SISergiu Ilie

Sergiu Ilie

*This is an algorithmically generated author record based on publicly available information.

Sergiu Ilie has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Evolution of non-metallic inclusions in an Al-killed, Ca-treated, low-S steel during industrial secondary refining

    by Robert Musi, Kathrin Thiele, Sergiu Ilie, Roman Rössler, Susanne Katharina Michelic

    The evolution of non-metallic inclusions during secondary refining of an Al-killed, Ca-treated, low-S steel was characterized at eight stages from deoxidation to the tundish. Automated SEM–EDS analysis was applied down to an equivalent circle diameter of 0.5 μm. The modification path proceeded from alumina via spinel to Ca-aluminates. Ca-treatment affected the pre-existing oxides differently: within approximately 85 s of CaSi wire injection, the spinel inclusions were consumed, whereas a small alumina population persisted. A predominantly submicroscopic, transient CaO–CaS population formed and converted to Ca-aluminates within minutes, with the CaS component consumed preferentially. During subsequent ladle holding, reoxidation generated new Ca-poor spinel and alumina alongside the modified inclusions, as the Ca fade progressed from 32 to 17 ppm. Between the final ladle sample and the tundish, the mean number density decreased from 291.4 to 96.4 mm - ², the size distributions shifted toward larger diameters in every heat, and the total O content decreased from 29 to 13 ppm, indicating agglomeration-assisted removal. Despite differences during treatment, all four heats converged at the tundish, centered on the low-melting 12CaO·7Al 2 O 3 composition. For the investigated steel and process route, tundish samples therefore provide a reliable basis for cleanness assessment, whereas single ladle samples may not be representative.

  • Open Access

    Process Chain Sensitivities in Green Steel Production: Tramp Element Impacts on Casting and Reheating

    by Georg Gaiser, Robert Littringer, Peter Presoly, Christian Bernhard, Sergiu Ilie

    Surface defects are a critical indicator of semi-finished product quality, with the elements Cu and Sn exerting a significant influence through the phenomenon known as hot shortness. The present study quantifies the defect sensitivity caused by Cu and Sn for three different steel grades under continuous casting conditions using the In-situ Material Characterization by Bending (IMC-B) test. Building on this, purposefully pre-damaged samples were subjected to reheating under process-related conditions within a natural-gas combustion atmosphere. The objective is to investigate how surface defects from the casting process evolve depending on their initial depth and the selected final reheating temperature. Finally, metallographic analyses allow for a correlation between the initial defect depth and the surface morphology after reheating.


  • Open Access

    Identification of inclusion sources by slag tracers during the ladle change operation

    by Christoph Truschner, Sergiu Ilie, Alfred Jungreithmeier, Susanne K. Michelic

    The cleanness of steel is significantly influenced by the casting conditions during continuous slab casting. Unsteady casting conditions, such as those occurring during a ladle change, may deteriorate the cleanness of the cast product but are process-wise unavoidable. This study investigates the impact of ladle change operation on meso- and macroscopic cleanness levels and seeks to uncover the origin of these non-metallic inclusions (NMIs). To facilitate the identification of the particles’ source, slag tracers were employed to mark ladle and tundish slag. Hot-rolled coils produced from slabs cast during the ladle change were sampled along their entire length and characterised for meso- and macro-NMIs. The inclusions’ positions were then projected to the corresponding positions within the initial strand. The ladle change event significantly deteriorated the strand's meso- and macro-cleanness over a total casting length of approximately 19 m. During the period, as the tundish weight decreased, the largest inclusions were detected. The highest concentration of meso- and macro-NMIs was observed shortly before the start of casting of the subsequent heat. The following sources for meso- and macroscopic NMIs were determined during the ladle change: ladle slag, mould slag and eroded refractory material.

  • Open Access

    Scaling Behavior and Surface Quality of High-Strength Low-Alloy Steels with Higher Levels on Cu, Sn, and Ni Under Slab Reheating Conditions

    by Georg Gaiser, Peter Presoly, Christian Bernhard, Sergiu Ilie

    Nowadays the production of steel from scrap in electric arc furnaces is the most common bridging technology to reduce CO2 emissions. Depending on scrap quality, a non-negligible content of tramp elements such as Cu, Sn, or Ni is introduced into the steel. As their affinity to oxygen is lower than that of iron, they typically enrich at the steel/scale interface area and along grain boundaries during oxidation, which may result in quality problems. Oxidation processes are unavoidable in solid steel processing, and therefore, a deeper understanding of the occurring phenomena, such as intergranular oxidation and liquid metal infiltration of grain boundaries, is essential to continuously improve the product quality. In this study, oxidation experiments for slab reheating were performed by simultaneous thermal analysis under near-process conditions. For a clear statement on the role of tramp elements during oxidation, steel grades with and without tramp elements were investigated. The addition of the expected future contents of Cu and Sn does not affect external oxidation, but at the interface the presence of Cu and Sn leads to the formation of liquid Cu phases and infiltration of grain boundaries. The additional presence of Ni counteracts this formation, but due to its huge impact on iron activity it favors the formation of a rough steel/scale interface. In contrast with Ni, Cu and Sn hardly have any influence on iron activity. Numerical calculations based on a diffusion model and results of the well-known thermochemical software FactSage confirm these effects.


  • Open Access

    Investigating the Origin of Non-Metallic Inclusions in Ti-Stabilized ULC Steels Using Different Tracing Techniques

    by Kathrin Thiele, Christoph Truschner, Christoph Walkner, Thomas C. Meisel, Sergiu Ilie, Roman Rössler, Susanne K. Michelic

    Since steel cleanness comes to the fore of steel producers worldwide, it is necessary to understand the formation mechanism and modification of non-metallic inclusions (NMIs) in more detail. One central point is the identification of the source of especially interfering NMIs to prevent their evolution in the future. The present study applies two approaches to determine the source of NMIs in Ti-stabilized ultra-low carbon (ULC) steels—the active and the passive tracing. Both approaches are applied to an industrial experiment. The active tracing technique is focused on investigating the clogging layer formation in submerged entry nozzles and, hence, the origin of alumina particles. This method adds rare earth elements (REEs) directly to the melt to mark pre-existing deoxidation products at a certain point of the steelmaking process. The main concern of the passive method, the so-called REE fingerprint, is the determination of the source of mesoscopic NMIs. For the REE fingerprint, the pre-existing concentration of REEs in different potential sources and the investigated NMIs are measured by using an inductively coupled plasma mass spectrometer (ICP-MS). The resulting patterns are compared after normalizing the contents to chondrites, and the NMIs’ origins are identified. Concerning the EDS analysis and the resulting patterns from the REE fingerprint, the mold slag and, respectively, the casting powder were the sources of the investigated NMIs.


  • Open Access

    Tracing of Deoxidation Products in Ti‐Stabilized Interstitial Free Steels by La and Ce on an Industrial and Laboratory Scale

    by Christoph Truschner, Kathrin Thiele, Sergiu Ilie, Roman Rössler, Alfred Jungreithmeier, Susanne K. Michelic

    The continuous casting of Al-killed Ti-stabilized interstitial free steels is often affected by clogging. By today, the mechanism behind this phenomenon is not entirely clarified. The active tracing method, which involves the direct addition of rare-earth elements (REEs), enables tracking of nonmetallic inclusions (NMIs) over process time. Due to the high oxygen affinity of these elements, preexisting NMIs are partially reduced and marked by this tracer. Using scanning electron microscopy with energy-dispersive spectroscopy, it is possible to differentiate such labeled NMIs from particles formed at later stages in the process by the absence of these tracing elements. Active tracing is used in industrial and laboratory settings to trace preexisting alumina NMIs with La or Ce. In the investigation, it is revealed that the number of small NMIs increases after the addition of REEs, and subsequently, the size increases again after FeTi is alloyed. In both settings, traced and untraced Al–Ti oxides are found. The separation tendency of traced NMIs is studied over time by analyzing the composition of the slags. Furthermore, the impact of deoxidation products on the formation of the clogging layer within the submerged entry nozzle is investigated, indicating that these NMIs contribute to its formation.


  • Open Access

    Untersuchung der Performance eines fluorfreien Gießpulvers auf einer Pilotanlage

    by Selina Riedler, Nathalie Gruber, Irmtraud Marschall, Viorel-Sergiu Ilie, Gerald Klösch

  • Open Access

    Thermomechanical and Microstructural Analysis of the Influence of B- and Ti-Content on the Hot Ductility Behavior of Microalloyed Steels

    by Marina Gontijo, Arnab Chakraborty, Richard F. Webster, Sergiu Ilie, Jakob Six, Sophie Primig, Christof Sommitsch

    The effects of the combined addition of B and Ti, as well as the influence of different strain rates on the hot ductility behavior of low carbon, continuously cast, microalloyed steels were investigated in this work. Tensile tests, microstructure analyses, and thermokinetic simulations were performed with in situ melted samples. Furthermore, prior austenite grain evaluations were carried out for the two different microalloyed steels. Increasing the strain rate brought improvements to the ductility, which was more significant in the steel with the leanest composition. The steel containing more B and Ti presented a better hot ductility behavior under all conditions tested. The main causes for the improvements rely on the precipitation behavior and the austenite–ferrite phase transformation. The preferential formation of TiN instead of fine BN and AlN was seen to be beneficial to the ductility, as well as the absence of MnS. Grain boundary segregation of free B that did not form BN retarded the ferrite formation, avoiding the brittleness brought by the thin ferrite films at the austenite grain boundaries. Furthermore, it was revealed that for the steels in question, the prior austenite grains have less influence on the hot ductility behavior than the precipitates and ferrite formation.


  • Open Access

    Comparison of Hot Ductility Behavior of microAlloyed Steels with Different B-, Cr-, Ni- and Ti-content

    by Marina Gontijo, Christian Hoflehner, Sergiu Ilie, Jakob Six, Christof Sommitsch


  • Open Access

    Holding Time Influence on the Hot Ductility Behavior of a Continuously Cast Low Alloy Steel

    by Marina Gontijo, Christian Hoflehner, Sergiu Ilie, Jakob Six, Christof Sommitsch

    Cracking during the continuous casting process is undesirable and continuous work is being carried out to find further improvements and understand the mechanisms that lead to failure. Investigations on the hot ductility behavior of a continuously cast low alloyed steel using different holding times before straining were done in the present work. Samples were heated to melting temperature in a vacuum atmosphere and then cooled to one of the three test temperatures chosen: 750, 850, and 900 °C. When the desired temperature was reached, the sample was isothermally held for either 10, 90, 300, or 3600 s before the tensile test started, with a strain rate of 10−3 s−1. The reduction of area was measured, SEM images of the fractured surfaces were taken plus LOM images for the analysis of the microstructure. The results show that there was no significant change in the ductility at any of the temperatures until 300 s, with a change in behavior at 3600 s. This was further confirmed with the images and precipitation kinetics simulations. The results are described and compared.