Linhuan Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Linhuan Zhang has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Ruirui Zhang
Intelligent Equipment Research Center, Beijing Academy of Agriculture and Forestry Sciences, Beijing, China
6 shared publications - Tongchuan Yi
Intelligent Equipment Research Center, Beijing Academy of Agriculture and Forestry Sciences, Beijing 100097, China
5 shared publications - Danzhu Zhang
College of Mechano-Electronic Engineering, Gansu Agricultural University, Lanzhou 730070, China
3 shared publications - Liping Chen
College of Mechanical and Electrical Engineering, Gansu Agricultural University, Lanzhou 730070, China
3 shared publications - Longlong Li
Research Center for Intelligent Equipment, Beijing Academy of Agriculture and Forestry Sciences, Beijing 100097, China
2 shared publications - Mingqi Wu
Intelligent Equipment Research Center, Beijing Academy of Agricultural and Forestry Sciences, Beijing 100097, China
2 shared publications
Latest Publications
- Open Access
- 6 March 2025
- Published by MDPI AG in Agriculture
- Vol. 15 (5) , 557
Adaptive Tracking and Cutting Control System for Tea Canopy: Design and Experimental Evaluation
Combined with the characteristic that tea is generally planted in hilly and mountainous areas and considering the existing problems of harvesting with current tea pickers, such as the inability to adjust their posture in real time, poor adaptability to the terrain, insufficient stability, and large differences in the harvesting lengths of tea. To address these issues, an adaptive canopy-following cutting control system has been designed for self-propelled tea harvesters in this study. Specifically, we developed a height-following control algorithm for tea canopy tracking and an adaptive header tilt angle control algorithm based on incremental PID control. Field experiments demonstrated that when the vehicle speed was 0.4 m/s, the height tracking errors for three harvesting lengths (20 mm, 30 mm, and 40 mm) remained within ±5 mm, with correlation coefficients exceeding 0.99. When the height differences between the two sides of the tea ridge were 10 cm, 15 cm, and 20 cm, the maximum uphill roll angles were measured at 1.7°, 2.3°, and 3.0°, respectively, and the time taken for the harvester to return to a horizontal position was around 1.7 s. During downhill movement, the maximum roll angles of the harvester were 1.3°, 2.0°, and 2.6°, respectively, and the time for the harvester to return to a horizontal position was around 2.1 s, demonstrating significant correction effectiveness. Quality assessments revealed that at the 30 mm harvesting length specification, the integrity rate of tea harvesting exceeded 79%, while the missed harvesting rate was below 1.1%. This system effectively enhances harvesting stability and quality, offering novel insights for efficient, high-volume tea production.
- 6 March 2025
- Published by MDPI AG in Agriculture
- Vol. 15 (5) , 557
Open AccessAdaptive Tracking and Cutting Control System for Tea Canopy: Design and Experimental Evaluation
Combined with the characteristic that tea is generally planted in hilly and mountainous areas and considering the existing problems of harvesting with current tea pickers, such as the inability to adjust their posture in real time, poor adaptability to the terrain, insufficient stability, and large differences in the harvesting lengths of tea. To address these issues, an adaptive canopy-following cutting control system has been designed for self-propelled tea harvesters in this study. Specifically, we developed a height-following control algorithm for tea canopy tracking and an adaptive header tilt angle control algorithm based on incremental PID control. Field experiments demonstrated that when the vehicle speed was 0.4 m/s, the height tracking errors for three harvesting lengths (20 mm, 30 mm, and 40 mm) remained within ±5 mm, with correlation coefficients exceeding 0.99. When the height differences between the two sides of the tea ridge were 10 cm, 15 cm, and 20 cm, the maximum uphill roll angles were measured at 1.7°, 2.3°, and 3.0°, respectively, and the time taken for the harvester to return to a horizontal position was around 1.7 s. During downhill movement, the maximum roll angles of the harvester were 1.3°, 2.0°, and 2.6°, respectively, and the time for the harvester to return to a horizontal position was around 2.1 s, demonstrating significant correction effectiveness. Quality assessments revealed that at the 30 mm harvesting length specification, the integrity rate of tea harvesting exceeded 79%, while the missed harvesting rate was below 1.1%. This system effectively enhances harvesting stability and quality, offering novel insights for efficient, high-volume tea production.
- Open Access
- 28 February 2025
- Published by MDPI AG in Electronics
- Vol. 14 (5) , 988
Tea Harvest Robot Navigation Path Generation Algorithm Based on Semantic Segmentation Using a Visual Sensor
During the process of autonomous tea harvesting, it is essential for the tea-harvesting robots to navigate along the tea canopy while obtaining real-time and precise information about these tea canopies. Considering that most tea gardens are located in hilly and mountainous areas, GNSS signals often encounter disturbances, and laser sensors provide insufficient information, which fails to meet the navigation requirements of tea-harvesting robots. This study develops a vision-based semantic segmentation method for the identification of tea canopies and the generation of navigation paths. The proposed CDSC-Deeplabv3+ model integrates a Convnext backbone network with the DenseASP_SP module for feature fusion and a CFF module for enhanced semantic segmentation. The experimental results demonstrate that our proposed CDSC-Deeplabv3+ model achieves mAP, mIoU, F1-score, and FPS metrics of 96.99%, 94.71%, 98.66%, and 5.0, respectively; both the accuracy and speed performance indicators meet the practical requirements outlined in this study. Among the three compared methods for fitting the navigation central line, RANSAC shows superior performance, with minimum average angle deviations of 2.02°, 0.36°, and 0.46° at camera tilt angles of 50°, 45°, and 40°, respectively, validating the effectiveness of our approach in extracting stable tea canopy information and generating navigation paths.
- 28 February 2025
- Published by MDPI AG in Electronics
- Vol. 14 (5) , 988
Open AccessTea Harvest Robot Navigation Path Generation Algorithm Based on Semantic Segmentation Using a Visual Sensor
During the process of autonomous tea harvesting, it is essential for the tea-harvesting robots to navigate along the tea canopy while obtaining real-time and precise information about these tea canopies. Considering that most tea gardens are located in hilly and mountainous areas, GNSS signals often encounter disturbances, and laser sensors provide insufficient information, which fails to meet the navigation requirements of tea-harvesting robots. This study develops a vision-based semantic segmentation method for the identification of tea canopies and the generation of navigation paths. The proposed CDSC-Deeplabv3+ model integrates a Convnext backbone network with the DenseASP_SP module for feature fusion and a CFF module for enhanced semantic segmentation. The experimental results demonstrate that our proposed CDSC-Deeplabv3+ model achieves mAP, mIoU, F1-score, and FPS metrics of 96.99%, 94.71%, 98.66%, and 5.0, respectively; both the accuracy and speed performance indicators meet the practical requirements outlined in this study. Among the three compared methods for fitting the navigation central line, RANSAC shows superior performance, with minimum average angle deviations of 2.02°, 0.36°, and 0.46° at camera tilt angles of 50°, 45°, and 40°, respectively, validating the effectiveness of our approach in extracting stable tea canopy information and generating navigation paths.
- Open Access
UAV-SfM Photogrammetry for Canopy Characterization Toward Unmanned Aerial Spraying Systems Precision Pesticide Application in an Orchard
The development of unmanned aerial spraying systems (UASSs) has significantly transformed pest and disease control methods of crop plants. Precisely adjusting pesticide application rates based on the target conditions is an effective method to improve pesticide use efficiency. In orchard spraying, the structural characteristics of the canopy are crucial for guiding the pesticide application system to adjust spraying parameters. This study selected mango trees as the research sample and evaluated the differences between UAV aerial photography with a Structure from Motion (SfM) algorithm and airborne LiDAR in the results of extracting canopy parameters. The maximum canopy height, canopy projection area, and canopy volume parameters were extracted from the canopy height model of SfM () and the canopy height model of LiDAR () by grids with the same width as the planting rows (5.0 m) and 14 different heights (0.2 m, 0.3 m, 0.4 m, 0.5 m, 0.6 m, 0.8 m, 1.0 m, 2.0 m, 3.0 m, 4.0 m, 5.0 m, 6.0 m, 8.0 m, and 10.0 m), respectively. Linear regression equations were used to fit the canopy parameters obtained from different sensors. The correlation was evaluated using and , and a t-test (α = 0.05) was employed to assess the significance of the differences. The results show that as the grid height increases, the values for the maximum canopy height, projection area, and canopy volume extracted from and increase, while the values decrease. When the grid height is 10.0 m, the for the maximum canopy height extracted from the two models is , with an of . For the canopy projection area, the is 97.83%, with an of 0.01, and for the canopy volume, the is 98.35%, with an of 0.0337. When the grid height exceeds 1.0 m, the t-test results for the three parameters are all greater than 0.05, accepting the hypothesis that there is no significant difference in the canopy parameters obtained by the two sensors. Additionally, using the coordinates of the intersection of the linear regression equation and as a reference, tends to overestimate lower canopy maximum height and projection area, and underestimate higher canopy maximum height and projection area compared to . This to some extent reflects that the surface of is smoother. This study demonstrates the effectiveness of extracting canopy parameters to guide UASS systems for variable-rate spraying based on UAV oblique photography combined with the SfM algorithm.Open AccessUAV-SfM Photogrammetry for Canopy Characterization Toward Unmanned Aerial Spraying Systems Precision Pesticide Application in an Orchard
The development of unmanned aerial spraying systems (UASSs) has significantly transformed pest and disease control methods of crop plants. Precisely adjusting pesticide application rates based on the target conditions is an effective method to improve pesticide use efficiency. In orchard spraying, the structural characteristics of the canopy are crucial for guiding the pesticide application system to adjust spraying parameters. This study selected mango trees as the research sample and evaluated the differences between UAV aerial photography with a Structure from Motion (SfM) algorithm and airborne LiDAR in the results of extracting canopy parameters. The maximum canopy height, canopy projection area, and canopy volume parameters were extracted from the canopy height model of SfM () and the canopy height model of LiDAR () by grids with the same width as the planting rows (5.0 m) and 14 different heights (0.2 m, 0.3 m, 0.4 m, 0.5 m, 0.6 m, 0.8 m, 1.0 m, 2.0 m, 3.0 m, 4.0 m, 5.0 m, 6.0 m, 8.0 m, and 10.0 m), respectively. Linear regression equations were used to fit the canopy parameters obtained from different sensors. The correlation was evaluated using and , and a t-test (α = 0.05) was employed to assess the significance of the differences. The results show that as the grid height increases, the values for the maximum canopy height, projection area, and canopy volume extracted from and increase, while the values decrease. When the grid height is 10.0 m, the for the maximum canopy height extracted from the two models is , with an of . For the canopy projection area, the is 97.83%, with an of 0.01, and for the canopy volume, the is 98.35%, with an of 0.0337. When the grid height exceeds 1.0 m, the t-test results for the three parameters are all greater than 0.05, accepting the hypothesis that there is no significant difference in the canopy parameters obtained by the two sensors. Additionally, using the coordinates of the intersection of the linear regression equation and as a reference, tends to overestimate lower canopy maximum height and projection area, and underestimate higher canopy maximum height and projection area compared to . This to some extent reflects that the surface of is smoother. This study demonstrates the effectiveness of extracting canopy parameters to guide UASS systems for variable-rate spraying based on UAV oblique photography combined with the SfM algorithm. - Open Access
Optimization Design and Experimental Study of Solid Particle Spreader for Unmanned Aerial Vehicle
This study designed and investigated a solid particle spreader, as well as parameter optimization and experimental for a groove wheel, to mitigate the problems of low uniformity and poor control accuracy of solid particulate material UAV spreading. The discrete element method was used to simulate and analyze the displacement range and stability of each grooved wheel at low speeds. Furthermore, orthogonal regression and response surface analyses were used to analyze the influence of each factor on the stability of the discharge rate and pulsation amplitude. The results showed that the helix angle, sharpness, and length of the groove significantly influenced the application performance, whereas the number of grooves had no significant influence. The groove shape was eccentric, the helix angle was 50°, the length was 35 mm, and the number of grooves was 7. Additionally, the bench test results showed that in the range of 10–60 rpm, the relative deviation of the discharging rate between the simulation and bench test is from 0.47% to 10.39%, and the average relative deviation is 3.93%. Between the groove wheel rotation speed and discharge rate, R2 was 0.991, and the adjustable range of the discharge amount was between 3.68 and 23.43 g/s. The minimum and maximum variation coefficients of the average discharge rate among individual applicators were 1.01% and 2.79%, respectively, whereas the standard deviations were 0.09 and 0.46 g/s, respectively. In conclusion, the discharge stability and adjustable range of the spreader using the optimized groove wheel satisfied the requirements for solid particulate material discharge.
Open AccessOptimization Design and Experimental Study of Solid Particle Spreader for Unmanned Aerial Vehicle
This study designed and investigated a solid particle spreader, as well as parameter optimization and experimental for a groove wheel, to mitigate the problems of low uniformity and poor control accuracy of solid particulate material UAV spreading. The discrete element method was used to simulate and analyze the displacement range and stability of each grooved wheel at low speeds. Furthermore, orthogonal regression and response surface analyses were used to analyze the influence of each factor on the stability of the discharge rate and pulsation amplitude. The results showed that the helix angle, sharpness, and length of the groove significantly influenced the application performance, whereas the number of grooves had no significant influence. The groove shape was eccentric, the helix angle was 50°, the length was 35 mm, and the number of grooves was 7. Additionally, the bench test results showed that in the range of 10–60 rpm, the relative deviation of the discharging rate between the simulation and bench test is from 0.47% to 10.39%, and the average relative deviation is 3.93%. Between the groove wheel rotation speed and discharge rate, R2 was 0.991, and the adjustable range of the discharge amount was between 3.68 and 23.43 g/s. The minimum and maximum variation coefficients of the average discharge rate among individual applicators were 1.01% and 2.79%, respectively, whereas the standard deviations were 0.09 and 0.46 g/s, respectively. In conclusion, the discharge stability and adjustable range of the spreader using the optimized groove wheel satisfied the requirements for solid particulate material discharge.
- Open Access
- 24 February 2024
- Published by MDPI AG in Agriculture
- Vol. 14 (3) , 364
Research on Individual Tree Canopy Segmentation of Camellia oleifera Based on a UAV-LiDAR System
In consideration of the limited accuracy of individual tree canopy segmentation algorithms due to the diverse canopy structure and complex environments in mountainous and hilly areas, this study optimized the segmentation parameters of three algorithms for individual tree canopy segmentation of Camellia oleifera in such environments by analyzing their respective parameters. Utilizing an Unmanned Aerial Vehicle-Light Detecting and Ranging (UAV-LiDAR) system, we obtained Canopy Height Models (CHM) of Camellia oleifera canopies based on Digital Elevation Models (DEM) and Digital Surface Models (DSM). Subsequently, we investigated the effects of CHM segmentation, point cloud clustering segmentation, and layer stacking fitting segmentation on Camellia oleifera canopies across different research areas. Additionally, combining ground survey data from forest lands with visual interpretation of UAV orthophoto images, we evaluated the performance of these three segmentation algorithms in terms of the F-score as an evaluation indicator for individual tree canopy segmentation accuracy. Combined with the Cloth Simulation Filter (CSF) filtering algorithm after removing the ground point cloud, our findings indicate that among different camellia densities and terrain environments, the point cloud clustering segmentation algorithm achieved the highest segmentation accuracy at 93%, followed by CHM segmentation at 88% and the layer stacking fitting segmentation method at 84%. By analyzing the data from UAV-LiDAR technology involving various land and Camellia oleifera planting types, we verified the applicability of these three segmentation algorithms for extracting camellia canopies. In conclusion, this study holds significant importance for accurately delineating camellia canopies within mountainous hilly environments while providing valuable insights for further research in related fields.
- 24 February 2024
- Published by MDPI AG in Agriculture
- Vol. 14 (3) , 364
Open AccessResearch on Individual Tree Canopy Segmentation of Camellia oleifera Based on a UAV-LiDAR System
In consideration of the limited accuracy of individual tree canopy segmentation algorithms due to the diverse canopy structure and complex environments in mountainous and hilly areas, this study optimized the segmentation parameters of three algorithms for individual tree canopy segmentation of Camellia oleifera in such environments by analyzing their respective parameters. Utilizing an Unmanned Aerial Vehicle-Light Detecting and Ranging (UAV-LiDAR) system, we obtained Canopy Height Models (CHM) of Camellia oleifera canopies based on Digital Elevation Models (DEM) and Digital Surface Models (DSM). Subsequently, we investigated the effects of CHM segmentation, point cloud clustering segmentation, and layer stacking fitting segmentation on Camellia oleifera canopies across different research areas. Additionally, combining ground survey data from forest lands with visual interpretation of UAV orthophoto images, we evaluated the performance of these three segmentation algorithms in terms of the F-score as an evaluation indicator for individual tree canopy segmentation accuracy. Combined with the Cloth Simulation Filter (CSF) filtering algorithm after removing the ground point cloud, our findings indicate that among different camellia densities and terrain environments, the point cloud clustering segmentation algorithm achieved the highest segmentation accuracy at 93%, followed by CHM segmentation at 88% and the layer stacking fitting segmentation method at 84%. By analyzing the data from UAV-LiDAR technology involving various land and Camellia oleifera planting types, we verified the applicability of these three segmentation algorithms for extracting camellia canopies. In conclusion, this study holds significant importance for accurately delineating camellia canopies within mountainous hilly environments while providing valuable insights for further research in related fields.
- Open Access
- 1 January 2021
- Published by International Journal of Agricultural and Biological Engineering (IJABE) in International Journal of Agricultural and Biological Engineering
- Vol. 14 (5) , 19-26
Development of sensor system for real-time measurement of droplet deposition of agricultural sprayers
During the chemical application process, droplet deposition on a target is an important reference indicator for evaluating the spraying technique and its performance. In order to quickly obtain deposition results in the field, this study proposed a novel system based on surface humidity sensors. The basic principle is to convert the measured physical quantity change into a capacitance change, thereby realizing the physical quantity to electrical signal conversion. An Android application for mobile terminal and corresponding coordinator were developed, which allowed operators to control multiple sensors simultaneously through the Bluetooth. The soluble tracer detected by spectrophotometer was used to calibrate the system. The obtained results indicated a good correlation between deposition volume and voltage increment output from the newly system (R2 of the six nozzles with Dv0.5 ranging from 107.28 μm to 396.20 μm were 0.8674-0.9729), and a power regression model based on the least squares technique (R2=0.8022) was developed. In the field test, the system exhibited an optimal performance in predicting the deposition volume. Compared with the conventional method of measuring tracer concentration, the deviation was less than 10%. In addition, the system exhibited good fitting curve of the deposition distribution with droplet number results measured by the water sensitive paper method. Keywords: deposition measurement, agricultural sprayer, droplets, intelligent sensor DOI: 10.25165/j.ijabe.20211405.5528 Citation: Li L L, Zhang R R, Chen L P, Yi T C, Xu G, Xue D X, et al. Development of sensor system for real-time measurement of droplet deposition of agricultural sprayers. Int J Agric & Biol Eng, 2021; 14(5): 19–26.
- 1 January 2021
- Published by International Journal of Agricultural and Biological Engineering (IJABE) in International Journal of Agricultural and Biological Engineering
- Vol. 14 (5) , 19-26
Open AccessDevelopment of sensor system for real-time measurement of droplet deposition of agricultural sprayers
During the chemical application process, droplet deposition on a target is an important reference indicator for evaluating the spraying technique and its performance. In order to quickly obtain deposition results in the field, this study proposed a novel system based on surface humidity sensors. The basic principle is to convert the measured physical quantity change into a capacitance change, thereby realizing the physical quantity to electrical signal conversion. An Android application for mobile terminal and corresponding coordinator were developed, which allowed operators to control multiple sensors simultaneously through the Bluetooth. The soluble tracer detected by spectrophotometer was used to calibrate the system. The obtained results indicated a good correlation between deposition volume and voltage increment output from the newly system (R2 of the six nozzles with Dv0.5 ranging from 107.28 μm to 396.20 μm were 0.8674-0.9729), and a power regression model based on the least squares technique (R2=0.8022) was developed. In the field test, the system exhibited an optimal performance in predicting the deposition volume. Compared with the conventional method of measuring tracer concentration, the deviation was less than 10%. In addition, the system exhibited good fitting curve of the deposition distribution with droplet number results measured by the water sensitive paper method. Keywords: deposition measurement, agricultural sprayer, droplets, intelligent sensor DOI: 10.25165/j.ijabe.20211405.5528 Citation: Li L L, Zhang R R, Chen L P, Yi T C, Xu G, Xue D X, et al. Development of sensor system for real-time measurement of droplet deposition of agricultural sprayers. Int J Agric & Biol Eng, 2021; 14(5): 19–26.
- Open Access
- 31 October 2017
- Published by DEStech Publications in DEStech Transactions on Computer Science and Engineering
- No. aiea
Compressive Sensing and Reconstruction of Crop Growth Environmental Information
The crop growth environmental information in farmland such as temperature and humidity has a gentle variation amplitude in a certain time or space domain, and is sparse in the discrete cosine transform domain. Based on compression sensing, we construct the approach to crop growth environmental information monitoring. The reconstruction error for crop growth environmental information is validated through the simulation experiment. By exploiting orthogonal matching pursuit method, it is found that the reconstructed environmental information data are consistent with the measured data.
- 31 October 2017
- Published by DEStech Publications in DEStech Transactions on Computer Science and Engineering
- No. aiea
Open AccessCompressive Sensing and Reconstruction of Crop Growth Environmental Information
The crop growth environmental information in farmland such as temperature and humidity has a gentle variation amplitude in a certain time or space domain, and is sparse in the discrete cosine transform domain. Based on compression sensing, we construct the approach to crop growth environmental information monitoring. The reconstruction error for crop growth environmental information is validated through the simulation experiment. By exploiting orthogonal matching pursuit method, it is found that the reconstructed environmental information data are consistent with the measured data.