Miloš Stanković
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Miloš Stanković has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Aleksandar Grbović
University of Belgrade
1 shared publication - Aleksandar Marinković
Faculty of Mechanical Engineering, University of Belgrade, 11000 Belgrade, Serbia
1 shared publication Aleksandar Simonovic
1 shared publication- Aleksandar Vencl
University of Belgrade, Faculty of Mechanical Engineering, Kraljice Marije 16, 11120 Belgrade, Serbia
1 shared publication - Biljana Bobić
Institute of Chemistry University of Belgrade Technology and Metallurgy Belgrade Serbia
1 shared publication - Blaža Stojanović
Faculty of Engineering, University of Kragujevac, Sestre Janjić 6, 34000 Kragujevac, Serbia
1 shared publication
Latest Publications
- 23 November 2023
- Published by Springer Nature
- p. 291-303
Flow Analysis Inside the Blade of Tip-Jet Cold Cycle Helicopter
- 23 November 2023
- Published by Springer Nature
- p. 291-303
Flow Analysis Inside the Blade of Tip-Jet Cold Cycle Helicopter
- 6 February 2020
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 42 (3) , 1-12
Influence of secondary phases in A356 MMCs on their mechanical properties at macro- and nanoscale
- 6 February 2020
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 42 (3) , 1-12
Influence of secondary phases in A356 MMCs on their mechanical properties at macro- and nanoscale
- 14 January 2019
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 71 (1) , 119-125
Determination of Archard’s wear coefficient and wear simulation of sliding bearings
Purpose: This paper aims to present the methodology to determine Archard’s wear coefficient. By applying this coefficient into the numerical simulation of wear, it is possible to predict wear without long lasting and usually expensive experiments. Design/methodology/approach: To determine necessary particles of Archard’s equation and calculate wear coefficient K, an experimental investigation is proposed. Afterwards, the wear simulation is executed in FEM software ANSYS 18.1. Analytical method is offered to determine worn volume for cylinder-in-cylinder contact, based on “inclination” of inner cylinder. Findings: Comparing the value of Archard’s coefficient obtained by this experimental investigation with the values from the literature for the similar materials, high correlation is noted. Furthermore, numerically calculated contact pressure is confirmed with analytical method. Trend of pressure decrease due to wearing process, as well as due to increase of contact surface is observed. Practical implications: Since the prediction of the wear is closely related to the life cycle assessment of bearings, and the machines in general, it has significant practical importance for designers. Originality/value: Determination of Archard’s coefficient is usually performed by conventional pin-on-disk tribometers. This methodology offers a different approach for the determination of Archard’s wear coefficient for cylinder-in-cylinder contact, which is convenient for shaft-sliding bearing contact.
- 14 January 2019
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 71 (1) , 119-125
Determination of Archard’s wear coefficient and wear simulation of sliding bearings
Purpose: This paper aims to present the methodology to determine Archard’s wear coefficient. By applying this coefficient into the numerical simulation of wear, it is possible to predict wear without long lasting and usually expensive experiments. Design/methodology/approach: To determine necessary particles of Archard’s equation and calculate wear coefficient K, an experimental investigation is proposed. Afterwards, the wear simulation is executed in FEM software ANSYS 18.1. Analytical method is offered to determine worn volume for cylinder-in-cylinder contact, based on “inclination” of inner cylinder. Findings: Comparing the value of Archard’s coefficient obtained by this experimental investigation with the values from the literature for the similar materials, high correlation is noted. Furthermore, numerically calculated contact pressure is confirmed with analytical method. Trend of pressure decrease due to wearing process, as well as due to increase of contact surface is observed. Practical implications: Since the prediction of the wear is closely related to the life cycle assessment of bearings, and the machines in general, it has significant practical importance for designers. Originality/value: Determination of Archard’s coefficient is usually performed by conventional pin-on-disk tribometers. This methodology offers a different approach for the determination of Archard’s wear coefficient for cylinder-in-cylinder contact, which is convenient for shaft-sliding bearing contact.
- 1 January 2017
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 45 (3) , 441-447
Buckling behaviour of dented aluminium alloy cylindrical shell subjected to uniform axial compression
Thin-walled cylindrical shells are commonly used in numerous branches of industry. Since they are subjected to axial load, the most common cause of their failure is buckling. This paper provides numerical analysis and experimental verification of the buckling of the thin-walled aluminium alloy cylindrical shell with special regard to the influence of dent, positioned in the middle of the shell. Numerical simulation was performed using ANSYS 16.2, and experimental verification was performed by means of hydraulic press Armavir, PSU-50, which was used to subject the specimen to the increasing axial load until the occurrence of buckling. Comparing the results it was concluded that there is significant decrease of the buckling resistance if compared the values of the specimen with no dent, and the specimen with 2 mm deep dent. On the contrary, resistance of the 2 mm and 4 mm dented specimen is quite similar. Position and shape of the deformations occurred due to buckling are matching if experimental and numerical results are compared.
- 1 January 2017
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 45 (3) , 441-447
Buckling behaviour of dented aluminium alloy cylindrical shell subjected to uniform axial compression
Thin-walled cylindrical shells are commonly used in numerous branches of industry. Since they are subjected to axial load, the most common cause of their failure is buckling. This paper provides numerical analysis and experimental verification of the buckling of the thin-walled aluminium alloy cylindrical shell with special regard to the influence of dent, positioned in the middle of the shell. Numerical simulation was performed using ANSYS 16.2, and experimental verification was performed by means of hydraulic press Armavir, PSU-50, which was used to subject the specimen to the increasing axial load until the occurrence of buckling. Comparing the results it was concluded that there is significant decrease of the buckling resistance if compared the values of the specimen with no dent, and the specimen with 2 mm deep dent. On the contrary, resistance of the 2 mm and 4 mm dented specimen is quite similar. Position and shape of the deformations occurred due to buckling are matching if experimental and numerical results are compared.