closed-loop feedback control and aircraft attitude control of fluidic thrust vectoring control technology.