Hyunok Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hyunok Kim has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Alexander L. Kitt
EWI, Columbus, USA
1 shared publication Anoop Samant
KTH Parts Industries Inc.; K-Group Technical R&D Center, 8205 Business Way, Plain City, OH 43064
1 shared publicationCliff Hoschouer
SHILOH, 5580 Wegman Drive, Valley City, Ohio 44280, USA
1 shared publicationJ. Gu
EWI—Forming Center (EWI-FC)
1 shared publicationJiahui Gu
1 shared publicationJianhui Shang
EWI Forming Center, 1250 Arthur E. Adams Drive, Columbus, Ohio 43221, USA
1 shared publication
Latest Publications
- 1 July 2022
- Published by Springer Nature
- p. 627-634
Strain Rate-Dependent Hardening Behavior of Weld Metal in Laser Welded Blanks with GEN3 AHSS
- 1 July 2022
- Published by Springer Nature
- p. 627-634
Strain Rate-Dependent Hardening Behavior of Weld Metal in Laser Welded Blanks with GEN3 AHSS
- Open Access
- 14 October 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (20) , 9530
Profit-Driven Methodology for Servo Press Motion Selection under Material Variability
Servo presses enable new types of forming motion profiles that can be used to stamp difficult materials, such as high strength steels. This paper presents an application of Bayesian statistics to intelligently select which motion profile maximizes the expected utility given the properties of the incoming material. Bayesian logistic regression was used in conjunction with expected utility to estimate manufacturing returns, which can be used to make informed process decisions. A use case is presented, which demonstrates that the Smart Forming Algorithm can increase expected returns by more than 20%.
- 14 October 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (20) , 9530
Open AccessProfit-Driven Methodology for Servo Press Motion Selection under Material Variability
Servo presses enable new types of forming motion profiles that can be used to stamp difficult materials, such as high strength steels. This paper presents an application of Bayesian statistics to intelligently select which motion profile maximizes the expected utility given the properties of the incoming material. Bayesian logistic regression was used in conjunction with expected utility to estimate manufacturing returns, which can be used to make informed process decisions. A use case is presented, which demonstrates that the Smart Forming Algorithm can increase expected returns by more than 20%.
- 11 July 2021
- Published by Springer Nature
- p. 2631-2638
Evaluating 980GEN-3 Steel with Tested and Numerical Forming Limit Curves
- 11 July 2021
- Published by Springer Nature
- p. 2631-2638
Evaluating 980GEN-3 Steel with Tested and Numerical Forming Limit Curves
- Open Access
- 21 September 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 418 (1) , 012029
Comparison of Drawability between Warm Forming and Cold Forming of Aluminum 6xxx Alloys
- 21 September 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 418 (1) , 012029
Open AccessComparison of Drawability between Warm Forming and Cold Forming of Aluminum 6xxx Alloys
- Open Access
- 31 August 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 734 (3) , 032025
Development of new hole expansion testing method
This paper introduces a new hole expansion (HE) testing method that could be more relevant to the edge cracking problem observed in stamping advanced high strength steel (AHSS). The new testing method adopted a large hole diameter of 75 mm compared to the standard hole diameter of 10 mm. An inline monitoring system was developed to visually monitor the hole edge cracking during the test and synchronize the load-displacement data with the recorded video for capturing the initial crack. A new hole expansion testing method was found to be effective in evaluating the edge cracking by considering the effects of material properties and trimming methods. It showed a much larger difference, up to 11%, of the HE ratio between DP980 and TRIP780 compared to the standard HE testing method giving less than a 2% difference.
- 31 August 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 734 (3) , 032025
Open AccessDevelopment of new hole expansion testing method
This paper introduces a new hole expansion (HE) testing method that could be more relevant to the edge cracking problem observed in stamping advanced high strength steel (AHSS). The new testing method adopted a large hole diameter of 75 mm compared to the standard hole diameter of 10 mm. An inline monitoring system was developed to visually monitor the hole edge cracking during the test and synchronize the load-displacement data with the recorded video for capturing the initial crack. A new hole expansion testing method was found to be effective in evaluating the edge cracking by considering the effects of material properties and trimming methods. It showed a much larger difference, up to 11%, of the HE ratio between DP980 and TRIP780 compared to the standard HE testing method giving less than a 2% difference.