Vishnu Radhakrishnan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Vishnu Radhakrishnan has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
K. Sudhakar Reddy
Department of Civil Engineering, Indian Institute of Technology, Kharagpur, India
5 shared publications- Aniket Vasantarao Kataware
Indian Institute of Technology Dharwad
2 shared publications G. Surendra Chowdari
Indian Institute of Technology, Kharagpur, India
2 shared publicationsRajib Chattaraj
West Bengal Public Works Department, Kolkata, India
2 shared publications- Shubham Suryawanshi
Indian Institute of Technology Dharwad
2 shared publications Anupam Maity
Indian Institute of Technology, Kharagpur, India
1 shared publication
Latest Publications
- 10 February 2025
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 26 (10) , 2607-2632
Evaluating bonding-debonding properties and moisture susceptibility of chemical-based warm mix asphalt binder and mixes
- 10 February 2025
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 26 (10) , 2607-2632
Evaluating bonding-debonding properties and moisture susceptibility of chemical-based warm mix asphalt binder and mixes
- 13 October 2024
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 101 (8) , 1061-1095
Assessing bonding and debonding properties of Evotherm modified bitumen with natural aggregates using surface free energy approach
- 13 October 2024
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 101 (8) , 1061-1095
Assessing bonding and debonding properties of Evotherm modified bitumen with natural aggregates using surface free energy approach
- 14 September 2018
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 21 (9) , 1035-1043
Sensitivity of rutting and moisture resistance of asphalt mixes to gradation and design air void content
Bituminous mixes are generally designed with gradation and air void content ranges adopted by different agencies. The selected gradation and binder content are permitted to vary within specified tolerance limits. This leads to the possibility of a wide range of mixes with varying mix performance. Thus, it is essential to understand the influence of variation in these parameters on the performance of mixes. The present study aims to examine the sensitivity of the mix performance to variation within the specified gradation and air void ranges. Five aggregate gradations were considered for designing mixes for the volumetric design criterion of 4% air voids. For three of the five gradations, mixes were also designed for two additional design air void contents, 3% and 5%. Rutting resistance of the mixes was measured using a rut tester and moisture resistance was evaluated in terms of Tensile Strength Ratio (TSR). The densification characteristics represented by voids in mineral aggregate (VMA) values of the mixes prepared using the five aggregate gradations are similar to those of the corresponding aggregate packing characteristics (dry aggregate air voids, DAAV). A good relationship was observed between mix rutting and minimum voids in mineral aggregate and DAAV. Sensitivity analysis carried out with different aggregate gradations, design air void contents and tolerances, indicated that rut depth as well as TSR vary over a wide range for the combinations of mixes considered (all within the gradation, air void content and tolerance limits).Compared to the design air void content, aggregate gradation is found to have significantly larger effect on rut depth whereas both gradation and design air void content have similar effect on the TSR value. Using the results obtained from the present investigation, the Indian Marshall mix design criteria (MoRTH 2013) for stability and flow were revisited and new criteria are proposed.
- 14 September 2018
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 21 (9) , 1035-1043
Sensitivity of rutting and moisture resistance of asphalt mixes to gradation and design air void content
Bituminous mixes are generally designed with gradation and air void content ranges adopted by different agencies. The selected gradation and binder content are permitted to vary within specified tolerance limits. This leads to the possibility of a wide range of mixes with varying mix performance. Thus, it is essential to understand the influence of variation in these parameters on the performance of mixes. The present study aims to examine the sensitivity of the mix performance to variation within the specified gradation and air void ranges. Five aggregate gradations were considered for designing mixes for the volumetric design criterion of 4% air voids. For three of the five gradations, mixes were also designed for two additional design air void contents, 3% and 5%. Rutting resistance of the mixes was measured using a rut tester and moisture resistance was evaluated in terms of Tensile Strength Ratio (TSR). The densification characteristics represented by voids in mineral aggregate (VMA) values of the mixes prepared using the five aggregate gradations are similar to those of the corresponding aggregate packing characteristics (dry aggregate air voids, DAAV). A good relationship was observed between mix rutting and minimum voids in mineral aggregate and DAAV. Sensitivity analysis carried out with different aggregate gradations, design air void contents and tolerances, indicated that rut depth as well as TSR vary over a wide range for the combinations of mixes considered (all within the gradation, air void content and tolerance limits).Compared to the design air void content, aggregate gradation is found to have significantly larger effect on rut depth whereas both gradation and design air void content have similar effect on the TSR value. Using the results obtained from the present investigation, the Indian Marshall mix design criteria (MoRTH 2013) for stability and flow were revisited and new criteria are proposed.
- 1 June 2018
- Published by Elsevier in Construction and Building Materials
- Vol. 173, 298-307
Evaluation of asphalt binder rutting parameters
- 1 June 2018
- Published by Elsevier in Construction and Building Materials
- Vol. 173, 298-307
Evaluation of asphalt binder rutting parameters
- 14 September 2017
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 20 (1) , 90-109
Evaluation of wheel tracking and field rutting susceptibility of dense bituminous mixes
Rutting in bituminous layers is a major mode of distress, especially in pavements with thick bituminous layers. Different binder and mix rutting specifications are adopted by agencies worldwide to address the issue of rutting in bituminous mixes. The wheel tracking test is also widely used to evaluate the rutting potential of bituminous layers which depends on the aggregate gradation, binder type and also on the method of mix design adopted. The present study was conducted to examine the relationship between laboratory wheel track rutting and field rutting of different mixes prepared with different aggregate gradations, binder types and binder contents selected using different compaction efforts. Fifteen pavement sections with different surface mixes were constructed on a national highway. Loose bituminous mixes collected from the field were compacted to prepare specimens for wheel tracking tests. Two sets of specimens were prepared to have (a) 7% air voids and (b) an air void content similar to that observed in the field 1 day after construction. The rut depths measured using a wheel tracking machine correlated very well with field rut depths measured after 1 year when the laboratory specimens were prepared at the same initial air void content as achieved in the field. As expected, the rut depth measured in the laboratory wheel tracker for specimens prepared with 7% air voids did not correlate well with 1 year rut depths of field mixes which had different initial air void contents. Limiting wheel tracking test rut depths have been identified on the basis of comparison of the field rutting performance of different mixes and the corresponding laboratory rutting performance of the mixes. Limiting criteria have been proposed for two limiting rut depths of 10 and 20 mm and for different traffic levels.
- 14 September 2017
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 20 (1) , 90-109
Evaluation of wheel tracking and field rutting susceptibility of dense bituminous mixes
Rutting in bituminous layers is a major mode of distress, especially in pavements with thick bituminous layers. Different binder and mix rutting specifications are adopted by agencies worldwide to address the issue of rutting in bituminous mixes. The wheel tracking test is also widely used to evaluate the rutting potential of bituminous layers which depends on the aggregate gradation, binder type and also on the method of mix design adopted. The present study was conducted to examine the relationship between laboratory wheel track rutting and field rutting of different mixes prepared with different aggregate gradations, binder types and binder contents selected using different compaction efforts. Fifteen pavement sections with different surface mixes were constructed on a national highway. Loose bituminous mixes collected from the field were compacted to prepare specimens for wheel tracking tests. Two sets of specimens were prepared to have (a) 7% air voids and (b) an air void content similar to that observed in the field 1 day after construction. The rut depths measured using a wheel tracking machine correlated very well with field rut depths measured after 1 year when the laboratory specimens were prepared at the same initial air void content as achieved in the field. As expected, the rut depth measured in the laboratory wheel tracker for specimens prepared with 7% air voids did not correlate well with 1 year rut depths of field mixes which had different initial air void contents. Limiting wheel tracking test rut depths have been identified on the basis of comparison of the field rutting performance of different mixes and the corresponding laboratory rutting performance of the mixes. Limiting criteria have been proposed for two limiting rut depths of 10 and 20 mm and for different traffic levels.
- 12 September 2017
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 20 (1) , 20-35
Evaluation of rutting potential of asphalts using resilient modulus test parameters
Rutting potential of asphalts can be evaluated in the laboratory by different tests. Any visco-elastic parameter of the mix evaluated at a high pavement temperature can be considered to be a possible parameter to distinguish mixes in terms of their rutting susceptibility. In this study, the potential of the time lag (between load and deformation) observed in a resilient modulus test as an appropriate parameter to explain the rutting resistance of different mixes has been examined. Resilient modulus is a parameter routinely evaluated by many agencies and is used as an input for design and evaluation of pavements. Time lag values were extracted from the resilient modulus test conducted at 35°C and 50°C on asphalt mixes prepared with (a) nine different types of binder and one aggregate gradation and (b) nine different aggregate gradations and with VG30 binder. A wheel tracking test was conducted on the mixes at 60°C. Time lag has been found to be sensitive to bitumen type and aggregate gradation. A strong correlation was observed between the time lag and rut depth measured in the wheel tracking test. It is evident from the present study that time lag measured from the resilient modulus test, which is conducted routinely by many agencies, has the potential to be used as a mix rutting parameter.
- 12 September 2017
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 20 (1) , 20-35
Evaluation of rutting potential of asphalts using resilient modulus test parameters
Rutting potential of asphalts can be evaluated in the laboratory by different tests. Any visco-elastic parameter of the mix evaluated at a high pavement temperature can be considered to be a possible parameter to distinguish mixes in terms of their rutting susceptibility. In this study, the potential of the time lag (between load and deformation) observed in a resilient modulus test as an appropriate parameter to explain the rutting resistance of different mixes has been examined. Resilient modulus is a parameter routinely evaluated by many agencies and is used as an input for design and evaluation of pavements. Time lag values were extracted from the resilient modulus test conducted at 35°C and 50°C on asphalt mixes prepared with (a) nine different types of binder and one aggregate gradation and (b) nine different aggregate gradations and with VG30 binder. A wheel tracking test was conducted on the mixes at 60°C. Time lag has been found to be sensitive to bitumen type and aggregate gradation. A strong correlation was observed between the time lag and rut depth measured in the wheel tracking test. It is evident from the present study that time lag measured from the resilient modulus test, which is conducted routinely by many agencies, has the potential to be used as a mix rutting parameter.
- 6 December 2016
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 19 (3) , 605-623
A predictive model for estimating the viscosity of short-term-aged bitumen
For accurate prediction of pavement performance, it is necessary that the effect of ageing on different mix parameters is accounted for. The short-term- and long-term-aged bitumen viscosities estimated using Global Ageing System (GAS) models are used in the Mechanistic Empirical Pavement Design Guide for the estimation of dynamic modulus. Comparison of the viscosities of the bitumens extracted from field- and laboratory-aged asphalt mixes with the viscosities predicted using the GAS model suggests over-prediction for high temperature and lower bitumen film thickness (FT) combinations and under-prediction for low temperatures and high film thicknesses. That the ageing codes used in the GAS model are not sensitive to FT and temperature also has been established in this study. The new statistical model proposed in this study based on fixed effect regression modelling approach for estimating the short-term-aged bitumen viscosity as a function of bitumen type, FT and temperature has been found to predict the short-term-aged viscosity more accurately compared to the GAS model. The predictions with the new model are particularly better for certain combinations of temperature and FT for which large errors are observed in the predictions made with GAS models. The paper also proposes short-term-ageing conditions (sample weight and exposure time) to be adopted for bitumen in a Rolling Thin Film Oven to simulate the field ageing occurring in asphalt mixes having different film thicknesses.
- 6 December 2016
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 19 (3) , 605-623
A predictive model for estimating the viscosity of short-term-aged bitumen
For accurate prediction of pavement performance, it is necessary that the effect of ageing on different mix parameters is accounted for. The short-term- and long-term-aged bitumen viscosities estimated using Global Ageing System (GAS) models are used in the Mechanistic Empirical Pavement Design Guide for the estimation of dynamic modulus. Comparison of the viscosities of the bitumens extracted from field- and laboratory-aged asphalt mixes with the viscosities predicted using the GAS model suggests over-prediction for high temperature and lower bitumen film thickness (FT) combinations and under-prediction for low temperatures and high film thicknesses. That the ageing codes used in the GAS model are not sensitive to FT and temperature also has been established in this study. The new statistical model proposed in this study based on fixed effect regression modelling approach for estimating the short-term-aged bitumen viscosity as a function of bitumen type, FT and temperature has been found to predict the short-term-aged viscosity more accurately compared to the GAS model. The predictions with the new model are particularly better for certain combinations of temperature and FT for which large errors are observed in the predictions made with GAS models. The paper also proposes short-term-ageing conditions (sample weight and exposure time) to be adopted for bitumen in a Rolling Thin Film Oven to simulate the field ageing occurring in asphalt mixes having different film thicknesses.