F. Paray
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
F. Paray has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
B. Kulunk
Research and Development Center, Timminco Metals, Haley, Ontario, Canada K0J 1Y0
2 shared publicationsJ. E. Gruzleski
Department of Mining and Metallurgical Engineering, McGill University, 3610 University Street, Montreal, PQ, Canada H3A 2B2
2 shared publicationsC. Mercadante
1 shared publicationC.A. Loong
1 shared publicationJ. Gruzleski
1 shared publicationJ.E. Gruzleski
1 shared publication
Latest Publications
- 1 June 2004
- Published by Maney Publishing in International Journal of Cast Metals Research
- Vol. 17 (4) , 193-200
Prediction of microporosity in Al–Si castings in low pressure permanent mould casting using criteria functions
- 1 June 2004
- Published by Maney Publishing in International Journal of Cast Metals Research
- Vol. 17 (4) , 193-200
Prediction of microporosity in Al–Si castings in low pressure permanent mould casting using criteria functions
- 29 November 2000
- Published by Taylor & Francis in International Journal of Cast Metals Research
- Vol. 13 (3) , 147-159
Hot tearing in 319 alloy
To study the effect of strontium on hot tearing in 319 alloy, a special cast iron mould was made to produce a casting with “built-in” restraints that act to create tensile stresses along the length of the casting. Castings with different strontium additions and dissolved hydrogen concentrations were produced and evaluated using a hot tearing index. It was found that strontium has a beneficial effect in reducing hot tearing in 319 alloy. The underlying mechanism is related to the ability of strontium additions to redistribute macroshrinkage as fine internal porosity. The dissolved hydrogen concentration is a critical variable in hot tearing. As the hydrogen level increases, the tendency for hot tearing is reduced.
- 29 November 2000
- Published by Taylor & Francis in International Journal of Cast Metals Research
- Vol. 13 (3) , 147-159
Hot tearing in 319 alloy
To study the effect of strontium on hot tearing in 319 alloy, a special cast iron mould was made to produce a casting with “built-in” restraints that act to create tensile stresses along the length of the casting. Castings with different strontium additions and dissolved hydrogen concentrations were produced and evaluated using a hot tearing index. It was found that strontium has a beneficial effect in reducing hot tearing in 319 alloy. The underlying mechanism is related to the ability of strontium additions to redistribute macroshrinkage as fine internal porosity. The dissolved hydrogen concentration is a critical variable in hot tearing. As the hydrogen level increases, the tendency for hot tearing is reduced.
- 1 April 1996
- Published by Maney Publishing in Materials Science and Technology
- Vol. 12 (4) , 315-322
Effect of strontium on microstructure and properties of aluminium based extrusion alloy 6061
The modifying effect of strontium on the intermetallic phases found in 6061 alloy was investigated in a commercial product. Qualitative and quantitative approaches were used to assess the microstructure. It was shown that strontium altered the platelike β-AlFeSi phase (Al5FeSi) to the Chinese script α-AlFeSi compound (Al8Fe2Si). The influence of the strontium on both the T4 and T6 heat treatments was examined. The use of strontium in 6061 homogenisation allowed reductions in the homogenization time of the alloy as it promoted the formation of the more desirable α-AlFeSi phase in the as cast condition and had no negative effect on the mechanical properties of the end products. MST/3176
- 1 April 1996
- Published by Maney Publishing in Materials Science and Technology
- Vol. 12 (4) , 315-322
Effect of strontium on microstructure and properties of aluminium based extrusion alloy 6061
The modifying effect of strontium on the intermetallic phases found in 6061 alloy was investigated in a commercial product. Qualitative and quantitative approaches were used to assess the microstructure. It was shown that strontium altered the platelike β-AlFeSi phase (Al5FeSi) to the Chinese script α-AlFeSi compound (Al8Fe2Si). The influence of the strontium on both the T4 and T6 heat treatments was examined. The use of strontium in 6061 homogenisation allowed reductions in the homogenization time of the alloy as it promoted the formation of the more desirable α-AlFeSi phase in the as cast condition and had no negative effect on the mechanical properties of the end products. MST/3176
- 1 September 1994
- Published by Maney Publishing in Materials Science and Technology
- Vol. 10 (9) , 757-762
Effect of modification on aluminium matrix of AL–Si–Mg alloys
The influence on the aluminium matrix of chemical modification by addition of strontium or sodium has been investigated in 356 aluminium alloy cast in a permanent mould. Solution heat treatment time and artificial aging time were the two variables examined for the heat treatment study. In the as cast condition, modification does not have an influence on the overall hardness (i.e. that of the aluminium matrix and eutectic silicon) or on the microhardness of the aluminium matrix. Modification does however have an effect on the aluminium matrix of the heat treated alloy. The hardness and yield strength of the modified alloys are lower after the T6 temper compared with the unmodified alloy. Hardness–yield strength relationships have been established. MST/1953
- 1 September 1994
- Published by Maney Publishing in Materials Science and Technology
- Vol. 10 (9) , 757-762
Effect of modification on aluminium matrix of AL–Si–Mg alloys
The influence on the aluminium matrix of chemical modification by addition of strontium or sodium has been investigated in 356 aluminium alloy cast in a permanent mould. Solution heat treatment time and artificial aging time were the two variables examined for the heat treatment study. In the as cast condition, modification does not have an influence on the overall hardness (i.e. that of the aluminium matrix and eutectic silicon) or on the microhardness of the aluminium matrix. Modification does however have an effect on the aluminium matrix of the heat treated alloy. The hardness and yield strength of the modified alloys are lower after the T6 temper compared with the unmodified alloy. Hardness–yield strength relationships have been established. MST/1953