Stanislovas Bartkevicius
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Stanislovas Bartkevicius has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
K. Sarkauskas
Kaunas Univ Technol, Dept Automat, Kaunas, Lithuania
3 shared publications- O. Fiodorova
Kaunas Univ Technol, Dept Automat, Panevezys, Lithuania
2 shared publications - Virginijus Baranauskas
Department of Automation, Faculty of Electrical and Electronics Engineering, Kaunas University of Technology, Studentu St. 48-320, LT-51367 Kaunas, Lithuania
2 shared publications - Alma Derviniene
Department of Electronics Engineering, Faculty of Electrical and Electronics Engineering, Kaunas University of Technology, Studentu St. 48-213, LT-51367 Kaunas, Lithuania
1 shared publication - Andrius Knyš
Department of Electrical and Energy Systems, Kaunas University of Technology, Studentu Str. 48, LT-51367 Kaunas, Lithuania
1 shared publication - Arunas Lipnickas
Department of Automation, Kaunas University of Technology, 51367 Kaunas, Lithuania
1 shared publication
Latest Publications
- 1 June 2018
- Published by Tech Science Press in Intelligent Automation and Soft Computing
- Vol. 24 (2) , 241-248
Mobile Robots Navigation Modeling in Known 2d Environment Based on Petri Nets
- 1 June 2018
- Published by Tech Science Press in Intelligent Automation and Soft Computing
- Vol. 24 (2) , 241-248
Mobile Robots Navigation Modeling in Known 2d Environment Based on Petri Nets
- 11 September 2013
- Published by Kaunas University of Technology (KTU) in Elektronika ir Elektrotechnika
- Vol. 19 (7) , 7-10
Detecting the Mobile Robot Position Using the Profile of Known Environment
The present wayward robot on the task tracks the coordinate search, using only scanners, located inside robot. In order to determine robot coordinates, the virtual scanner and scanner obtained profiles are used. The profile mismatch formed optimization criteria, the surface of which has a lot of local minimum, a number of which depends on the scanning step. Selected scanning angle step size, and determined what should be the optimization strategy, that the searched result converged. The obtained results allow carrying out further research, given the setup process dynamics, the robot moves and coordinate accuracy is a critical problem solution in determining the coordinates, time.DOI: http://dx.doi.org/10.5755/j01.eee.19.7.5156
- 11 September 2013
- Published by Kaunas University of Technology (KTU) in Elektronika ir Elektrotechnika
- Vol. 19 (7) , 7-10
Detecting the Mobile Robot Position Using the Profile of Known Environment
The present wayward robot on the task tracks the coordinate search, using only scanners, located inside robot. In order to determine robot coordinates, the virtual scanner and scanner obtained profiles are used. The profile mismatch formed optimization criteria, the surface of which has a lot of local minimum, a number of which depends on the scanning step. Selected scanning angle step size, and determined what should be the optimization strategy, that the searched result converged. The obtained results allow carrying out further research, given the setup process dynamics, the robot moves and coordinate accuracy is a critical problem solution in determining the coordinates, time.DOI: http://dx.doi.org/10.5755/j01.eee.19.7.5156
- Open Access
- 9 May 2012
- Published by Kaunas University of Technology (KTU) in Elektronika ir Elektrotechnika
- Vol. 121 (5) , 75-78
Vector Approach of Collision Prognosis of Mobile Robots
A method to detect potential collision of moving robots, operating in the same environment, is discussed. Criteria of collision is formulated – two robots will collide, if the angle between vector of difference of speeds and difference of vectorial distances of robots to crossing point of linear traces is less then half of the visibility angle, from position of one of robots, of the circle with diameter equal to sum of diameters of circles involving robots, placed in position of other robot. It is determined, that usage of this criteria allows to check possible collisions only in start position of robots or when one of them changes direction of movement. Ill. 4, bibl. 4 (in English; abstracts in English and Lithuanian).DOI: http://dx.doi.org/10.5755/j01.eee.121.5.1655
- 9 May 2012
- Published by Kaunas University of Technology (KTU) in Elektronika ir Elektrotechnika
- Vol. 121 (5) , 75-78
Open AccessVector Approach of Collision Prognosis of Mobile Robots
A method to detect potential collision of moving robots, operating in the same environment, is discussed. Criteria of collision is formulated – two robots will collide, if the angle between vector of difference of speeds and difference of vectorial distances of robots to crossing point of linear traces is less then half of the visibility angle, from position of one of robots, of the circle with diameter equal to sum of diameters of circles involving robots, placed in position of other robot. It is determined, that usage of this criteria allows to check possible collisions only in start position of robots or when one of them changes direction of movement. Ill. 4, bibl. 4 (in English; abstracts in English and Lithuanian).DOI: http://dx.doi.org/10.5755/j01.eee.121.5.1655
- 1 September 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 325-330
Tool for Simulation of Control Systems
New tool for simulation of control systems (linear, non-linear and stochastic) is proposed. This software is written to simulate hybrid systems containing continuous and discrete (algorithmic) parts. Continuous processes are simulated using traditional structural schemes representing differential equations. Discrete links are simulated by a Petri net, which is connected with continuous part of a system model through special, new introduced, modified transitions - "processes". The net may control processes - switch them on or off. The continuous part sends real type values, which are used in guard expressions of "processes ", into the net.
- 1 September 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 325-330
Tool for Simulation of Control Systems
New tool for simulation of control systems (linear, non-linear and stochastic) is proposed. This software is written to simulate hybrid systems containing continuous and discrete (algorithmic) parts. Continuous processes are simulated using traditional structural schemes representing differential equations. Discrete links are simulated by a Petri net, which is connected with continuous part of a system model through special, new introduced, modified transitions - "processes". The net may control processes - switch them on or off. The continuous part sends real type values, which are used in guard expressions of "processes ", into the net.