Sripriyan Karuthapandi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sripriyan Karuthapandi has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Ramu Murugan
Department of Mechanical Engineering, Amrita School of Engineering, Amrita Vishwa Vidyapeetham, Coimbatore, India
4 shared publications - M. Karthigha
Department of Computer Science and Engineering, PSG Institute of Technology and Applied Research, Neelambur, India
3 shared publications P. R. Thyla
Department of Mechanical Engineering, PSG College of Technology, Coimbatore, India
3 shared publicationsK. Anantharuban
Department of Production, Tata Global Beverage Limited, Munnar, India
2 shared publicationsM Ramu
Amrita School of Engineering, Amirta Vishwa Vidyapeetham University
2 shared publicationsM. Ramu
Department of Mechanical Engineering, Amrita School of Engineering, Amirta Vishwa Vidyapeetham University, Coimbatore, India
2 shared publications
Latest Publications
- 24 January 2026
- Published by Springer Nature
- p. 667-677
Mechanical and Metallurgical Characteristics of Dissimilar Friction Stir T-Joint Dissimilar Materials of AA 6061-T6 and AA 5052-O Alloys
- 24 January 2026
- Published by Springer Nature
- p. 667-677
Mechanical and Metallurgical Characteristics of Dissimilar Friction Stir T-Joint Dissimilar Materials of AA 6061-T6 and AA 5052-O Alloys
- 24 January 2026
- Published by Springer Nature
- p. 141-155
Deep Learning for Network Intrusion Detection: Attention-Based Bidirectional Modified Gated Recurrent Unit
- 24 January 2026
- Published by Springer Nature
- p. 141-155
Deep Learning for Network Intrusion Detection: Attention-Based Bidirectional Modified Gated Recurrent Unit
- 5 December 2024
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 38 (12) , 6791-6798
A comparative study on the microstructures and mechanical properties of arc welded of HSLA steel
- 5 December 2024
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 38 (12) , 6791-6798
A comparative study on the microstructures and mechanical properties of arc welded of HSLA steel
- Open Access
- 10 July 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-14
Influence of granite micro particles on the mechanical, damping and antimicrobial properties of silk–sisal hybrid composites
This paper focuses on the effect of granite-micro-filler on static mechanical properties, damping behavior, and physical characteristics of silk-sisal hybrid composite. The composites structures are fabricated by using three layers of plain weaves mat with varying weight percentages (2, 4, and 6 wt%) of granite-micro-filler by hand layer process. The effect of granite-micro-filler on silk-sisal is analyzed and results are compared with pure silk-sisal (without granite-Micro-filler) hybrid composite. The results infer that; the tensile strength and flexural strength value of the developed silk-sisal hybrid composites are increased with the increase in wt% of granite-micro-filler content than pure silk–sisal, approximately 5% and 9% improved value in order by adding 6 wt% granite-micro-filler on silk–sisal. The tensile and flexural fracture morphology analysis indicated that composed plain weave of silk–sisal fiber mat with two (longitudinal and transverse) directions possesses higher mechanical properties and also observed that, granite-micro-filler dispersed on silk–sisal fiber mat and resin with closely packed. The improved damping factor is obtained by adding 6 wt% of granite-micro-filler content, which is approximately 75.8% higher than pure silk–sisal. The physical properties of silk–sisal hybrid composite have also been analyzed and well discussed in this paper.
- 10 July 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-14
Open AccessInfluence of granite micro particles on the mechanical, damping and antimicrobial properties of silk–sisal hybrid composites
This paper focuses on the effect of granite-micro-filler on static mechanical properties, damping behavior, and physical characteristics of silk-sisal hybrid composite. The composites structures are fabricated by using three layers of plain weaves mat with varying weight percentages (2, 4, and 6 wt%) of granite-micro-filler by hand layer process. The effect of granite-micro-filler on silk-sisal is analyzed and results are compared with pure silk-sisal (without granite-Micro-filler) hybrid composite. The results infer that; the tensile strength and flexural strength value of the developed silk-sisal hybrid composites are increased with the increase in wt% of granite-micro-filler content than pure silk–sisal, approximately 5% and 9% improved value in order by adding 6 wt% granite-micro-filler on silk–sisal. The tensile and flexural fracture morphology analysis indicated that composed plain weave of silk–sisal fiber mat with two (longitudinal and transverse) directions possesses higher mechanical properties and also observed that, granite-micro-filler dispersed on silk–sisal fiber mat and resin with closely packed. The improved damping factor is obtained by adding 6 wt% of granite-micro-filler content, which is approximately 75.8% higher than pure silk–sisal. The physical properties of silk–sisal hybrid composite have also been analyzed and well discussed in this paper.
- Open Access
- 16 February 2024
- Published by Springer Nature in Research Square
Investigating the Mechanical and Physical Enhancements of Silk-sisal Hybrid Composites Through Granite-nano-filler Integration: Synergizing Strength, Damping, and Form
This paper focuses on the effect of granite-nano-filler on static mechanical properties, damping behavior, and physical characteristics of silk-sisal hybrid composite. The composites structures are fabricated by using three layers of plain weaves mat with varying weight percentages (2, 4, and 6 wt. %) of granite-nano-filler by hand layer process. The effect of granite-nano-filler on silk-sisal is analyzed and results are compared with pure silk-sisal (without granite-nano-filler) hybrid composite. The results infer that; the tensile strength and flexural strength value of the developed silk-sisal hybrid composites are increased with the increase in wt.% of granite-nano-filler content than pure silk-sisal, approximately 5% and 9% improved value in order by adding 6 wt. % granite-nano-filler on silk-sisal. The tensile and flexural fracture morphology analysis indicated that composed plain weave of silk-sisal fiber mat with two (longitudinal and transverse) directions possesses higher mechanical properties and also observed that, granite-nano-filler dispersed on silk-sisal fiber mat and resin with closely packed. The improved damping factor is obtained by adding 6 wt. % of granite-nano-filler content, which is approximately 75.8% higher than pure silk-sisal. The physical properties of silk-sisal hybrid composite have also been analyzed and well discussed in this paper.
- 16 February 2024
- Published by Springer Nature in Research Square
Open AccessInvestigating the Mechanical and Physical Enhancements of Silk-sisal Hybrid Composites Through Granite-nano-filler Integration: Synergizing Strength, Damping, and Form
This paper focuses on the effect of granite-nano-filler on static mechanical properties, damping behavior, and physical characteristics of silk-sisal hybrid composite. The composites structures are fabricated by using three layers of plain weaves mat with varying weight percentages (2, 4, and 6 wt. %) of granite-nano-filler by hand layer process. The effect of granite-nano-filler on silk-sisal is analyzed and results are compared with pure silk-sisal (without granite-nano-filler) hybrid composite. The results infer that; the tensile strength and flexural strength value of the developed silk-sisal hybrid composites are increased with the increase in wt.% of granite-nano-filler content than pure silk-sisal, approximately 5% and 9% improved value in order by adding 6 wt. % granite-nano-filler on silk-sisal. The tensile and flexural fracture morphology analysis indicated that composed plain weave of silk-sisal fiber mat with two (longitudinal and transverse) directions possesses higher mechanical properties and also observed that, granite-nano-filler dispersed on silk-sisal fiber mat and resin with closely packed. The improved damping factor is obtained by adding 6 wt. % of granite-nano-filler content, which is approximately 75.8% higher than pure silk-sisal. The physical properties of silk-sisal hybrid composite have also been analyzed and well discussed in this paper.
- 4 October 2022
- Published by Springer Nature
- p. 617-629
Numerical Investigation on Phase Change Material (PCM) for Thermal Management Buildings Using Design-Builder Software
- 4 October 2022
- Published by Springer Nature
- p. 617-629
Numerical Investigation on Phase Change Material (PCM) for Thermal Management Buildings Using Design-Builder Software
- Open Access
- 17 September 2021
- Published by Springer Nature in Research Square
Characteristic of Weld Bead By Using Flat Wire Electrode In GMAW Inline During The Process: An Experimental And Numerical Analysis
This paper focusses on effect of flat wire electrode on gas metal arc welding (FW-GMAW) inline during the process to improve quality of weld bead. Since the flat wire electrode perimeter has enlarged, the turbulence of the molten droplet characteristics is altered due to the effect of electromagnetic force. To bring out, butt joint welding are proven with use of the flat wire electrode. The experimental results indicated that, the flat wire electrode and their orientations are significantly factors to improve the weld bead dimensions, due to the increased in steady state temperature and heat density. The end result also evident that the depth-to-width (D/W) ratio was improved on an average by 7.7 % than regular wire electrode used in GMAW. To validate, a comprehensive numerical model was developed, the result confirmed that the initial arc and steady state temperature are high for FW-GMAW. In addition, improvements in metallurgical and mechanical properties are discussed in this paper.
- 17 September 2021
- Published by Springer Nature in Research Square
Open AccessCharacteristic of Weld Bead By Using Flat Wire Electrode In GMAW Inline During The Process: An Experimental And Numerical Analysis
This paper focusses on effect of flat wire electrode on gas metal arc welding (FW-GMAW) inline during the process to improve quality of weld bead. Since the flat wire electrode perimeter has enlarged, the turbulence of the molten droplet characteristics is altered due to the effect of electromagnetic force. To bring out, butt joint welding are proven with use of the flat wire electrode. The experimental results indicated that, the flat wire electrode and their orientations are significantly factors to improve the weld bead dimensions, due to the increased in steady state temperature and heat density. The end result also evident that the depth-to-width (D/W) ratio was improved on an average by 7.7 % than regular wire electrode used in GMAW. To validate, a comprehensive numerical model was developed, the result confirmed that the initial arc and steady state temperature are high for FW-GMAW. In addition, improvements in metallurgical and mechanical properties are discussed in this paper.
- 23 July 2021
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 35 (8) , 3771
Erratum to “Weld bead characterization of flat wire electrode in gmaw process part II: a numerical study”
- 23 July 2021
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 35 (8) , 3771
Erratum to “Weld bead characterization of flat wire electrode in gmaw process part II: a numerical study”