Rabi Sankar Panda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Rabi Sankar Panda has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Krishnan Balasubramaniam
Centre for Non-Destructive Evaluation, Indian Institute of Technology Madras, Chennai 600036, India
5 shared publications - Bikash Ghose
Imaging, Detection, Evaluation & Analysis Group (IDEA Group), High Energy Materials Research Laboratory (HEMRL), Sutarwadi, Pune 411021, India
2 shared publications Krishnan Balasubramaniam
Department of Mechanical Engineering, Indian Institute of Technology Madras, Chennai, India
2 shared publicationsPrabhu Rajagopal
Centre for Nondestructive Evaluation (CNDE), Department of Mechanical Engineering, Indian Institute of Technology Madras, Chennai, India
2 shared publications- Prabhu Rajagopal
Department of Mechanical Engineering, Indian Institute of Technology Madras, Chennai, India
2 shared publications Bikash Ghose
DRDO High Energy Materials Research Laboratory, Pune, India
1 shared publication
Latest Publications
- 5 June 2022
- Published by SAGE Publications in Structural Health Monitoring
- Vol. 22 (2) , 1193-1210
A study on the use of fundamental antisymmetric-like guided wave for health monitoring of elastic–viscoelastic bilayer structures
This study investigates the ultrasonic guided wave propagation in an elastic–viscoelastic (steel–rubber) bilayer structure. 2D finite element models are developed in the frequency domain to simulate the wave propagation in the steel–rubber bilayer structure. The guided wave A0 mode is generated in the bilayer with a contact L-wave probe and detected with an out-of-plane laser vibrometer. Several wave features, such as amplitude, phase velocity and phase delay, are measured and compared to determine the characteristic changes of the A0 wave mode in the steel layer alone as well as in the bilayer structure. Studies are also performed for the bilayer structure when excited from the steel and rubber surfaces. The amplitude and phase velocity of the A0 mode are reduced in the bilayer compared to the steel layer alone. The phase velocity of the A0 wave mode in the bilayer does not depend on the viscoelastic properties of the rubber layer, rather depends only on the elastic properties of the rubber layer. The viscoelastic rubber layer in the bilayer structure does not sustain any independent wave mode; instead, it carries the A0 mode of the steel layer alone as a modified A0 wave mode in the bilayer structure. A parametric numerical study of the viscoelasticity of the rubber layer in the bilayer structure shows that the attenuation of the modified A0 mode in the bilayer is more affected by the bulk S-wave attenuation than the bulk L-wave attenuation. The rate of attenuation of the modified A0 mode in the bilayer is faster on the rubber surface than on the steel surface. A study on the A0 wave mode interaction with the interfacial disbond between steel and rubber layers is also carried out.
- 5 June 2022
- Published by SAGE Publications in Structural Health Monitoring
- Vol. 22 (2) , 1193-1210
A study on the use of fundamental antisymmetric-like guided wave for health monitoring of elastic–viscoelastic bilayer structures
This study investigates the ultrasonic guided wave propagation in an elastic–viscoelastic (steel–rubber) bilayer structure. 2D finite element models are developed in the frequency domain to simulate the wave propagation in the steel–rubber bilayer structure. The guided wave A0 mode is generated in the bilayer with a contact L-wave probe and detected with an out-of-plane laser vibrometer. Several wave features, such as amplitude, phase velocity and phase delay, are measured and compared to determine the characteristic changes of the A0 wave mode in the steel layer alone as well as in the bilayer structure. Studies are also performed for the bilayer structure when excited from the steel and rubber surfaces. The amplitude and phase velocity of the A0 mode are reduced in the bilayer compared to the steel layer alone. The phase velocity of the A0 wave mode in the bilayer does not depend on the viscoelastic properties of the rubber layer, rather depends only on the elastic properties of the rubber layer. The viscoelastic rubber layer in the bilayer structure does not sustain any independent wave mode; instead, it carries the A0 mode of the steel layer alone as a modified A0 wave mode in the bilayer structure. A parametric numerical study of the viscoelasticity of the rubber layer in the bilayer structure shows that the attenuation of the modified A0 mode in the bilayer is more affected by the bulk S-wave attenuation than the bulk L-wave attenuation. The rate of attenuation of the modified A0 mode in the bilayer is faster on the rubber surface than on the steel surface. A study on the A0 wave mode interaction with the interfacial disbond between steel and rubber layers is also carried out.
- 1 December 2021
- Published by Elsevier in NDT & E International
- Vol. 124, 102543
Guided A0 wave mode interaction with interfacial disbonds in an elastic-viscoelastic bilayer structure
- 1 December 2021
- Published by Elsevier in NDT & E International
- Vol. 124, 102543
Guided A0 wave mode interaction with interfacial disbonds in an elastic-viscoelastic bilayer structure
- 29 September 2021
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 32 (12) , 124006
Phase velocity measurement of dispersive wave modes by Gaussian peak-tracing in the f-k transform domain
The measurement of guided wave phase velocity is vital for the successful implementation of the guided wave technique for defect detection and material characterization. In this paper, an algorithm for quantitative phase velocity measurement based on f-k (frequency-wavenumber) transformation with a Gaussian fit peak-tracing is proposed. The versatility of the algorithm is demonstrated using numerically simulated data for a wide range of case studies, including non-dispersive, dispersive, dispersive with viscoelasticity, overlapping modes, and highly attenuative materials. It is further validated utilizing two experimental datasets. The maximum error in measuring phase velocity using experimental and numerical data is less than 0.8% when compared to the analytical value obtained using DISPERSE. The phase velocity values obtained with the proposed f-k transformation with a Gaussian fit peak-tracing algorithm are also compared with the conventional methods and found to be superior. Further, the proposed algorithm is suitable for evaluating the phase velocity of the coexistence of forward and reflected wave modes. Hence, the proposed algorithm is appropriate for measuring phase velocity where separation of modes or reflected signal is difficult to achieve, such as for a smaller specimen or even longer specimens with higher-order faster mode.
- 29 September 2021
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 32 (12) , 124006
Phase velocity measurement of dispersive wave modes by Gaussian peak-tracing in the f-k transform domain
The measurement of guided wave phase velocity is vital for the successful implementation of the guided wave technique for defect detection and material characterization. In this paper, an algorithm for quantitative phase velocity measurement based on f-k (frequency-wavenumber) transformation with a Gaussian fit peak-tracing is proposed. The versatility of the algorithm is demonstrated using numerically simulated data for a wide range of case studies, including non-dispersive, dispersive, dispersive with viscoelasticity, overlapping modes, and highly attenuative materials. It is further validated utilizing two experimental datasets. The maximum error in measuring phase velocity using experimental and numerical data is less than 0.8% when compared to the analytical value obtained using DISPERSE. The phase velocity values obtained with the proposed f-k transformation with a Gaussian fit peak-tracing algorithm are also compared with the conventional methods and found to be superior. Further, the proposed algorithm is suitable for evaluating the phase velocity of the coexistence of forward and reflected wave modes. Hence, the proposed algorithm is appropriate for measuring phase velocity where separation of modes or reflected signal is difficult to achieve, such as for a smaller specimen or even longer specimens with higher-order faster mode.
- 1 December 2018
- Published by Elsevier in Composite Structures
- Vol. 206, 247-260
Rapid guided wave inspection of complex stiffened composite structural components using non-contact air-coupled ultrasound
- 1 December 2018
- Published by Elsevier in Composite Structures
- Vol. 206, 247-260
Rapid guided wave inspection of complex stiffened composite structural components using non-contact air-coupled ultrasound
- 24 September 2016
- Published by SAGE Publications in Structural Health Monitoring
- Vol. 16 (2) , 142-152
Characterization of delamination-type damages in composite laminates using guided wave visualization and air-coupled ultrasound
This article reports on the characterization of delamination damages in composite laminates using wave visualization method. A combination of plate-guided ultrasound and air-coupled ultrasonics is used to locate and visualize delaminations. The study focuses on the physics of Lamb wave propagation and interaction with delaminations at various through-thickness locations and positions. Three-dimensional finite element simulations are used to study, in detail, the changes in wave features such as mode velocity, wavelength and wave refraction in the delamination region. These wave features provide information on the location, position and orientation of the delamination. These studies are validated by experimental measurements. The influence of position of source and delamination on wave refraction in the delamination region is examined. This method also correlates the results obtained from experiments and finite element simulations to theoretical dispersion curves in order to distinctly determine the delamination location.
- 24 September 2016
- Published by SAGE Publications in Structural Health Monitoring
- Vol. 16 (2) , 142-152
Characterization of delamination-type damages in composite laminates using guided wave visualization and air-coupled ultrasound
This article reports on the characterization of delamination damages in composite laminates using wave visualization method. A combination of plate-guided ultrasound and air-coupled ultrasonics is used to locate and visualize delaminations. The study focuses on the physics of Lamb wave propagation and interaction with delaminations at various through-thickness locations and positions. Three-dimensional finite element simulations are used to study, in detail, the changes in wave features such as mode velocity, wavelength and wave refraction in the delamination region. These wave features provide information on the location, position and orientation of the delamination. These studies are validated by experimental measurements. The influence of position of source and delamination on wave refraction in the delamination region is examined. This method also correlates the results obtained from experiments and finite element simulations to theoretical dispersion curves in order to distinctly determine the delamination location.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1706, 080002
Rapid non-contact inspection of composite ailerons using air-coupled ultrasound
This paper demonstrates an approach for rapid non-contact air-coupled ultrasonic inspection of composite ailerons with complex cross-sectional profile including thickness changes, curvature and the presence of a number of stiffeners. Low-frequency plate guided ultrasonic modes are used in B-scan mode for the measurements in pitch-catch mode. Appropriate probe holder angles suitable for generating and receiving lower order guided wave modes are discussed. Different embodiments of the pitch-catch tandem positions along and across stiffener and curved regions of the test sample enable a rapid test campaign capturing the feature-rich sample profile. Techniques to distinguish special features in the stiffener are presented.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1706, 080002
Rapid non-contact inspection of composite ailerons using air-coupled ultrasound
This paper demonstrates an approach for rapid non-contact air-coupled ultrasonic inspection of composite ailerons with complex cross-sectional profile including thickness changes, curvature and the presence of a number of stiffeners. Low-frequency plate guided ultrasonic modes are used in B-scan mode for the measurements in pitch-catch mode. Appropriate probe holder angles suitable for generating and receiving lower order guided wave modes are discussed. Different embodiments of the pitch-catch tandem positions along and across stiffener and curved regions of the test sample enable a rapid test campaign capturing the feature-rich sample profile. Techniques to distinguish special features in the stiffener are presented.
- 1 January 2015
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1650 (1) , 1299-1306
An approach for defect visualization and identification in composite plate structures using air-coupled guided ultrasound
Composite materials are today widely used in engineering applications because of superior strength-weight ratios offered by them as well as high structural performance and corrosion resistance. However defects such as fibre breakage, matrix cracking, de-bonding and delaminations in composites impact their structural integrity and reliability negatively and NDE techniques to rapidly identify such defects are valuable. Ultrasonic guided waves have over the years emerged as attractive tools for scanning of large structures and recently they have been considered for rapid inspection of plate and pipe installations. Air-coupled ultrasound for generation of Lamb waves is particularly attractive for composite applications in view of the non-contact inspection offered, as well as the possibilities for rapid mechanized scanning. In this paper we present damage identification and visualisation approaches for quasi-isotropic composite plate structures, based on air-coupled plate guided ultrasonic (Lamb) waves. In the implementation demonstrated, an 8-layered quasi-isotropic [0/+45/−45/90]s glass fibre reinforced plastics (GFRP) composite plate is interrogated using air-coupled pitch-catch guided ultrasound. Propagation of Lamb waves in the laminates and their interaction with delaminations of different sizes at various locations along the structure are studied using 3D finite element (FE) analysis. The visualization approach is validated using experiments, leading to quantitative predictions of defect parameters such as sizing, location and depth. The approach is also extended for the inspection of complex composite structural features such as I- and T-sections.
- 1 January 2015
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1650 (1) , 1299-1306
An approach for defect visualization and identification in composite plate structures using air-coupled guided ultrasound
Composite materials are today widely used in engineering applications because of superior strength-weight ratios offered by them as well as high structural performance and corrosion resistance. However defects such as fibre breakage, matrix cracking, de-bonding and delaminations in composites impact their structural integrity and reliability negatively and NDE techniques to rapidly identify such defects are valuable. Ultrasonic guided waves have over the years emerged as attractive tools for scanning of large structures and recently they have been considered for rapid inspection of plate and pipe installations. Air-coupled ultrasound for generation of Lamb waves is particularly attractive for composite applications in view of the non-contact inspection offered, as well as the possibilities for rapid mechanized scanning. In this paper we present damage identification and visualisation approaches for quasi-isotropic composite plate structures, based on air-coupled plate guided ultrasonic (Lamb) waves. In the implementation demonstrated, an 8-layered quasi-isotropic [0/+45/−45/90]s glass fibre reinforced plastics (GFRP) composite plate is interrogated using air-coupled pitch-catch guided ultrasound. Propagation of Lamb waves in the laminates and their interaction with delaminations of different sizes at various locations along the structure are studied using 3D finite element (FE) analysis. The visualization approach is validated using experiments, leading to quantitative predictions of defect parameters such as sizing, location and depth. The approach is also extended for the inspection of complex composite structural features such as I- and T-sections.