Livia Zumofen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Livia Zumofen has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Andreas Kirchheim
Centre for Product and Process Development ZPP, School of Engineering, Zurich University of Applied Sciences ZHAW, Winterthur, Switzerland
5 shared publicationsHans-Jörg Dennig
Centre for Product and Process Development, School of Engineering, Zurich University of Applied Sciences, Winterthur, Switzerland
3 shared publications- Andreas Kirchheim
Centre for Product and Process Development, Zurich University of Applied Sciences, Winterthur, Switzerland
2 shared publications - Hans-Jörg Dennig
Institute of Product Development and Production Technologies, ZHAW, Winterthur, Switzerland
2 shared publications - Adriaan Bernardus Spierings
Inspire AG
1 shared publication Christian Beck
Zurich University of Applied Sciences
1 shared publication
Latest Publications
- Open Access
- 1 February 2022
- Published by Frontiers Media SA in Frontiers in Mechanical Engineering
- Vol. 7
Properties of Additive-Manufactured Open Porous Titanium Structures for Patient-Specific Load-Bearing Implants
Additive manufacturing has been well established in many sectors, including the medical industry. For load-bearing bone implants, titanium and its alloys, such as Ti6Al4V, are widely used due to their high strength to weight ratio and osseointegrative properties. However, bone resorption and loosening of implants is related to the significantly higher stiffness of dense Ti6Al4V, leading to stress shielding. With the aging of population, there is an increasing need for orthopedic implants with a high success rate and a long implant life span. Besides that the treatment of non-healing segmental bone defects, where the self-repairing properties of bone tissue are not sufficient, is still a challenge. In both fields of application, patient-specific titanium implants combined with functionally graded porosity designed according to locally expected loads unlock new possibilities. Many studies underline the huge potential of the new design freedom to generate open porous structures and more personalized implants with enhanced mechanical properties that also integrate well with surrounding tissues. Integration of functionally graded open porosity into implants allows for the implant to more closely mimic the mechanical properties of human bone and its internal architecture. The results of this work represent the basis for developing complex porous titanium structures with various pore sizes and shapes to tailor structural mechanical properties and biological responses. Therefore, 3D porous structures with various pore sizes and shapes were designed and manufactured in Ti6Al4V using laser powder bed fusion (PBF-LB/M). Based on these structures, the correlation of pore size and shape with cell ingrowth, morphology, metabolic activity, and early markers for bone formation (ALP activity) was investigated in static cell cultures using the osteosarcoma cell line Saos-2. Mechanical properties, such as stiffness and compression strength, were investigated with compression testing. The present study concludes that cell morphology, metabolic activity, and ALP activity are widely independent of pore shape and size within the tested range of 400–700 µm pore size. Furthermore, the mechanical properties of the evaluated structures were in the range of cortical and trabecular bone. This opens the possibility to design mechanical properties with gradient porosity without decisively affecting biological responses.
- 1 February 2022
- Published by Frontiers Media SA in Frontiers in Mechanical Engineering
- Vol. 7
Open AccessProperties of Additive-Manufactured Open Porous Titanium Structures for Patient-Specific Load-Bearing Implants
Additive manufacturing has been well established in many sectors, including the medical industry. For load-bearing bone implants, titanium and its alloys, such as Ti6Al4V, are widely used due to their high strength to weight ratio and osseointegrative properties. However, bone resorption and loosening of implants is related to the significantly higher stiffness of dense Ti6Al4V, leading to stress shielding. With the aging of population, there is an increasing need for orthopedic implants with a high success rate and a long implant life span. Besides that the treatment of non-healing segmental bone defects, where the self-repairing properties of bone tissue are not sufficient, is still a challenge. In both fields of application, patient-specific titanium implants combined with functionally graded porosity designed according to locally expected loads unlock new possibilities. Many studies underline the huge potential of the new design freedom to generate open porous structures and more personalized implants with enhanced mechanical properties that also integrate well with surrounding tissues. Integration of functionally graded open porosity into implants allows for the implant to more closely mimic the mechanical properties of human bone and its internal architecture. The results of this work represent the basis for developing complex porous titanium structures with various pore sizes and shapes to tailor structural mechanical properties and biological responses. Therefore, 3D porous structures with various pore sizes and shapes were designed and manufactured in Ti6Al4V using laser powder bed fusion (PBF-LB/M). Based on these structures, the correlation of pore size and shape with cell ingrowth, morphology, metabolic activity, and early markers for bone formation (ALP activity) was investigated in static cell cultures using the osteosarcoma cell line Saos-2. Mechanical properties, such as stiffness and compression strength, were investigated with compression testing. The present study concludes that cell morphology, metabolic activity, and ALP activity are widely independent of pore shape and size within the tested range of 400–700 µm pore size. Furthermore, the mechanical properties of the evaluated structures were in the range of cortical and trabecular bone. This opens the possibility to design mechanical properties with gradient porosity without decisively affecting biological responses.
- Open Access
- 13 September 2021
- Published by Springer Nature in Forschung im Ingenieurwesen
- Vol. 86 (3) , 595-604
Increasing the safety against scuffing of additive manufactured gear wheels by internal cooling channels
The layer-by-layer principle of the additive manufacturing (AM) technology of Laser-Powder-Bed-Fusion (LPBF) creates new opportunities in the design and manufacturing of efficient gear components. For example, integrating a cooling system can increase the safety against scuffing or reduce the amount of required lubrication and thus the splashing losses. Quenched and tempered steels or case-hardened steels are commonly used in the fabrication of gear components. However, the availability of these alloys for LPBF processing is still limited. The development of suitable LPBF metal gears (with a Gear Research Centre (FZG) type A geometry) out of quenched and tempered 30CrNiMo8 steel with internal cooling channels shows the possibility of significantly increasing the safety factor against scuffing. This work includes the development of a suitable cooling strategy, material development, the setup of a suitable test infrastructure and the analysis of the LPBF gears tested for scuffing.
- 13 September 2021
- Published by Springer Nature in Forschung im Ingenieurwesen
- Vol. 86 (3) , 595-604
Open AccessIncreasing the safety against scuffing of additive manufactured gear wheels by internal cooling channels
The layer-by-layer principle of the additive manufacturing (AM) technology of Laser-Powder-Bed-Fusion (LPBF) creates new opportunities in the design and manufacturing of efficient gear components. For example, integrating a cooling system can increase the safety against scuffing or reduce the amount of required lubrication and thus the splashing losses. Quenched and tempered steels or case-hardened steels are commonly used in the fabrication of gear components. However, the availability of these alloys for LPBF processing is still limited. The development of suitable LPBF metal gears (with a Gear Research Centre (FZG) type A geometry) out of quenched and tempered 30CrNiMo8 steel with internal cooling channels shows the possibility of significantly increasing the safety factor against scuffing. This work includes the development of a suitable cooling strategy, material development, the setup of a suitable test infrastructure and the analysis of the LPBF gears tested for scuffing.
- 1 September 2020
- Published by Springer Nature
- p. 304-320
Feasibility Investigation of Gears Manufactured by Fused Filament Fabrication
- 1 September 2020
- Published by Springer Nature
- p. 304-320
Feasibility Investigation of Gears Manufactured by Fused Filament Fabrication
- Open Access
- 20 February 2020
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 5 (1) , 75-81
Laser powder bed fusion of 30CrNiMo8 steel for quenching and tempering: examination of the processability and mechanical properties
The layer-by-layer principle of additive manufacturing technology laser powder bed fusion (LPBF) opens up completely new possibilities in the design and manufacturing of lightweight and efficient gear components. For example, integration of contour conform cooling and lubrication channels into gear components can increase their service life and reduce lubricant consumption. Steels for quenching and tempering and case hardening steels are commonly used materials for gear components. However, the availability of these alloys for LPBF processing is still limited. In particular, the 30CrNiMo8 steel for quenching and tempering is frequently used for gear wheels. This specific alloy is largely unknown regarding LPBF processing and remains challenging, because of its susceptibility to cracking and the high temperature gradients that occur during the LPBF process. Therefore, this study focuses on the LPBF processing of 30CrNiMo8 powder material including process parameter evaluation and material characterization. Additionally, effects of the heat treatment on the resulting microstructure and mechanical properties were investigated. Within this study the 30CrNiMo8 has been processed successfully with a density of well above 99.5% leading to promising mechanical properties. A more homogenous microstructure has been achieved with quenching and tempering, compared to the as-build state.
- 20 February 2020
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 5 (1) , 75-81
Open AccessLaser powder bed fusion of 30CrNiMo8 steel for quenching and tempering: examination of the processability and mechanical properties
The layer-by-layer principle of additive manufacturing technology laser powder bed fusion (LPBF) opens up completely new possibilities in the design and manufacturing of lightweight and efficient gear components. For example, integration of contour conform cooling and lubrication channels into gear components can increase their service life and reduce lubricant consumption. Steels for quenching and tempering and case hardening steels are commonly used materials for gear components. However, the availability of these alloys for LPBF processing is still limited. In particular, the 30CrNiMo8 steel for quenching and tempering is frequently used for gear wheels. This specific alloy is largely unknown regarding LPBF processing and remains challenging, because of its susceptibility to cracking and the high temperature gradients that occur during the LPBF process. Therefore, this study focuses on the LPBF processing of 30CrNiMo8 powder material including process parameter evaluation and material characterization. Additionally, effects of the heat treatment on the resulting microstructure and mechanical properties were investigated. Within this study the 30CrNiMo8 has been processed successfully with a density of well above 99.5% leading to promising mechanical properties. A more homogenous microstructure has been achieved with quenching and tempering, compared to the as-build state.
- 6 September 2017
- Published by Springer Nature
- p. 210-219
Quality Related Effects of the Preheating Temperature on Laser Melted High Carbon Content Steels
- 6 September 2017
- Published by Springer Nature
- p. 210-219
Quality Related Effects of the Preheating Temperature on Laser Melted High Carbon Content Steels
- 6 September 2017
- Published by Springer Nature
- p. 329-336
Why Education and Training in the Field of Additive Manufacturing is a Necessity
- 6 September 2017
- Published by Springer Nature
- p. 329-336
Why Education and Training in the Field of Additive Manufacturing is a Necessity
- 20 March 2017
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 23 (2) , 362-369
Approaches to minimize overhang angles of SLM parts
Purpose: For geometries exhibiting overhanging surfaces, support structures are needed to dissipate process heat and to minimize geometrical distortions attributed to internal stresses. The use of support structures is often time- and cost-consuming. For this reason, this study aims to propose an approach which minimizes the use of such structures. Design/methodology/approach: For minimizing the use of support structures, process parameters in combination with a contour-like exposure strategy are developed to realize support-less overhanging structures of less than 35°. These parameters are implemented in a shell-core strategy, which follows the idea of applying different processing strategies to the critical (overhanging) shell and the uncritical core of the part. Thereby, the core is processed with standard parameters, aiming a dense material. On the critical shell, optimized processing parameters are applied, reaching good results in terms of surface quality, especially at extreme overhang situations. Findings: The results show that the selective laser melting (SLM) technology is able to realize support-less overhanging surfaces by choosing suitable scan strategies and process parameters. Particularly good results are always obtained when the exposure direction of the shell is parallel to the contour of the sample. Originality/value: The validity of the results is demonstrated through the successful reproduction of the build strategy on two commercial SLM machines, reaching support-free builds of surfaces with an angle to the horizontal of less than or equal to 30°.
- 20 March 2017
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 23 (2) , 362-369
Approaches to minimize overhang angles of SLM parts
Purpose: For geometries exhibiting overhanging surfaces, support structures are needed to dissipate process heat and to minimize geometrical distortions attributed to internal stresses. The use of support structures is often time- and cost-consuming. For this reason, this study aims to propose an approach which minimizes the use of such structures. Design/methodology/approach: For minimizing the use of support structures, process parameters in combination with a contour-like exposure strategy are developed to realize support-less overhanging structures of less than 35°. These parameters are implemented in a shell-core strategy, which follows the idea of applying different processing strategies to the critical (overhanging) shell and the uncritical core of the part. Thereby, the core is processed with standard parameters, aiming a dense material. On the critical shell, optimized processing parameters are applied, reaching good results in terms of surface quality, especially at extreme overhang situations. Findings: The results show that the selective laser melting (SLM) technology is able to realize support-less overhanging surfaces by choosing suitable scan strategies and process parameters. Particularly good results are always obtained when the exposure direction of the shell is parallel to the contour of the sample. Originality/value: The validity of the results is demonstrated through the successful reproduction of the build strategy on two commercial SLM machines, reaching support-free builds of surfaces with an angle to the horizontal of less than or equal to 30°.