Wanlop Kitisatorn
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Wanlop Kitisatorn has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Pornlada Pongmuksuwan
3 shared publications- Pornlada Pongmuksuwan
King Mongkut’s University of Technology North Bangkok
2 shared publications Kantima Chaochanchaikul
Division of Industrial Materials Science, Faculty of Science and Technology, Rajamangala University of Technology Phra Nakhon, Bangkok, Thailand
1 shared publication- Kiadtisak Salayong
Research Center of Innovation Digital and Electromagnetic Technology (iDEMT), Department of Teacher Training in Electrical Engineering, Faculty of Technical Education, King Mongkut’s University of Technology North Bangkok, 1518, Pracharat 1 Road, Wongsawang, Bangsue, Bangkok 10800, Thailand
1 shared publication - Kiattisak Noknoi
Kasetsart University
1 shared publication - Narit Intawong
Rajamangala University of Technology Lanna
1 shared publication
Latest Publications
- 9 February 2026
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 385, 85-92
Development of a Self-Healing Coating by Microencapsulation Technique
This research aims to develop self-healing coatings using a microencapsulation technique. Microcapsules were synthesized by polymerizing isocyanate-based shell materials (pTDI, pMDI, and TDI) with HDI derivatives as the core substances. The study focused on evaluating the effect of precursor types and stirring speeds on the morphology and particle size of the microcapsules. Among the tested materials, microcapsules with TDI shells and HDI biuret cores exhibited optimal structural characteristics, including clear core encapsulation and spherical shape. FTIR analysis confirmed the successful formation of polyurethane shells. Stirring speed was found to significantly influence particle size: increasing speed reduced microcapsule size up to a point, but excessive speed (800 rpm) led to aggregation and size increase due to turbulence. The synthesized microcapsules show potential for improving the corrosion resistance and durability of coatings through autonomous repair, contributing to longer service life and reduced maintenance costs in industrial applications.
- 9 February 2026
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 385, 85-92
Development of a Self-Healing Coating by Microencapsulation Technique
This research aims to develop self-healing coatings using a microencapsulation technique. Microcapsules were synthesized by polymerizing isocyanate-based shell materials (pTDI, pMDI, and TDI) with HDI derivatives as the core substances. The study focused on evaluating the effect of precursor types and stirring speeds on the morphology and particle size of the microcapsules. Among the tested materials, microcapsules with TDI shells and HDI biuret cores exhibited optimal structural characteristics, including clear core encapsulation and spherical shape. FTIR analysis confirmed the successful formation of polyurethane shells. Stirring speed was found to significantly influence particle size: increasing speed reduced microcapsule size up to a point, but excessive speed (800 rpm) led to aggregation and size increase due to turbulence. The synthesized microcapsules show potential for improving the corrosion resistance and durability of coatings through autonomous repair, contributing to longer service life and reduced maintenance costs in industrial applications.
- 2 February 2026
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 447, 23-31
Influence of Filler on the Interfacial Strength between TPE and PP Composites
The influence of filler type and content on the wettability and interfacial bonding between thermoplastic elastomer (TPE) and polypropylene (PP) by using the injection overmolding process was investigated in this study. Calcium carbonate (CaCO 3 ) and talcum (Talc) masterbatchs, ranging from 0 to 40 percent by weight (wt%), were mixed into the PP matrix as fillers. The bond strength of TPE overmolded onto PP composites was characterized by the tensile and tear tests. Good compatibility was observed between TPE and PP filled with various amounts of CaCO 3 and Talc. In the case of the tensile test, the crack initiation stress, ultimate tensile strength, strain at break, and bond energy were found to decrease with increasing filler content. The results obtained from the tear test indicated that the propagation strength, ultimate tear strength, strain at break, and bond energy of injection overmolded TPE-PP filled with various CaCO 3 contents did not significantly change compared to those obtained from Talc. This can be attributed to the high reinforcing efficiency of Talc in comparison with CaCO 3 , which can enhance the stiffness and thermal resistance of the PP matrix. As a result, the contact area becomes more resistant to molecular diffusion of TPE chains, particularly at high Talc loadings (30 and 40 wt%), leading to the reduction of interfacial bonding.
- 2 February 2026
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 447, 23-31
Influence of Filler on the Interfacial Strength between TPE and PP Composites
The influence of filler type and content on the wettability and interfacial bonding between thermoplastic elastomer (TPE) and polypropylene (PP) by using the injection overmolding process was investigated in this study. Calcium carbonate (CaCO 3 ) and talcum (Talc) masterbatchs, ranging from 0 to 40 percent by weight (wt%), were mixed into the PP matrix as fillers. The bond strength of TPE overmolded onto PP composites was characterized by the tensile and tear tests. Good compatibility was observed between TPE and PP filled with various amounts of CaCO 3 and Talc. In the case of the tensile test, the crack initiation stress, ultimate tensile strength, strain at break, and bond energy were found to decrease with increasing filler content. The results obtained from the tear test indicated that the propagation strength, ultimate tear strength, strain at break, and bond energy of injection overmolded TPE-PP filled with various CaCO 3 contents did not significantly change compared to those obtained from Talc. This can be attributed to the high reinforcing efficiency of Talc in comparison with CaCO 3 , which can enhance the stiffness and thermal resistance of the PP matrix. As a result, the contact area becomes more resistant to molecular diffusion of TPE chains, particularly at high Talc loadings (30 and 40 wt%), leading to the reduction of interfacial bonding.
- Open Access
- 22 January 2026
- Published by Elsevier in Industrial Crops and Products
- Vol. 240
Preparation and characterization of palm oil-based polyurethane foam using polysorbate as a green ring-opening agent
- 22 January 2026
- Published by Elsevier in Industrial Crops and Products
- Vol. 240
Open AccessPreparation and characterization of palm oil-based polyurethane foam using polysorbate as a green ring-opening agent
- Open Access
- 27 September 2023
- Published by Elsevier in Applied Surface Science Advances
- Vol. 18, 100458
Microencapsulated epoxidized palm oil: A self-healing coating solution
- 27 September 2023
- Published by Elsevier in Applied Surface Science Advances
- Vol. 18, 100458
Open AccessMicroencapsulated epoxidized palm oil: A self-healing coating solution
- Open Access
Electromagnetic Absorption and Mechanical Properties of Natural Rubber Composites Based on Conductive Carbon Black and Fe3O4
In contemporary civilization, the electromagnetic radiation from electronic devices and communication systems has become a substantial pollutant. High-performance electromagnetic absorbers have become a solution for absorbing unwanted electromagnetic waves. This research proposed a lightweight and flexible electromagnetic absorber produced from natural rubber filled with conductive carbon black (CCB) and Fe3O4. The effect of CCB, Fe3O4, and a combination of CCB and Fe3O4 as a hybrid filler on foam morpholog, electromagnetic reflectivity, tensile strength, and compression set properties were investigated. In addition, the effect of the alternating layered structure of CCB and Fe3O4 on electromagnetic absorption was investigated. The results indicated that the composite foam exhibited an interconnected network structure that enhanced the electromagnetic attenuation in the absorber. CCB increased the electromagnetic absorption of the foam, whereas Fe3O4 had less of an effect. The foam filled with the hybrid filler at the CCB/Fe3O4 ratio of 8/2 exhibited excellent electromagnetic absorption. The composite foam had a higher tensile modulus and higher strength compared to neat foam. The addition of CCB decreased the compression set; however, the compression set was improved by the incorporation of Fe3O4. Composite foams filled with hybrid filler can serve as highly efficient electromagnetic absorbing materials.
Open AccessElectromagnetic Absorption and Mechanical Properties of Natural Rubber Composites Based on Conductive Carbon Black and Fe3O4
In contemporary civilization, the electromagnetic radiation from electronic devices and communication systems has become a substantial pollutant. High-performance electromagnetic absorbers have become a solution for absorbing unwanted electromagnetic waves. This research proposed a lightweight and flexible electromagnetic absorber produced from natural rubber filled with conductive carbon black (CCB) and Fe3O4. The effect of CCB, Fe3O4, and a combination of CCB and Fe3O4 as a hybrid filler on foam morpholog, electromagnetic reflectivity, tensile strength, and compression set properties were investigated. In addition, the effect of the alternating layered structure of CCB and Fe3O4 on electromagnetic absorption was investigated. The results indicated that the composite foam exhibited an interconnected network structure that enhanced the electromagnetic attenuation in the absorber. CCB increased the electromagnetic absorption of the foam, whereas Fe3O4 had less of an effect. The foam filled with the hybrid filler at the CCB/Fe3O4 ratio of 8/2 exhibited excellent electromagnetic absorption. The composite foam had a higher tensile modulus and higher strength compared to neat foam. The addition of CCB decreased the compression set; however, the compression set was improved by the incorporation of Fe3O4. Composite foams filled with hybrid filler can serve as highly efficient electromagnetic absorbing materials.
- Open Access
- 16 May 2022
- Published by Elsevier in Polymer Testing
- Vol. 112
Synthesis and characterization of soft polyurethane for pressure ulcer prevention
- 16 May 2022
- Published by Elsevier in Polymer Testing
- Vol. 112
Open AccessSynthesis and characterization of soft polyurethane for pressure ulcer prevention
- 16 August 2016
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 25 (2) , 323-333
Influence of Crosslinking Agent and Chain Extender on Properties of Gamma-Irradiated PLA
- 16 August 2016
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 25 (2) , 323-333
Influence of Crosslinking Agent and Chain Extender on Properties of Gamma-Irradiated PLA