Dongyun Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dongyun Zhang has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
Dongdong Dong
Institute of New Materials, Guangdong Academy of Sciences, National Engineering Laboratory of Modern Materials Surface Engineering Technology, Guangdong Provincial Key Laboratory of Modern Surface Engineering Technology, Guangzhou, China
2 shared publicationsSongtao Hu
Institute of Laser Engineering, Faculty of Materials and Manufacturing, Beijing University of Technology, Beijing, China
2 shared publications- Yangli Xu
Institute for Laser Engineering, Beijing University of Technology, Pingleyuan No.100, Chaoyang Dist., Beijing, 100124, China
2 shared publications ChengJie Wang
Beijing University of Technology
1 shared publicationDongDong Dong
Beijing University of Technology
1 shared publicationHao Huang
Institute of Laser Engineering, Faculty of Materials and Manufacturing, Beijing University of Technology, Beijing, China
1 shared publication
Latest Publications
- 25 September 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 129 (1-2) , 969-982
Influence of the properties of Ti6Al4V powder materials on the build quality of laser powder bed fusion–manufactured components
- 25 September 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 129 (1-2) , 969-982
Influence of the properties of Ti6Al4V powder materials on the build quality of laser powder bed fusion–manufactured components
- Open Access
Numerical Simulation in the Melt Pool Evolution of Laser Powder Bed Fusion Process for Ti6Al4V
In order to track the free interface of the melt pool and understand the evolution of the melt pool, the flow of fluid, and the interface behavior of gas and liquid, a physical model is developed by using the VOF method in this paper. Its characteristics are a combined heat source model, including a parabolic rotation and a cylindrical distribution, and a powder bed stochastic distributed model with powder particle size. The unit interface between the metallic and gas phase in the laser–powder interaction zone can only be loaded by the heat source. Only the first and second laser scanning tracks are simulated to reduce the calculation time. The simulation results show that process parameters such as laser power and scanning speed have significant effects on the fluid flow and surface morphology in the melt pool, which are in good agreement with the experimental results. Compared with the first track, the second track has larger melt pool geometry, higher melt temperature, and faster fluid flow. The melt flows intensely at the initial position due to the high flow rate in the limited melt space. Because there is enough space for the metal flow, the second track can obtain smooth surface morphology more easily compared to the first track. The melt pool temperature at the laser beam center fluctuates during the laser scanning process. This depends on the effects of the interaction between heat conduction or heat accumulation or the interaction between heat accumulation and violent fluid flow. The temperature distribution and fluid flow in the melt pool benefit the analysis and understanding of the evolution mechanism of the melt pool geometry and surface topography and further allow regulation of the L-PBF process of Ti6Al4V.
Open AccessNumerical Simulation in the Melt Pool Evolution of Laser Powder Bed Fusion Process for Ti6Al4V
In order to track the free interface of the melt pool and understand the evolution of the melt pool, the flow of fluid, and the interface behavior of gas and liquid, a physical model is developed by using the VOF method in this paper. Its characteristics are a combined heat source model, including a parabolic rotation and a cylindrical distribution, and a powder bed stochastic distributed model with powder particle size. The unit interface between the metallic and gas phase in the laser–powder interaction zone can only be loaded by the heat source. Only the first and second laser scanning tracks are simulated to reduce the calculation time. The simulation results show that process parameters such as laser power and scanning speed have significant effects on the fluid flow and surface morphology in the melt pool, which are in good agreement with the experimental results. Compared with the first track, the second track has larger melt pool geometry, higher melt temperature, and faster fluid flow. The melt flows intensely at the initial position due to the high flow rate in the limited melt space. Because there is enough space for the metal flow, the second track can obtain smooth surface morphology more easily compared to the first track. The melt pool temperature at the laser beam center fluctuates during the laser scanning process. This depends on the effects of the interaction between heat conduction or heat accumulation or the interaction between heat accumulation and violent fluid flow. The temperature distribution and fluid flow in the melt pool benefit the analysis and understanding of the evolution mechanism of the melt pool geometry and surface topography and further allow regulation of the L-PBF process of Ti6Al4V.
- 1 November 2019
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 99, 225-239
Mechanical properties tailoring of topology optimized and selective laser melting fabricated Ti6Al4V lattice structure
- 1 November 2019
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 99, 225-239
Mechanical properties tailoring of topology optimized and selective laser melting fabricated Ti6Al4V lattice structure
- 12 November 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10813, 1081310
Numerical simulation in the laser energy absorption behavior of Ti6Al4V powder materials during SLM
In the paper, the effects of porosities and average particle sizes of powder layer on light absorption during SLM process were investigated, in which closed-packing models based on Horsfieled’s filling method were established and light absorption was simulated using ray tracing based on laser-material interaction mechanism. The results show the absorption of powder layer of Ti6Al4V alloy is higher than 70%. The decrease of porosity of powder layer benefits to improve the absorption, while the absorption tends to decrease if porosity decreases to a certain value due to the reflection. The decrease of average particle size of powder particles benefits also to improve the absorption. If the light irradiates at positions with different particle arrangements, the absorption behavior changes with irradiation condition whether there occurs the multi-reflection. The above research provides theoretical basis for preparation of new powder materials, their parameter developing for SLM technology and even the properties regulation of SLM fabricated component.
- 12 November 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10813, 1081310
Numerical simulation in the laser energy absorption behavior of Ti6Al4V powder materials during SLM
In the paper, the effects of porosities and average particle sizes of powder layer on light absorption during SLM process were investigated, in which closed-packing models based on Horsfieled’s filling method were established and light absorption was simulated using ray tracing based on laser-material interaction mechanism. The results show the absorption of powder layer of Ti6Al4V alloy is higher than 70%. The decrease of porosity of powder layer benefits to improve the absorption, while the absorption tends to decrease if porosity decreases to a certain value due to the reflection. The decrease of average particle size of powder particles benefits also to improve the absorption. If the light irradiates at positions with different particle arrangements, the absorption behavior changes with irradiation condition whether there occurs the multi-reflection. The above research provides theoretical basis for preparation of new powder materials, their parameter developing for SLM technology and even the properties regulation of SLM fabricated component.
- Open Access
Study on Topology Optimization Design, Manufacturability, and Performance Evaluation of Ti-6Al-4V Porous Structures Fabricated by Selective Laser Melting (SLM)
The combination of topology optimization (TOP) and selective laser melting (SLM) provides the possibility of fabricating the complex, lightweight and high performance geometries overcoming the traditional manufacturing “bottleneck”. This paper evaluates the biomechanical properties of porous structures with porosity from 40% to 80% and unit cell size from 2 to 8 mm, which are designed by TOP and manufactured by SLM. During manufacturability exploration, three typical structures including spiral structure, arched bridge structure and structures with thin walls and small holes are abstracted and investigated, analyzing their manufacturing limits and forming reason. The property tests show that dynamic elastic modulus and compressive strength of porous structures decreases with increases of porosity (constant unit cell size) or unit cell size (constant porosity). Based on the Gibson-Ashby model, three failure models are proposed to describe their compressive behavior, and the structural parameter λ is used to evaluate the stability of the porous structure. Finally, a numerical model for the correlation between porous structural parameters (unit cell size and porosity) and elastic modulus is established, which provides a theoretical reference for matching the elastic modulus of human bones from different age, gender and skeletal sites during innovative medical implant design and manufacturing.
Open AccessStudy on Topology Optimization Design, Manufacturability, and Performance Evaluation of Ti-6Al-4V Porous Structures Fabricated by Selective Laser Melting (SLM)
The combination of topology optimization (TOP) and selective laser melting (SLM) provides the possibility of fabricating the complex, lightweight and high performance geometries overcoming the traditional manufacturing “bottleneck”. This paper evaluates the biomechanical properties of porous structures with porosity from 40% to 80% and unit cell size from 2 to 8 mm, which are designed by TOP and manufactured by SLM. During manufacturability exploration, three typical structures including spiral structure, arched bridge structure and structures with thin walls and small holes are abstracted and investigated, analyzing their manufacturing limits and forming reason. The property tests show that dynamic elastic modulus and compressive strength of porous structures decreases with increases of porosity (constant unit cell size) or unit cell size (constant porosity). Based on the Gibson-Ashby model, three failure models are proposed to describe their compressive behavior, and the structural parameter λ is used to evaluate the stability of the porous structure. Finally, a numerical model for the correlation between porous structural parameters (unit cell size and porosity) and elastic modulus is established, which provides a theoretical reference for matching the elastic modulus of human bones from different age, gender and skeletal sites during innovative medical implant design and manufacturing.
- 7 April 2017
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 26 (5) , 831-845
Modeling of Temperature Field Evolution During Multilayered Direct Laser Metal Deposition
- 7 April 2017
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 26 (5) , 831-845
Modeling of Temperature Field Evolution During Multilayered Direct Laser Metal Deposition