ZCZinour Charifoulline

Zinour Charifoulline

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Zinour Charifoulline has a total of 95 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Improving the Accuracy of the LHC Superconducting Main Dipole Circuit By-Pass Diode Model Through Closed-Loop Optimization

    by M. Gorenflo, Z. Charifoulline, A. Chmielinska, E. Ravaioli, A. Verweij, A. Vitrano, M. Wozniak

    The Large Hadron Collider (LHC) includes eight main dipole circuits, each containing 154 superconducting magnets. We are carrying out simulations of the electromagnetic thermal behavior of these circuits, together with experimental tests and continuous monitoring, to ensure their safe operation and to further improve our understanding. Accurately modeling these eight circuits is very challenging. This is due to the interactions between the 154 magnets in each circuit and due to small variations in the physical properties of the magnets, e.g. due to component tolerances which introduce numerous unknown parameters into the model. In this contribution, we propose a method to optimize these large parameter sets efficiently, using a novel software module that combines our previously in-house developed circuit simulation framework with Dakota, an open-source parameter optimization toolkit. We demonstrate the effectiveness of this approach by optimizing a new simulation model of the dipole magnet by-pass diodes. Improving the accuracy of the model may in the future allow the identification of magnets and circuit components with non-conform behavior, and the reconstruction of failure cases for which no measurement data are available.

  • Open Access

    Interpretable Anomaly Detection in the LHC Main Dipole Circuits With Nonnegative Matrix Factorization

    by Christoph Obermair, Andrea Apollonio, Zinour Charifoulline, Lukas Felsberger, Marvin Janitschke, Franz Pernkopf, Emmanuele Ravaioli, Arjan Verweij, Daniel Wollmann, Mariusz Wozniak

    CERN's Large Hadron Collider (LHC), with its eight superconducting main dipole circuits, has been in operation for over a decade. During this time, relevant operational parameters of the circuits, including circuit current, voltages across magnets and their coils, and current to ground, have been recorded. These data allow for a comprehensive analysis of the circuit characteristics, the interaction between their components, and their variation over time. Such insights are essential to understand the state of health of the circuits and to detect and react to hardware fatigue and degradation at an early stage. In this work, a systematic approach is presented to better understand the behavior of the main LHC dipole circuits following fast power aborts. Nonnegative matrix factorization is used to model the recorded frequency spectra as common subspectra by decomposing the recorded data as a linear combination of basis vectors, which are then related to hardware properties. The loss in reconstructing the recorded frequency spectra allows to distinguish between normal and abnormal magnet behavior. In the case of abnormal behavior, the analysis of the subspectra properties enables to infer possible hardware issues. Following this approach, five dipole magnets with abnormal behavior were identified, of which one was confirmed to be damaged. As three of the other four identified magnets share similar subspectra characteristics, they are also treated as potentially critical. These results are essential for preparing targeted magnet measurements and may lead to preventive replacements.


  • Performance of the Large Hadron Collider's Cryogenic Bypass Diodes Over the First Two Physics Runs, Future Projects, and Perspectives

    by Giorgio D'ANgelo, Zinour Charifoulline, Reiner Denz, Mathieu Favre, Dietrich Hagedorn, Arnaud Monteuuis, Felix Rodriguez-Mateos, Andrzej Siemko, Krzysztof Stachon, Arjan Verweij, et al.

    Cryogenic bypass diodes have been installed in all superconducting dipole magnets (1232) and quadrupole magnets (392) of the Large Hadron Collider (LHC) at CERN, and operated during the physics runs since 2009. The bypass diodes are a fundamental ingredient of the quench protection system for those main dipoles and quadrupoles magnets. The diodes are located inside the magnet cryostats, operating in superfluid helium and exposed to ionizing radiation. The connection between the superconducting magnet and the bypass diode is made through a mechanical clamping system and copper bus bars. Since their first installation, all LHC diodes have undergone at least two full thermal cycles (from 1.9 K to room temperature and back to superfluid helium temperature). The evolution of electrical parameters as well as improvements and modifications made over a period of 10 years are reviewed in this paper. With CERN preparing for LHC's High Luminosity era, the long-term strategy for cold diodes is presented, based on the overall results and experience gathered so far, including the studies related to the tolerance with respect to the radiation doses and neutron fluences expected.


  • Resistance of Splices in the LHC Main Superconducting Magnet Circuits at 1.9 K

    by Zinour Charifoulline, Mateusz Jakub Bednarek, Reiner Denz, Sandrine Le Naour, Christian Scheuerlein, Andrzej Siemko, Jens Steckert, Jean-Philippe Tock, Arjan Verweij, Markus Zerlauth

    The electrical interconnections between the LHC main magnets are made of soldered joints (splices) of two super-conducting Rutherford cables, stabilized by a copper busbar. In 2009, a number of splices were found not properly stabilized and could have suffered a thermal runaway in case of quench at high current. The LHC was therefore operated at reduced energy and all joints were continuously monitored by a newly installed layer of the Quench Protection System (nQPS). During the first Long Shutdown (LS1) in 2013/14 the high-current busbar joints were consolidated to allow a safe operation of the LHC at its design energy, i.e. 14 TeV center-of-mass. The SMACC project (Super-conducting Magnets And Circuits Consolidation) has coordinated the consolidation of the 10306 13 kA busbar splices. Since 2015, the LHC is successfully operated at an energy of 13 TeV center-of-mass. This paper will briefly describe the applied analysis method and will present the results and comparisons of the Rutherford-cable splice resistance measurements at 1.9 K before and after LS1, based on an unprecedented amount of information gathered during long-term operation of superconducting high-current joints. A few outliers that are still present after the splice consolidation will also be shortly discussed.


  • A Statistical Analysis of Electrical Faults in the LHC Superconducting Magnets and Circuits

    by Luca Bottura, Jean-Philippe Tock, Bernard Auchmann, Mateusz Bednarek, Daniel Calcoen, Zinour Charifoulline, Gert-Jan Coelingh, Giorgio D'ANgelo, Per Hagen, Sandrine Le Naour, et al.

    The large hadron collider (LHC) at CERN has been operating and generating physics experimental data since September 2008, and following its first long shut down, it has entered a second, 4-year-long physics run. It is to date the largest superconducting installation ever built, counting over 9000 magnets along its 27-km long circumference. A significant operational experience has been accumulated, including the occurrence and consequences of electrical faults at the level of the superconducting magnets, as well as their protection and instrumentation circuits. The purpose of this paper is to provide a first overview of the most common electrical faults and their frequency of occurrence in the first years of operation, and to perform a statistical analysis that can provide reference values for future productions of similar dimensions and nature.


  • Overview of the Performance of Quench Heaters for High-Current LHC Superconducting Magnets

    by Zinour Charifoulline, Lorenzo Bortot, Reiner Denz, Felix Rodriguez Mateos, Andrzej Siemko, Jens Steckert, Arjan Verweij, Gerard Willering

    Quench heaters are an essential part of the protection of all high-current large hadron collider (LHC) superconducting circuits. About 2000 dipole and quadrupole magnets are equipped with quench heaters in order to protect them against development of excessive voltage and overheating after a resistive transition. The quench heaters are made of stainless steel foil partially plated with copper and connected to 900 V capacitor bank discharge power supplies. During Hardware Commissioning campaigns and machine operation every quench heater discharge event is carefully analysed to detect a possible failure or a precursor of a failure, which could lead to damage of the heater or to the superconducting coils in subsequent discharges. This paper will briefly describe two different ways of quench heater data analysis and will present the heaters performance during the years 2008-2015. A summary of the quench heater fatigue test performed on a spare LHC main dipole magnet will also be given.


  • Performance of CERN LHC Main Dipole Magnets on the Test Bench From 2008 to 2016

    by G. P. Willering, M. Bajko, L. Bottura, Z. Charifoulline, M. Charrondiere, G. D'ANgelo, G. Dib, O. Ditsch, P. Hagen, S. Le Naour, et al.

    Throughout 2015 and 2016, the LHC is operated with a current in the main dipoles of 10980 A, equivalent to a proton-proton collision energy of 13 TeV in the center of mass. A total of 175 training quenches were needed in 2014 in the 1232 main dipole magnets installed in the LHC at CERN to reach operational conditions. Since 2008, a number of dipole magnets have been removed from the LHC and were, sometimes after repairs of nonconformities, retested in the CERN based SM18 magnet test facility up to ultimate current. Other magnets have been retested after long storage. The results confirm earlier findings that some magnets series are more prone to quenching than others after thermal cycle. The correlation between a short and long thermal cycle is under investigation. Special cases with many thermal cycles will be highlighted and a new magnet series, fully produced at CERN is introduced. Results of a quench heater fatigue test, assessing the long-term reliability of the quench heaters, will be given. The results of repairs following high internal splice resistances are discussed.


  • Retraining of the 1232 Main Dipole Magnets in the LHC

    by A. Verweij, B. Auchmann, M. Bednarek, L. Bottura, Z. Charifoulline, S. Feher, P. Hagen, M. Modena, S. Le Naour, I. Romera, et al.

    The Large Hadron Collider (LHC) contains eight main dipole circuits, each of them with 154 dipole magnets powered in series. These 15-m-long magnets are wound from Nb-Ti superconducting Rutherford cables, and have active quench detection triggering heaters to quickly force the transition of the coil to the normal conducting state in case of a quench, and hence reduce the hot spot temperature. During the reception tests in 2002-2007, all these magnets have been trained up to at least 12 kA, corresponding to a beam energy of 7.1 TeV. After installation in the accelerator, the circuits have been operated at reduced currents of up to 6.8 kA, from 2010 to 2013, corresponding to a beam energy of 4 TeV. After the first long shutdown of 2013-2014, the LHC runs at 6.5 TeV, requiring a dipole magnet current of 11.0 kA. A significant number of training quenches were needed to bring the 1232 magnets up to this current. In this paper, the circuit behavior in case of a quench is presented, as well as the quench training as compared to the initial training during the reception tests of the individual magnets.


  • Open Access

    Performance of the cold powered diodes and diode leads in the main magnets of the LHC

    by G P Willering, C Giloux, M Bajko, M Bednarek, L Bottura, Z Charifoulline, K Dahlerup-Petersen, G Dib, G D'Angelo, A Gharib, et al.

    During quench tests in 2011 variations in resistance of an order of magnitude were found in the diode by-pass circuit of the main LHC magnets. An investigation campaign was started to understand the source, the occurrence and the impact of the high resistances. Many tests were performed offline in the SM18 test facility with a focus on the contact resistance of the diode to heat sink contact and the diode wafer temperature. In 2014 the performance of the diodes and diode leads of the main dipole bypass systems in the LHC was assessed during a high current qualification test. In the test a current cycle similar to a magnet circuit discharge from 11 kA with a time constant of 100 s was performed. Resistances of up to 600 μΩ have been found in the diode leads at intermediate current, but in general the high resistances decrease at higher current levels and no sign of overheating of diodes has been seen and the bypass circuit passed the test. In this report the performance of the diodes and in particular the contact resistances in the diode leads are analysed with available data acquired over more than 10 years from acceptance test until the main dipole training campaign in the LHC in 2015.