Arthur Slobbe
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Arthur Slobbe has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Árpád Rózsás
Department of Structural Reliability Netherlands Organization for Applied Scientific Research (TNO) Delft The Netherlands
5 shared publications - Agnieszka Bigaj‐Van Vliet
Netherlands Organization for Applied Scientific Research (TNO)
2 shared publications Diego Allaix
Netherlands Organization for Applied Scientific Research (TNO)
2 shared publicationsYuguang Yang
Faculty of Civil Engineering and Geosciences Delft University of Technology Delft Netherlands
2 shared publicationsAgnieszka Bigaj van Vliet
Netherlands Organization for Applied Scientific Research (TNO)
1 shared publication- Alice Cicirello
Department of Engineering, University of Cambridge
1 shared publication
Latest Publications
- 24 May 2026
- Published by Wiley in Structural Concrete
Impact of creep and shrinkage models in predicting deflection and prestress losses of balanced cantilever box girder bridges: A case study with multi‐decade deflection measurements
Current code‐based models for concrete creep and shrinkage present significant challenges when applied to large structures such as balanced cantilever box girder bridges, due to their complex geometry and staged construction. Case studies on such structures with multi‐decade deflection measurements, though scarce in literature, are essential for evaluating the long‐term accuracy of these models. This paper presents a unique case study of a three‐span balanced cantilever box girder bridge in the Netherlands with 44 years of deflection measurements, revealing excessive and ongoing deflections. A detailed finite element model incorporating construction stages was developed to study the impact of four creep and shrinkage models on the predictions of multi‐decade deflections and prestress losses. All models significantly underestimated long‐term deflections, by about 75% for Eurocode 2 (2004), Eurocode 2 (2023), and fib Model Code 2010, and 35% for RILEM B4. The choice of the creep and shrinkage model also strongly affects the predicted prestress losses, with RILEM B4 estimating losses up to 1.7 times higher than Eurocode 2 (2004). Since the working prestress level is a key factor for structural assessment of large‐span concrete bridges, these findings have important implications for engineering practice. Supported by rare long‐term validation data, this study reveals the performance and limitations of current creep and shrinkage models, the possible consequences of their underestimations, and the need for more reliable long‐term prediction models for the design and assessment of box girder bridges.
- 24 May 2026
- Published by Wiley in Structural Concrete
Impact of creep and shrinkage models in predicting deflection and prestress losses of balanced cantilever box girder bridges: A case study with multi‐decade deflection measurements
Current code‐based models for concrete creep and shrinkage present significant challenges when applied to large structures such as balanced cantilever box girder bridges, due to their complex geometry and staged construction. Case studies on such structures with multi‐decade deflection measurements, though scarce in literature, are essential for evaluating the long‐term accuracy of these models. This paper presents a unique case study of a three‐span balanced cantilever box girder bridge in the Netherlands with 44 years of deflection measurements, revealing excessive and ongoing deflections. A detailed finite element model incorporating construction stages was developed to study the impact of four creep and shrinkage models on the predictions of multi‐decade deflections and prestress losses. All models significantly underestimated long‐term deflections, by about 75% for Eurocode 2 (2004), Eurocode 2 (2023), and fib Model Code 2010, and 35% for RILEM B4. The choice of the creep and shrinkage model also strongly affects the predicted prestress losses, with RILEM B4 estimating losses up to 1.7 times higher than Eurocode 2 (2004). Since the working prestress level is a key factor for structural assessment of large‐span concrete bridges, these findings have important implications for engineering practice. Supported by rare long‐term validation data, this study reveals the performance and limitations of current creep and shrinkage models, the possible consequences of their underestimations, and the need for more reliable long‐term prediction models for the design and assessment of box girder bridges.
- Open Access
- 29 January 2026
- Published by Elsevier in Computers & Structures
- Vol. 322
Modelling interface damage in masonry structures under cyclic loading conditions with cohesive fracture and regularized friction
- 29 January 2026
- Published by Elsevier in Computers & Structures
- Vol. 322
Open AccessModelling interface damage in masonry structures under cyclic loading conditions with cohesive fracture and regularized friction
- 29 December 2024
- Published by Springer Nature
- p. 186-194
Finite Element Analysis of the Time-Dependent Behavior and Prestress Losses in Recycled Aggregate Concrete Beams
- 29 December 2024
- Published by Springer Nature
- p. 186-194
Finite Element Analysis of the Time-Dependent Behavior and Prestress Losses in Recycled Aggregate Concrete Beams
- 13 December 2024
- Published by Springer Nature
- p. 93-110
Automated Image Segmentation and Quantification of Settlement for Masonry Buildings Using Foundation Deep Learning
- 13 December 2024
- Published by Springer Nature
- p. 93-110
Automated Image Segmentation and Quantification of Settlement for Masonry Buildings Using Foundation Deep Learning
- Open Access
Bayesian system identification for structures considering spatial and temporal correlation
The decreasing cost and improved sensor and monitoring system technology (e.g. fiber optics and strain gauges) have led to more measurements in close proximity to each other. When using such spatially dense measurement data in Bayesian system identification strategies, the correlation in the model prediction error can become significant. The widely adopted assumption of uncorrelated Gaussian error may lead to inaccurate parameter estimation and overconfident predictions, which may lead to sub-optimal decisions. This paper addresses the challenges of performing Bayesian system identification for structures when large datasets are used, considering both spatial and temporal dependencies in the model uncertainty. We present an approach to efficiently evaluate the log-likelihood function, and we utilize nested sampling to compute the evidence for Bayesian model selection. The approach is first demonstrated on a synthetic case and then applied to a (measured) real-world steel bridge. The results show that the assumption of dependence in the model prediction uncertainties is decisively supported by the data. The proposed developments enable the use of large datasets and accounting for the dependency when performing Bayesian system identification, even when a relatively large number of uncertain parameters is inferred.
Open AccessBayesian system identification for structures considering spatial and temporal correlation
The decreasing cost and improved sensor and monitoring system technology (e.g. fiber optics and strain gauges) have led to more measurements in close proximity to each other. When using such spatially dense measurement data in Bayesian system identification strategies, the correlation in the model prediction error can become significant. The widely adopted assumption of uncorrelated Gaussian error may lead to inaccurate parameter estimation and overconfident predictions, which may lead to sub-optimal decisions. This paper addresses the challenges of performing Bayesian system identification for structures when large datasets are used, considering both spatial and temporal dependencies in the model uncertainty. We present an approach to efficiently evaluate the log-likelihood function, and we utilize nested sampling to compute the evidence for Bayesian model selection. The approach is first demonstrated on a synthetic case and then applied to a (measured) real-world steel bridge. The results show that the assumption of dependence in the model prediction uncertainties is decisively supported by the data. The proposed developments enable the use of large datasets and accounting for the dependency when performing Bayesian system identification, even when a relatively large number of uncertain parameters is inferred.
- 3 June 2023
- Published by Springer Nature
- p. 520-530
Finite Element Modeling of Shear Failure in Prestressed Girders with a Continuous Cast-In-Situ Deck Slab
- 3 June 2023
- Published by Springer Nature
- p. 520-530
Finite Element Modeling of Shear Failure in Prestressed Girders with a Continuous Cast-In-Situ Deck Slab
- 14 December 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (2) , 2979-3001
Reliability‐based calibration of design code formulas: Application to shear resistance formulas for reinforced concrete members without shear reinforcement
This paper presents a reliability‐based calibration method for design code formulas. The method is demonstrated on the shear design formulas in Eurocode 2 and fib Model Code 2010 (MC2010). We found that the partial factor in the current Eurocode 2 is about 20% lower than the optimal value and, thus, provides an insufficient safety margin. The obtained optimal partial factor in the (modified) Eurocode 2 and MC2010 formulas is 1.53 and 1.36, respectively. The difference stems from higher accuracy and, hence, lower uncertainty of the MC2010 model in predicting experimental results. Hence, on average, the MC2010 formula leads to about 13% larger design resistances compared to Eurocode 2 given that the target reliability for both design formulas is the same. To stimulate and facilitate future structural code development and derivation of partial factors, we make the used computer code freely available.
- 14 December 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (2) , 2979-3001
Reliability‐based calibration of design code formulas: Application to shear resistance formulas for reinforced concrete members without shear reinforcement
This paper presents a reliability‐based calibration method for design code formulas. The method is demonstrated on the shear design formulas in Eurocode 2 and fib Model Code 2010 (MC2010). We found that the partial factor in the current Eurocode 2 is about 20% lower than the optimal value and, thus, provides an insufficient safety margin. The obtained optimal partial factor in the (modified) Eurocode 2 and MC2010 formulas is 1.53 and 1.36, respectively. The difference stems from higher accuracy and, hence, lower uncertainty of the MC2010 model in predicting experimental results. Hence, on average, the MC2010 formula leads to about 13% larger design resistances compared to Eurocode 2 given that the target reliability for both design formulas is the same. To stimulate and facilitate future structural code development and derivation of partial factors, we make the used computer code freely available.
- 3 April 2022
- Published by Wiley in Structural Concrete
- Vol. 23 (6) , 3569-3600
Structural and load parameter estimation of a real‐world reinforced concrete slab bridge using measurements and Bayesian statistics
This paper describes a static diagnostic load testing and measurement campaign of a reinforced concrete road bridge in Amsterdam. We consider 29 vertical translation sensors and 37 strain sensors. Multiple Bayesian parameter estimations are performed to estimate two structural and two load parameters of a three‐dimensional finite element (FE) model. The structural parameters are the concrete elastic modulus of the deck and the rotational spring stiffness at the piers. The load (truck) parameters are the load mass and position, which are estimated from separate measurements. We found that estimating (updating) the two selected structural parameters considerably improves the vertical translation model prediction accuracy over the FE model that was built before the measurement campaign, that is, the R2 score increases from 0.90 to 0.98. Moreover, the load (truck) mass and position parameters can be estimated with high accuracy and high precision. When all measurements are used, the load mass and position are estimated with an error, respectively, less than 1.5 tonnes and 0.5 m with respect to the ground truth. On the negative side: when only certain strain measurements are used, the 90% posterior credible interval is about 3 m and 10 tonnes off the ground truth. Although the results are promising, they are restricted to the considered case and, more importantly, to operational loading conditions where the loading is well controlled. All data, models, and code are freely available upon request.
- 3 April 2022
- Published by Wiley in Structural Concrete
- Vol. 23 (6) , 3569-3600
Structural and load parameter estimation of a real‐world reinforced concrete slab bridge using measurements and Bayesian statistics
This paper describes a static diagnostic load testing and measurement campaign of a reinforced concrete road bridge in Amsterdam. We consider 29 vertical translation sensors and 37 strain sensors. Multiple Bayesian parameter estimations are performed to estimate two structural and two load parameters of a three‐dimensional finite element (FE) model. The structural parameters are the concrete elastic modulus of the deck and the rotational spring stiffness at the piers. The load (truck) parameters are the load mass and position, which are estimated from separate measurements. We found that estimating (updating) the two selected structural parameters considerably improves the vertical translation model prediction accuracy over the FE model that was built before the measurement campaign, that is, the R2 score increases from 0.90 to 0.98. Moreover, the load (truck) mass and position parameters can be estimated with high accuracy and high precision. When all measurements are used, the load mass and position are estimated with an error, respectively, less than 1.5 tonnes and 0.5 m with respect to the ground truth. On the negative side: when only certain strain measurements are used, the 90% posterior credible interval is about 3 m and 10 tonnes off the ground truth. Although the results are promising, they are restricted to the considered case and, more importantly, to operational loading conditions where the loading is well controlled. All data, models, and code are freely available upon request.
- 1 February 2022
- Published by Elsevier in Computers and Geotechnics
- Vol. 142
Probabilistic parameter estimation and reliability assessment of a simulated sheet pile wall system
- 1 February 2022
- Published by Elsevier in Computers and Geotechnics
- Vol. 142
Probabilistic parameter estimation and reliability assessment of a simulated sheet pile wall system
- 25 June 2019
- Published by Wiley in Structural Concrete
- Vol. 21 (1) , 32-47
On the value of a reliability‐based nonlinear finite element analysis approach in the assessment of concrete structures
The objective of this paper is to explore the value of reliability‐based nonlinear finite element analysis (NLFEA) over the currently available, standardized assessment methods. To our knowledge, no studies are available on this subject, and this paper provides a first insight into the value and reliability level of these assessment methods. The exploration is illustrated through three reinforced concrete structural members: a continuous girder, a continuous deep beam, and a high‐strength deep beam. The analysis is performed gradually: step by step advancing the approximation level of the mechanical and the probabilistic models. The added value of the reliability‐based NLFEA over the semi‐probabilistic Eurocode (EC) method is found to be on average 0.60. In other words: even if according to the semi‐probabilistic EC method the design action (Ed) is 60% higher than the design resistance (Rd), the compliance with the target reliability criterion can be demonstrated by a reliability‐based NLFEA. Furthermore, it is observed that the gain and its cause (i.e., more advanced mechanical or probabilistic models) are different for the three cases. Though this outcome is restricted to the analyzed cases and should be interpreted as an upper limit added value, it indicates that a more detailed physical representation of the problem and an explicit treatment of uncertainties may uncover substantial reserves compared with the currently available, standardized assessment methods. Hence, the reliability‐based NLFEA method offers a promising alternative in the assessment of existing structures, enabling to avoid expensive measures that might be needed based on simplified methods.
- 25 June 2019
- Published by Wiley in Structural Concrete
- Vol. 21 (1) , 32-47
On the value of a reliability‐based nonlinear finite element analysis approach in the assessment of concrete structures
The objective of this paper is to explore the value of reliability‐based nonlinear finite element analysis (NLFEA) over the currently available, standardized assessment methods. To our knowledge, no studies are available on this subject, and this paper provides a first insight into the value and reliability level of these assessment methods. The exploration is illustrated through three reinforced concrete structural members: a continuous girder, a continuous deep beam, and a high‐strength deep beam. The analysis is performed gradually: step by step advancing the approximation level of the mechanical and the probabilistic models. The added value of the reliability‐based NLFEA over the semi‐probabilistic Eurocode (EC) method is found to be on average 0.60. In other words: even if according to the semi‐probabilistic EC method the design action (Ed) is 60% higher than the design resistance (Rd), the compliance with the target reliability criterion can be demonstrated by a reliability‐based NLFEA. Furthermore, it is observed that the gain and its cause (i.e., more advanced mechanical or probabilistic models) are different for the three cases. Though this outcome is restricted to the analyzed cases and should be interpreted as an upper limit added value, it indicates that a more detailed physical representation of the problem and an explicit treatment of uncertainties may uncover substantial reserves compared with the currently available, standardized assessment methods. Hence, the reliability‐based NLFEA method offers a promising alternative in the assessment of existing structures, enabling to avoid expensive measures that might be needed based on simplified methods.