MHMatthew H. Hebdon

Matthew H. Hebdon

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Matthew H. Hebdon has a total of 57 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Modeling Techniques for Evaluating the Redundancy of Composite Steel Tub Girder Bridges Subjected to Brittle Fracture

    by Mojtaba Aliasghar-Mamaghani, Loveleen Loveleen, Xiaoyi Chen, Aidan Bjelland, Matthew Hebdon, Todd A. Helwig, Sunghyun Park, Jeonghwa Lee, Michael D. Engelhardt

    Twin-girder bridges have historically been classified as nonredundant due to the perceived inability of the bridge to support the required vehicular loading if one of the girders were to fail. Although this classification is likely appropriate for twin I-girder bridges, twin-tub girder bridges have been shown to possess significant redundancy even with the failure of a girder. Advances from previous studies have induced the Federal Highway Administration to permit redundancy to be demonstrated through analysis in the failed state. The analysis requires a simulated fracture in a girder with applied loading consisting of the bridge self-weight and live load. Bridge models in the failed state require a relatively fine mesh and complex loading application, demanding significant computational resources and analysis run times that can require weeks to complete even on a powerful computer system. This paper outlines the development and validation of computational modeling methods for evaluating the redundancy of twin-tub girder bridges subjected to brittle fracture. The computational framework employs implicit and explicit algorithms to capture the respective cases of the construction sequence, fracturing of a girder, and application of vehicular live loads. While an implicit algorithm is advantageous for evaluating behavior during the construction phase, the adoption of an explicit algorithm is indispensable for analyses involving fracture, since implicit algorithms are not well-tailored for cases with severe material and geometric nonlinearities. Ensuring accuracy in both modeling and analysis techniques requires validation, which was completed using full-scale experimental results from a twin-tub girder bridge fracture test. Redundancy analyses are demonstrated on three existing bridges that include both straight and curved geometries. Modeling efficiency is improved and demonstrated by varying multiple parameters. In particular, results elucidate the efficacy of mass scaling and damping in reducing the computational effort. The techniques and recommendations dramatically improve the efficiency of the analyses.

  • Quantitative description of chloride ingress in concrete using machine learning algorithms

    by Mojtaba Aliasghar-Mamaghani, Ioannis Koutromanos, Matthew Hebdon, Carin Roberts-Wollmann


  • Development of Extendable Open-Source Structural Inspection Datasets

    by Eric Bianchi, Matthew Hebdon

    Recent infrastructure inspection has used deep-learning models to enhance and augment typical inspection tasks such as detecting and quantifying damage. One of the issues with this trend is that deep-learning models typically require a significant amount of data. In a data domain such as structural inspection, publicly accessible data are difficult to find, making the advancement of this research slower. Therefore, we set out to acquire bridge inspection data by selectively extracting candidate images from hundreds of thousands of bridge inspection reports from the Virginia Department of Transportation. Using this rich source of diverse data, we refined our collected data to develop four high-quality, easily extendable, publicly accessible datasets, tested with state-of-the-art models to support typical bridge inspection tasks. The four datasets: labeled cracks in the wild, 3,817 image sets of semantically segmented concrete cracks taken from diverse scenery; 3,817 image sets of semantically segmented structural inspection materials (concrete, steel, metal decking); 440 images of finely annotated steel corrosion condition state (good, fair, poor, severe); and 1,470 images of fatigue-prone structural steel bridge details (bearings, gusset plates, cover plate terminations, and out-of-plane stiffeners) for object detection. To ensure the extendibility of the datasets, the authors have proposed annotation guidelines to maintain consistent growth through annotation collaboration. Researchers can use these trained models and data for auxiliary inspection tasks such as damage detection, damage forecasting, automatic report generation, and, coupled with the assistance of unmanned aerial systems, for autonomous flight path planning and object avoidance. The procedures, concepts, and repositories provided in this paper will help to set a course for the advancement of better detection models using high-quality accessible and extendable datasets. Researchers can use these datasets and trained models for auxiliary inspection tasks such as damage detection, damage forecasting, automatic report generation, and, coupled with the assistance of unmanned aerial systems, for autonomous flight path planning and object avoidance. The models may also be used as starting points for researchers to extend or begin their own use-case datasets for this domain or similar domain of data. The authors have presented three main reasons for including annotations guidelines for any public dataset: to establish consistent annotations for the training and testing data; to clearly present the expected model prediction; for guiding future collaborators. Annotation guidelines are a practical tool for any researcher procuring a dataset for supervised machine learning.


  • Analytical Evaluation of Corrosion-Induced Strength Degradation in Prestressed Bridge Girders

    by Mojtaba Aliasghar-Mamaghani, Ioannis Koutromanos, Carin Roberts-Wollmann, Matthew Hebdon

    This paper uses nonlinear analysis to determine the impact of corrosion-induced damage on the load-carrying capacity of prestressed concrete bridge girders. The analyses rely on two types of models, namely, beam models and nonlinear truss models. The latter are deemed necessary to obtain reliable estimates of the shear capacity, as beam models are not well-tailored for capturing shear failures. A procedure to account for the reduction in area and deformability of corroded strands, based on visually observed corrosion damage, is proposed and implemented. The models are calibrated and validated with the results of experimental tests on prestressed girders, which exhibited varying levels of corrosion-induced damage. Further analyses allow the comparison of the capacity of corrosion-damaged girders to that of their undamaged counterparts. The accuracy of a simplified procedure, using equations in the AASHTO code to determine the flexural and shear capacity of the damaged girders, is also determined.


  • Experimental and Analytical Investigation of a 64-Year-Old Prestressed Beam Retrofitted with External Posttensioning

    by Lena Leicht, Carin L. Roberts-Wollmann, Ioannis Koutromanos, Matthew H. Hebdon, Oliver Mosig

    This paper presents an experimental investigation of a 64-year-old, full-scale, simply supported, prestressed bridge girder retrofitted with external posttensioning. The specific retrofit can be used to increase the flexural strength of corrosion-damaged prestressed beams. The test specimen, taken from a bridge located in Virginia, was subjected to monotonically increasing loads until the occurrence of a diagonal compression failure in the vicinity of one of the external tendon anchor blocks. The experimental test was accompanied by finite-element analyses, aimed to elucidate the failure mode and quantify the impact of the repair on the capacity of damaged beams. Simplified calculations based on strut-and-tie models and design code guidelines are found to give satisfactory estimates of the failure load, while also describing the principal aspects of the force transfer between the external tendons and the beam and the stress state in the immediate vicinity of the anchor blocks.


  • Tightening Procedures for Proper Installation of Anchor Rods in Ancillary Structures

    by Japsimran Singh, Matthew H. Hebdon

    In the last 2 decades, many ancillary structures have collapsed, with several instances traceable to loose anchor nuts. According to a quality assurance inspection conducted by the Virginia Department of Transportation (VDOT) in 2012, approximately 30% of the anchor nuts on the inspected ancillary structures across the state of Virginia were found to be loose. The exact cause of the loose anchor nuts is not known; however, one theory is that specified tightening procedures were not properly followed or were not adequate. Currently, a turn-of-the-nut method is used for the tightening of anchor nuts on double-nut moment connections at the base of ancillary structures. This research reviewed current tightening procedures for anchor nuts on ancillary structures. The relationship between three critical tightening parameters—applied torque, nut rotation, and pretension in the rod—was examined. One hundred galvanized steel anchor rods of five different diameters and three different grades were tested. The experimental tests serve as a benchmark to validate the current tightening procedures, as well as to recommend changes.

  • COCO-Bridge: Structural Detail Data Set for Bridge Inspections

    by Eric Bianchi, Amos Lynn Abbott, Pratap Tokekar, Matthew Hebdon

    The purpose of this research is to propose a means to address two issues faced by unmanned aerial vehicles (UAVs) during bridge inspection. The first issue is that UAVs have a notoriously difficult time operating near bridges. This is because of the potential for the navigation signal to be lost between the operator and the UAV. Therefore, there is a push to automate or semiautomate the UAV inspection process. One way to improve automation is by improving UAVs’ ability to contextualize their environment through object detection and object avoidance. The second issue is that, to the best of the authors’ knowledge, no method has been developed to automatically contextualize detected defects to a structural bridge detail during or after UAV flight. Significant research has been conducted on UAVs’ ability to detect defects, like cracks and corrosion. However, detecting the presence of a defect alone does not contextualize its significance or help with an inspector’s job to rate specific structural bridge details. This paper outlines a use case for a data set and model to detect critical structural bridge details, providing context and vision for enhancing the autonomous UAV bridge inspection process. Identifying these structural bridge details that require inspection may assist an UAV in path planning and object avoidance in GPS-denied environments. The detection of structural details adds an ability to contextualize defect detection and localize issues to a bridge detail. This also has implications for providing cues to inspectors, in real time, on defect-susceptible areas while UAVs are in flight. The image data set, Common Objects in Context for bridge inspection (COCO-Bridge), for UAV object detection was collected and then trained using deep learning techniques. This data set consists of 774 images and over 2,500 object instances to detect 4 structural bridge details: bearings, cover plate terminations, gusset plate connections, and out-of-plane stiffeners. These details were chosen because they either must be rated by an inspector or checked because they are prone to failure. Methods to economize the predictive capabilities of the model through image augmentation were investigated to extend the performance of the training images. It was concluded that for this domain of data, structural bridge detail images, the mean average precision, and F1 score performance were improved by mirroring the training images along their y -axis. The outcome of this paper was an open-source annotated data set, which can be used in computer vision applications for visual inspection, growing the capabilities of artificial intelligence in structural engineering.


  • Investigation of Anchor Nut Loosening on Highway Ancillary Structures

    by Japsimran Singh, Matthew H. Hebdon

    Documented evidence shows that anchor nut loosening on highway ancillary structures has been a problem in the transportation industry since at least the 1990s. There have been reported cases in the past, where loose anchor nuts were found to be partially responsible for the failure of ancillary structures. Resonant vibrations in ancillary structures as a result of variable frequency winds are believed to be one of the potential causes of loose anchor nuts. The current research primarily focused on investigating the effect of wind-induced vibrations on the loosening of anchor nuts in double-nut moment connections in ancillary structures. The research involved large-scale vibration testing of a traffic signal on the basis of vibration stress results from a 4-month field monitoring program. The purpose of the large-scale testing was to establish the relationship between the number of vibratory cycles, rod pretension, and nut loosening. A small-scale vibration test was also performed to validate the large-scale testing results. The testing results showed that anchor rods tightened in a double-nut moment connection above a pretension of 38 MPa (5.5 Ksi) do not experience nut loosening under vibrations.


  • Correlating Surface Hardness to Shear Strength of Driven Rivets and Distribution of In Situ Rivet Hardness

    by Ryan T. Stevens, Ryan J. Sherman, Matthew H. Hebdon

    Measuring surface hardness and correlating it to shear strength is a nondestructive test method that can be used when a more accurate estimate of rivet strength is necessary. The objectives of this research were to (1) correlate the surface hardness to shear strength of driven rivets, and (2) determine if a subset of rivets could be tested to estimate the hardness of all rivets on a structure. Modern rivets were driven with a pneumatic rivet hammer and tested with a portable hardness tester. The shear strength was then estimated using the approximate tensile strength and two factors, 0.58 and 0.85, from previous research. When using the 0.85 factor, the difference between estimated and actual shear strengths was as low as 1%–6%, compared with 28%–34% when using the 0.58 factor. A factor of 4.8 MPa/hardness Rockwell B (HRB) (0.7  ksi/HRB ) was then proposed as a direct correlation between surface hardness and shear strength. The range of rivet hardness measurements was approximately 30 HRB for each of the three bridges tested. Thus, it would be inappropriate to estimate the hardness of all rivets from a small subset of tested rivets. A proposed method is to test a subset of rivets on a member or connection of interest and use those measurements to estimate the hardness of rivets only on that member or connection.