Jörg Fricke
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jörg Fricke has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Bernd Sumpf
Ferdinand-Braun-Institut (Germany)
3 shared publications G. Erbert
Ferdinand-Braun-Institut (Germany)
3 shared publicationsG. Tränkle
Ferdinand-Braun-Institut (Germany)
3 shared publicationsA. Klehr
Ferdinand-Braun-Institut (Germany)
2 shared publications- Frank Bugge
Ferdinand-Braun-Institut (Germany)
2 shared publications G Erbert
Leibniz-Institut für Höchstfrequenztechnik
2 shared publications
Latest Publications
- Open Access
- 1 May 2018
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 54 (9) , 582-583
Red‐emitting distributed‐feedback ridge‐waveguide laser based on high‐order surface grating
Distributed‐feedback ridge‐waveguide lasers emitting around 670 nm have been fabricated and experimentally characterised. Wavelength stabilisation is provided by 40th Bragg order surface gratings dry‐etched into the p‐GaAs–AlGaAs–AlGaInP layer structure. The large grating period of 4.2 µm allows the injection of the current between the grooves of the grating without sacrificing the electrical and optical properties noticeably. The 1.5 mm long devices achieve an output power of 50 mW at an injection current of 180 mA. The side mode suppression ratio is 50 dB at 150 mA.
- 1 May 2018
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 54 (9) , 582-583
Open AccessRed‐emitting distributed‐feedback ridge‐waveguide laser based on high‐order surface grating
Distributed‐feedback ridge‐waveguide lasers emitting around 670 nm have been fabricated and experimentally characterised. Wavelength stabilisation is provided by 40th Bragg order surface gratings dry‐etched into the p‐GaAs–AlGaAs–AlGaInP layer structure. The large grating period of 4.2 µm allows the injection of the current between the grooves of the grating without sacrificing the electrical and optical properties noticeably. The 1.5 mm long devices achieve an output power of 50 mW at an injection current of 180 mA. The side mode suppression ratio is 50 dB at 150 mA.
- 27 June 2017
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 32 (7) , 075012
DFB lasers with apodized surface gratings for wavelength stabilization and high efficiency
We present results of GaAs-based distributed-feedback (DFB) broad-area (BA) lasers with integrated surface-etched gratings. Lasers with longitudinally varying (apodized) Bragg gratings are compared to lasers with uniform gratings. DFB-BA lasers with apodized gratings show improved conversion efficiency and output power compared to those with uniform gratings. DFB-BA lasers with narrow contact stripe width W = 30 μ m and resonator length L = 6 mm show a peak conversion efficiency of 60% and maintain efficiency >50% to an output power of >6 W. The spectral FWHM linewidth is below 0.5 nm. Furthermore DFB lasers with implemented apodized gratings are less sensitive to fabrication tolerances.
- 27 June 2017
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 32 (7) , 075012
DFB lasers with apodized surface gratings for wavelength stabilization and high efficiency
We present results of GaAs-based distributed-feedback (DFB) broad-area (BA) lasers with integrated surface-etched gratings. Lasers with longitudinally varying (apodized) Bragg gratings are compared to lasers with uniform gratings. DFB-BA lasers with apodized gratings show improved conversion efficiency and output power compared to those with uniform gratings. DFB-BA lasers with narrow contact stripe width W = 30 μ m and resonator length L = 6 mm show a peak conversion efficiency of 60% and maintain efficiency >50% to an output power of >6 W. The spectral FWHM linewidth is below 0.5 nm. Furthermore DFB lasers with implemented apodized gratings are less sensitive to fabrication tolerances.
- 4 March 2015
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9313, 93130Y
Shifted excitation Raman difference spectroscopy using a dual-wavelength DBR diode laser at 785 nm
The application of shifted excitation Raman difference spectroscopy (SERDS) using a dual wavelength distributed Bragg reflector (DBR) diode laser at 785 nm will be presented. Both excitation wavelengths necessary for SERDS provide an optical power of more than 160 mW in continuous wave operation. Raman experiments are carried out and demonstrate the suitability of the excitation light source for SERDS. Moreover, a dual-wavelength master-oscillator power amplifier diode laser system is presented. The diode laser system reaches optical powers larger 750 mW while the spectral properties of the dual-wavelength laser remain unchanged.
- 4 March 2015
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9313, 93130Y
Shifted excitation Raman difference spectroscopy using a dual-wavelength DBR diode laser at 785 nm
The application of shifted excitation Raman difference spectroscopy (SERDS) using a dual wavelength distributed Bragg reflector (DBR) diode laser at 785 nm will be presented. Both excitation wavelengths necessary for SERDS provide an optical power of more than 160 mW in continuous wave operation. Raman experiments are carried out and demonstrate the suitability of the excitation light source for SERDS. Moreover, a dual-wavelength master-oscillator power amplifier diode laser system is presented. The diode laser system reaches optical powers larger 750 mW while the spectral properties of the dual-wavelength laser remain unchanged.
- 11 February 2010
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7616
High-peak-power pulse generation with GHz repetition rate using a Q-switched 1060nm DBR tapered laser
Experimental results from a Q-switched three section tapered laser, with an InGaAs triple quantumwell (TQW) active region, consisting of a 2000 μm long tapered element, a 1000 μm ridge waveguide (RW) section and a 1000 μm long passive grating section with a 6th order surface grating were fabricated and investigated. For the generation of short optical pulses the tapered section was biased with a dc-current and the RW absorber section was modulated by a 1 GHz sinusoidal current. By biasing the tapered section with 4 A cw current and GHz sinusoidal modulation of the RW section, short pulses of ~75 ps width and a pulse power of 6.3 W corresponding to 470 pJ pulse energy is reached. The Q-switched pulses are single mode with a central emission wavelength of ~1064 nm and a FWHM spectral width ≤ 0.05 nm.
- 11 February 2010
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7616
High-peak-power pulse generation with GHz repetition rate using a Q-switched 1060nm DBR tapered laser
Experimental results from a Q-switched three section tapered laser, with an InGaAs triple quantumwell (TQW) active region, consisting of a 2000 μm long tapered element, a 1000 μm ridge waveguide (RW) section and a 1000 μm long passive grating section with a 6th order surface grating were fabricated and investigated. For the generation of short optical pulses the tapered section was biased with a dc-current and the RW absorber section was modulated by a 1 GHz sinusoidal current. By biasing the tapered section with 4 A cw current and GHz sinusoidal modulation of the RW section, short pulses of ~75 ps width and a pulse power of 6.3 W corresponding to 470 pJ pulse energy is reached. The Q-switched pulses are single mode with a central emission wavelength of ~1064 nm and a FWHM spectral width ≤ 0.05 nm.
- 11 February 2010
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7616
Comparison of 650 nm tapered lasers with different lateral geometries at output powers up to 1 W
650 nm tapered laser diodes with nearly diffraction limited beam quality are requested for laser display applications. In this paper, results for 2 mm long 650 nm tapered lasers diodes with different lateral geometries will be presented. The vertical structure is based on a 5 nm thick InGaP single quantum well embedded in AlGaInP waveguide and n- AlInP and p-AlGaAs cladding layers. The ridge waveguides of lengths LRW = 200 μm, 300 μm, 500 μm, and 750 μm were fabricated using selective etching. The contact window for the tapered section was defined applying ion implantation. Devices with a taper angle of 4° were manufactured. The facets were passivated. The rear side was high reflection coated and the taper side anti reflection coated. The devices were mounted p-side down on CVDdiamond heat spreaders and standard C-mounts. All devices reached a maximal output power larger than 1 W. They had a threshold current density of about 700 A/cm2 and a slope efficiency of 0.8 W/A. The best conversion efficiency was 20%. The devices with the shortest RW-length LRW = 200 μm had the best beam quality (beam waist width 7 μm, far field angle 8.8°, 85% of the emitted power in central lobe, M2 of 1.3 (all values measured at 1/e2-level)) at P = 1 W. The beam quality for devices with longer RW-section deteriorates up to M2 = 4.4 for a LRW = 750 μm laser.
- 11 February 2010
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7616
Comparison of 650 nm tapered lasers with different lateral geometries at output powers up to 1 W
650 nm tapered laser diodes with nearly diffraction limited beam quality are requested for laser display applications. In this paper, results for 2 mm long 650 nm tapered lasers diodes with different lateral geometries will be presented. The vertical structure is based on a 5 nm thick InGaP single quantum well embedded in AlGaInP waveguide and n- AlInP and p-AlGaAs cladding layers. The ridge waveguides of lengths LRW = 200 μm, 300 μm, 500 μm, and 750 μm were fabricated using selective etching. The contact window for the tapered section was defined applying ion implantation. Devices with a taper angle of 4° were manufactured. The facets were passivated. The rear side was high reflection coated and the taper side anti reflection coated. The devices were mounted p-side down on CVDdiamond heat spreaders and standard C-mounts. All devices reached a maximal output power larger than 1 W. They had a threshold current density of about 700 A/cm2 and a slope efficiency of 0.8 W/A. The best conversion efficiency was 20%. The devices with the shortest RW-length LRW = 200 μm had the best beam quality (beam waist width 7 μm, far field angle 8.8°, 85% of the emitted power in central lobe, M2 of 1.3 (all values measured at 1/e2-level)) at P = 1 W. The beam quality for devices with longer RW-section deteriorates up to M2 = 4.4 for a LRW = 750 μm laser.
- 20 February 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 15 (3) , 901-908
High-Brightness and Ultranarrow-Beam 850-nm GaAs/AlGaAs Photonic Band Crystal Lasers and Single-Mode Arrays
Lasers with a waveguide based on a longitudinal photonic band crystal designed for 850 nm emission are investigated. They demonstrate ultranarrow vertical beam divergence of about 7deg full-width at half maximum without using corrective optics. A high internal efficiency of 93% is achieved. Broad-area 50-mum-wide stripe lasers with unpassivated facets show a high total output power of about 20 W in pulsed mode with far-field divergences of 9.5deg and 11.3deg of the slow and fast axis, respectively, equivalent to an ultrahigh brightness of 3×10 8 Wmiddotcm -2 middotsr -1 and a low aspect ratio of only 1.2. Narrow ridge lasers with 5 mum stripes demonstrate more than 1.5 W maximum output power in continuous-wave operation. Large arrays with up to 256 uncoupled single-mode laser diodes demonstrate low threshold currents of about 70 mA per laser, independent of the number of lasers in the array.
- 20 February 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 15 (3) , 901-908
High-Brightness and Ultranarrow-Beam 850-nm GaAs/AlGaAs Photonic Band Crystal Lasers and Single-Mode Arrays
Lasers with a waveguide based on a longitudinal photonic band crystal designed for 850 nm emission are investigated. They demonstrate ultranarrow vertical beam divergence of about 7deg full-width at half maximum without using corrective optics. A high internal efficiency of 93% is achieved. Broad-area 50-mum-wide stripe lasers with unpassivated facets show a high total output power of about 20 W in pulsed mode with far-field divergences of 9.5deg and 11.3deg of the slow and fast axis, respectively, equivalent to an ultrahigh brightness of 3×10 8 Wmiddotcm -2 middotsr -1 and a low aspect ratio of only 1.2. Narrow ridge lasers with 5 mum stripes demonstrate more than 1.5 W maximum output power in continuous-wave operation. Large arrays with up to 256 uncoupled single-mode laser diodes demonstrate low threshold currents of about 70 mA per laser, independent of the number of lasers in the array.
- 18 February 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 15 (3) , 978-983
High-Power DBR-Tapered Laser at 980 nm for Single-Path Second Harmonic Generation
We present experimental results about edge-emitting distributed-Bragg-reflector-tapered diode lasers emitting at 980 nm. The investigated lasers show an output power of up to 12 W with a conversion efficiency of about 45%. The lasers also exhibit a small vertical divergence <15deg full-width at half maximum (FWHM), a nearly diffraction-limited beam quality, and a narrow spectral linewidth with FWHM smaller than 12 pm. These properties allow efficient single-pass second harmonic generation with power levels of more than 1 W at 488 nm.
- 18 February 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 15 (3) , 978-983
High-Power DBR-Tapered Laser at 980 nm for Single-Path Second Harmonic Generation
We present experimental results about edge-emitting distributed-Bragg-reflector-tapered diode lasers emitting at 980 nm. The investigated lasers show an output power of up to 12 W with a conversion efficiency of about 45%. The lasers also exhibit a small vertical divergence <15deg full-width at half maximum (FWHM), a nearly diffraction-limited beam quality, and a narrow spectral linewidth with FWHM smaller than 12 pm. These properties allow efficient single-pass second harmonic generation with power levels of more than 1 W at 488 nm.