BMBrian Anthony Mazzeo

Brian Anthony Mazzeo

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Brian Anthony Mazzeo has a total of 70 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    High-Yield Synthesis of Battery-Grade Silicon from Halloysite Through HF-Free Metallothermic Reduction

    by Kyle Charles Manwaring, Jaeseok Kim, Lizbeth Zurita-Garcia, Brian Anthony Mazzeo, Dean Richard Wheeler

    Magnesiothermic reduction is a promising route for synthesizing nanostructured silicon for battery anodes, yet commercial scalability is hindered by highly exothermic reaction conditions and reliance on hydrofluoric acid (HF) for purification. Here, it is demonstrated that intrinsic thermal accumulation during bulk synthesis drives the formation of magnesium silicate. To counteract this effect, a binary calcium chloride–magnesium chloride salt mixture was used as an intrinsic heat sink. By tuning its liquidus temperature to 675 °C, the reaction exotherm was absorbed via latent heat of fusion, preventing byproduct formation without microreactor geometries. Furthermore, an optimized ethanol-based purification protocol was developed to suppress surface silicon oxidation. This suppression circumvented the need for HF etching to remove unreacted surface oxides, resulting in a final silicon yield of approximately 93%. Additionally, powder X-ray diffraction is established as a predictive, high-throughput screening tool; the intensity of the amorphous scattering peak reliably correlates with surface oxide thickness and subsequent electrochemical failure. Ultimately, the fully optimized, HF-free silicon demonstrated sustained cyclability and capacity retention comparable to traditional HF-etched baselines. By resolving thermal scaling limits and surface oxide formation, this work establishes a high-yield and HF-free pathway for the commercial manufacturing of silicon anode active material.

  • Open Access

    Smart Bluetooth Stakes: Deployment of Soil Moisture Sensors with Rotating High-Gain Antenna Receiver on Center Pivot Irrigation Boom in a Commercial Wheat Field

    by Samuel Craven, Austin Bee, Blake Sanders, Eliza Hammari, Cooper Bond, Ruth Kerry, Neil Hansen, Brian A. Mazzeo

    Realization of the goals of precision agriculture is dependent on prescribing irrigation strategies matched to spatiotemporal variations in soil moisture on commercial farms. However, the scale at which these variations occur is not well understood. A high-spatial-density network of sensors with the ability to measure and report data over the course of a growing season is needed. In this work, design of the low-profile Smart Bluetooth Stake spatiotemporal soil moisture mapping system is presented. Smart stakes use Bluetooth Low Energy to communicate 64 MHz soil moisture impedance measurements from ground level to a receiver mounted on the center-pivot irrigation boom and equipped with a rotating high-gain parabolic antenna. Smart stakes can remain in the ground throughout the entire growing season without disrupting farm operations. A system of 86 sensors was deployed on a 50-hectare commercial field near Elberta, Utah, during the final growth stage of a crop of winter wheat. Different receiver antenna configurations were tested over the course of several weeks which included two full irrigation cycles. In the high-gain antenna configuration, data was successfully collected from 75 sensors, with successful packet transmission at ranges of approximately 600 m. Enough data was collected to construct a spatiotemporal moisture map of the field over the course of an irrigation cycle. Smart Bluetooth Stakes constitute an important advance in the spatial density achievable with direct sensors for precision agriculture.


  • Use of Vertical Electrical Impedance Measurements for Estimating Vertical Crack Depth in Reinforced Concrete

    by Enoch Boekweg, W. Spencer Guthrie, Brian A. Mazzeo

    Nondestructive testing using advanced tools is critical for assessing the condition of civil infrastructure. For concrete bridge decks, vertical electrical impedance (VEI) testing is a nondestructive testing technique that quantifies the quality of protection against chloride ion ingress provided to steel reinforcement. This work advances the use of VEI testing by offering an analytical, invertible model based on a cylindrical dipole approximation for interpreting VEI measurements of cracked concrete bridge decks. The model specifically predicts vertical crack depth from VEI measurements. The model is validated with numerical simulations and laboratory and field experiments.

  • Scanning mmWave Radar for Inspection of Thin Li-Ion Battery Electrode Films

    by Brian A. Mazzeo

    The electrical properties of thin, conductive films are important for the overall performance of many engineered systems but are especially important for Li-ion battery electrodes. Electrical measurements of electrodes are challenging because the thin, conductive films are attached to conductive metal substrates. Estimating film electrical heterogeneity typically has been performed either by destructive or contact methods. In this work, 60 GHz mmWave imaging radar is used to spatially map the radar-reflection properties of films in a non-contact measurement. Theoretical radar returns for battery electrode films are reviewed and a sensitivity analysis to conductivity and thickness changes is performed. A scanning system was constructed to move a radar module and radar-absorbing conduit across a battery film. Radar returns were recorded and mapped, demonstrating how this method could be used to study evolution of film properties during manufacturing processes and for Li-ion battery film quality control. A paint analog and PVDF-based carbon black film were used to demonstrate significant radar return changes during drying processes. Scanning of a commercial-quality Li-ion battery electrode film is reported. Film irregularities and blemishes impact the quality of scanned reflection data from the electrode film. Scanning mmWave radar could be an inexpensive method to interrogate properties of thin films in manufacturing processes.

  • Open Access

    Dual-Sensing Piezoresponsive Foam for Dynamic and Static Loading

    by Ryan A. Hanson, Cory N. Newton, Aaron Jake Merrell, Anton E. Bowden, Matthew K. Seeley, Ulrike H. Mitchell, Brian A. Mazzeo, David T. Fullwood

    Polymeric foams, embedded with nano-scale conductive particles, have previously been shown to display quasi-piezoelectric (QPE) properties; i.e., they produce a voltage in response to rapid deformation. This behavior has been utilized to sense impact and vibration in foam components, such as in sports padding and vibration-isolating pads. However, a detailed characterization of the sensing behavior has not been undertaken. Furthermore, the potential for sensing quasi-static deformation in the same material has not been explored. This paper provides new insights into these self-sensing foams by characterizing voltage response vs frequency of deformation. The correlation between temperature and voltage response is also quantified. Furthermore, a new sensing functionality is observed, in the form of a piezoresistive response to quasi-static deformation. The piezoresistive characteristics are quantified for both in-plane and through-thickness resistance configurations. The new functionality greatly enhances the potential applications for the foam, for example, as insoles that can characterize ground reaction force and pressure during dynamic and/or quasi-static circumstances, or as seat cushioning that can sense pressure and impact.


  • Direct Measurements of Ionic Transport Behavior of Dual-Layer Porous Electrodes

    by Baichuan Liu, Nicole James, Amir-Sina Hamedi, Adrian Yao, Stephen Trask, Brian Mazzeo, Dean R. Wheeler

    To improve power and cycling performance of lithium-ion batteries, dual-layer or porosity-gradient electrodes have been proposed. By engineering a higher porosity close to the separator, the intention is to improve ion transport where it is most impactful. In this research, MacMullin numbers of two dual-layer anode samples are tested using an impedance measurement technique developed previously. To characterize the microstructure of each layer independently, we developed an improved transmission-line model that accounts for each layer’s properties.Virtual experiments using COMSOL Multiphysics to simulate impedance measurements are used to examine and improve the accuracy of the numerical inversion procedure. The results for the two dual-layer anodes studied show that MacMullin numbers follow expected trends, though the anodes are quite different from each other.

  • Open Access

    Li-ion Electrode Microstructure Evolution during Drying and Calendering

    by Mojdeh Nikpour, Baichuan Liu, Paul Minson, Zachary Hillman, Brian A. Mazzeo, Dean R. Wheeler

    The drying process of electrodes might seem to be a simple operation, but it has profound effects on the microstructure. Some unexpected changes can happen depending on the drying conditions. In prior work, we developed the multiphase-smoothed-particle (MPSP) model, which predicted a relative increase in the carbon additive and binder adjacent to the current collector during drying. This motivated us to undertake the present experimental investigation of the relationship between the drying rate and microstructure and transport properties for a typical anode and cathode. Specifically, the drying rate was controlled by means of temperature for both an NMC532 cathode and graphite anode. The material distribution was analyzed using a combination of cross-section SEM images and the energy-dispersive X-ray spectroscopy elemental maps. The binder concentration gradients were developed in both the in- and through-plane directions. The through-plane gradient is evident at a temperature higher than 150 °C, whereas the in-plane variations resulted at all drying temperatures. The measurements identified an optimum temperature (80 °C) that results in high electronic conductivity and low ionic resistivity due to a more uniform binder distribution. Trends in transport properties are not significantly altered by calendering, which highlights the importance of the drying rate itself on the assembled cell properties.


  • Li-Ion Battery Electrode Contact Resistance Estimation by Mechanical Peel Test

    by John E. Vogel, Jarom G. Sederholm, Edmund M. Shumway, Gabriel J. Abello, Stephen E. Trask, Dean R. Wheeler, Brian A. Mazzeo

    Li-ion battery electrode electronic properties, including bulk conductivity and contact resistance, are critical parameters affecting cell performance and fast-charge capability. Contact resistance between the coating and current collector is often the largest electronic resistance in an electrode and is affected by chemical, microstructural, and interfacial variations. Direct measurements of contact resistance and bulk conductivity have proven to be challenging. In their absence, a mechanical electrode peel test is often used to compare adhesion and electrical contact resistance. However, using a micro-flexible-surface probe, contact resistance can be directly determined. This work compares contact resistance and mechanical peel strength of multiple commercial-grade HE5050 and NCM523 cathodes and graphite and silicon anodes. It was found that peel strength correlates well with contact resistance in a carefully curated data set (p < 0.05) and in some situations may be a good metric to estimate electrical properties. However, there were distinct outliers in the data set, indicating that peel strength may not accurately reflect electrical properties when there is significant variation in electrode composition. These results illustrate the value of the micro-flexible-surface probe in quantifying contact resistance and bulk conductivity to better understand how battery composition and processing steps affect microstructure and resulting cell performance.


  • Open Access

    A Generalized Method for In-Process Defect Detection in Friction Stir Welding

    by Johnathon B. Hunt, Brian A. Mazzeo, Carl D. Sorensen, Yuri Hovanski

    Friction stir welding (FSW) is an advantageous solid-state joining process that is suitable for many materials in multiple industries. In an industrial setting, manufacturers are actively seeking faster welding speeds to increase throughput. Increasing welding speed limits the size of defect-free parameter windows, which may increase the frequency of defects. The push for faster welding speeds emphasizes the need for economical non-destructive evaluation (NDE) for FSW, like any other type of welding. This work introduces a generalized defect detection method that recognizes the stochastic nature of the FSW process, and that can be generally applied to FSW of a material across a dynamic range of process parameters and welding conditions. When applied to aluminum friction stir-welded blanks at speeds ranging from 1500 to 3000 mm/min with varying ranges of tool tilts, the methodology proved 100% effective at positive detection when defects were present with zero scrap rate. Furthermore, additional development demonstrated the proposed stochastic approach can be used to detect the spatial location of a defect within a weld with 94% detection accuracy and a 4.2% scrap rate.


  • Heterogeneity in MacMullin Number of Li-Ion Battery Electrodes Studied by Means of an Aperture Probe

    by Baichuan Liu, Kayci Prugue, Mojdeh Nikpour, Kristopher Ward, Brian A. Mazzeo, Dean R. Wheeler

    Heterogeneity of MacMullin number within battery electrodes is a key metric affecting cell performance. To characterize this heterogeneity, an aperture probe was developed. This probe, coupled with a newly developed transmission-line model, allows for measurements of tortuosity, represented by the MacMullin number, on millimeter length scales. Local MacMullin number values of seven electrodes were measured, and the ionic resistance profiles of these electrodes are given through contour maps of the MacMullin number. The method is validated by comparing the average MacMullin number to the value obtained through other measurement methods. The results show significant local MacMullin number variation in such electrodes on a millimeter length scale. This method will allow battery manufacturers and researchers to better quantify sources of heterogeneity and improve electrode quality.