Jiří Rozbroj
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jiří Rozbroj has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Jan Nečas
CEET, ENET Centre, VSB - Technical University of Ostrava, Ostrava, Czech Republic
13 shared publications - Jakub Hlosta
CEET, ENET Centre, VSB - Technical University of Ostrava, Ostrava, Czech Republic
11 shared publications - Jiří Zegzulka
Department of Mining Engineering and Safety, Faculty of Mining and Geology, VSB-Technical University of Ostrava, 17. listopadu 15/2172, 708 00 Ostrava, Czech Republic
11 shared publications - David Žurovec
Department of Mining Engineering and Safety, Faculty of Mining and Geology, VSB-Technical University of Ostrava, 17. listopadu 15/2172, 708 00 Ostrava, Czech Republic
10 shared publications - Lucie Jezerska
VSB-Technical University of Ostrava, CEET, CENET
6 shared publications - Daniel Gelnar
Technical University of Ostrava
3 shared publications
Latest Publications
- Open Access
Relationship Between Powder Flowability and Abrasive Discharge in an Industrial Metering Valve
Efficient abrasive blasting requires precise control of abrasive mass flow, which is governed by both the metering system design and the flow properties of the abrasive material. This study investigates the influence of particle size distribution on the flow behaviour of brown fused alumina during discharge through a commercially available Thomson TV II metering valve. Four abrasive fractions (F220, F80, F46 and F24) were characterized in terms of particle size distribution, bulk density, moisture content, angle of internal friction, and flow function. The discharge behaviour was experimentally evaluated using a custom-built test stand for four valve opening positions. The results showed that the smallest valve opening caused unstable flow conditions, arching, and complete flow blockage for the coarsest fraction, whereas stable and repeatable discharge was achieved for various valve openings. Although the finest fraction exhibited the highest flowability according to the flow function, it did not achieve the highest mass flow rate, indicating that flowability alone was insufficient to explain the observed discharge performance. Instead, the F80 fraction provided the highest discharge performance under all stable operating conditions. These findings indicate that laboratory flowability indices alone cannot reliably predict abrasive feeding performance and should be evaluated together with bulk density and particle size distribution. The results provide practical guidelines for optimizing abrasive metering systems and contribute to improved process stability, abrasive utilization, and operational efficiency in automated abrasive blasting applications.
Open AccessRelationship Between Powder Flowability and Abrasive Discharge in an Industrial Metering Valve
Efficient abrasive blasting requires precise control of abrasive mass flow, which is governed by both the metering system design and the flow properties of the abrasive material. This study investigates the influence of particle size distribution on the flow behaviour of brown fused alumina during discharge through a commercially available Thomson TV II metering valve. Four abrasive fractions (F220, F80, F46 and F24) were characterized in terms of particle size distribution, bulk density, moisture content, angle of internal friction, and flow function. The discharge behaviour was experimentally evaluated using a custom-built test stand for four valve opening positions. The results showed that the smallest valve opening caused unstable flow conditions, arching, and complete flow blockage for the coarsest fraction, whereas stable and repeatable discharge was achieved for various valve openings. Although the finest fraction exhibited the highest flowability according to the flow function, it did not achieve the highest mass flow rate, indicating that flowability alone was insufficient to explain the observed discharge performance. Instead, the F80 fraction provided the highest discharge performance under all stable operating conditions. These findings indicate that laboratory flowability indices alone cannot reliably predict abrasive feeding performance and should be evaluated together with bulk density and particle size distribution. The results provide practical guidelines for optimizing abrasive metering systems and contribute to improved process stability, abrasive utilization, and operational efficiency in automated abrasive blasting applications.
- Open Access
- 14 September 2025
- Published by Elsevier in Open Ceramics
- Vol. 24
Rheological characterization of clay–refractory waste composites for direct ink writing of ceramic structures
- 14 September 2025
- Published by Elsevier in Open Ceramics
- Vol. 24
Open AccessRheological characterization of clay–refractory waste composites for direct ink writing of ceramic structures
- 1 June 2021
- Published by VSB - Technical University of Ostrava in GeoScience Engineering
- Vol. 67 (2) , 47-51
The Effect of Setting the Operating Conditions of the Sampling Device on the Representative Sample of Coal
- 1 June 2021
- Published by VSB - Technical University of Ostrava in GeoScience Engineering
- Vol. 67 (2) , 47-51
The Effect of Setting the Operating Conditions of the Sampling Device on the Representative Sample of Coal
- 1 March 2021
- Published by Elsevier in Chemical Engineering Research and Design
- Vol. 167, 25-36
Effective use of DEM to design chain conveyor geometry
- 1 March 2021
- Published by Elsevier in Chemical Engineering Research and Design
- Vol. 167, 25-36
Effective use of DEM to design chain conveyor geometry
- Open Access
DEM Investigation of the Influence of Particulate Properties and Operating Conditions on the Mixing Process in Rotary Drums: Part 1—Determination of the DEM Parameters and Calibration Process
This paper’s goal was to select methods and a calibration procedure which would lead to the determination of relevant parameters of a discrete element method (DEM) and virtual material creation. Seven particulates were selected with respect to their shape (spherical and non-spherical), size and density. The first calibration experiment involved “packing test” to determine the shape accuracy and bulk density of virtual packed particulates. The series of simulations were compared with real experiments, and the size, shape and density of virtual particles were optimized. Using three apparatuses, the input parameter values were experimentally determined for a contact model that defines the behavior of particulates in DEM simulations. The research part of the paper examines the influence of factors such as particle number; pile formation method; and the method of evaluation of the angle of repose on the process of the calibration of virtual material. The most reproducible results were achieved by the “pilling” method and by the rotating drum—both evaluated by the geometric method. However, it is always advisable to make an overall visual comparison of the slope shape between the calibration simulation and the experimental curves. The bowl’s diameter to particle size ratio should be greater than 25, and the calibration experiment should contain approximately 4000 particles to ensure representative results during angle of repose calibration experiment.
Open AccessDEM Investigation of the Influence of Particulate Properties and Operating Conditions on the Mixing Process in Rotary Drums: Part 1—Determination of the DEM Parameters and Calibration Process
This paper’s goal was to select methods and a calibration procedure which would lead to the determination of relevant parameters of a discrete element method (DEM) and virtual material creation. Seven particulates were selected with respect to their shape (spherical and non-spherical), size and density. The first calibration experiment involved “packing test” to determine the shape accuracy and bulk density of virtual packed particulates. The series of simulations were compared with real experiments, and the size, shape and density of virtual particles were optimized. Using three apparatuses, the input parameter values were experimentally determined for a contact model that defines the behavior of particulates in DEM simulations. The research part of the paper examines the influence of factors such as particle number; pile formation method; and the method of evaluation of the angle of repose on the process of the calibration of virtual material. The most reproducible results were achieved by the “pilling” method and by the rotating drum—both evaluated by the geometric method. However, it is always advisable to make an overall visual comparison of the slope shape between the calibration simulation and the experimental curves. The bowl’s diameter to particle size ratio should be greater than 25, and the calibration experiment should contain approximately 4000 particles to ensure representative results during angle of repose calibration experiment.
- Open Access
DEM Investigation of the Influence of Particulate Properties and Operating Conditions on the Mixing Process in Rotary Drums: Part 2—Process Validation and Experimental Study
The process of homogenization of particulates is an indispensable part of many industrial processes, and, therefore, it is necessary to pay a special attention to this area and develop it. This paper deals with a complex study of homogenization of particulate matters in a rotary drum in terms of shape, size, and density of particles. In addition, the influence of operating parameters, such as drum filling capacity, rotational speed, and drum filling pattern are also investigated. Studies of reproducibility of discrete element method simulations, effects of rotary drum sizes or effects of drum volumetric filling to the mixture homogeneity index were also carried out. In general, the least satisfactory values of the homogeneity index resulted from the mixing of particles with different densities. The dominating factor of homogenization was the drum filling-up degree. The course of the homogeneity index in 140, 280, and 420 mm drums was very similar and after five revolutions of the drum, identical values of the homogeneity index were achieved for all the drum diameters. The optimal drum filling-up degree is at 40–50% for the spherical particles and 30–40% for the sharp-edged particles. The repeatability of simulations showed the maximum relative standard deviation of the homogeneity index at 0.6% from ten simulation repetitions with the same parametric conditions.
Open AccessDEM Investigation of the Influence of Particulate Properties and Operating Conditions on the Mixing Process in Rotary Drums: Part 2—Process Validation and Experimental Study
The process of homogenization of particulates is an indispensable part of many industrial processes, and, therefore, it is necessary to pay a special attention to this area and develop it. This paper deals with a complex study of homogenization of particulate matters in a rotary drum in terms of shape, size, and density of particles. In addition, the influence of operating parameters, such as drum filling capacity, rotational speed, and drum filling pattern are also investigated. Studies of reproducibility of discrete element method simulations, effects of rotary drum sizes or effects of drum volumetric filling to the mixture homogeneity index were also carried out. In general, the least satisfactory values of the homogeneity index resulted from the mixing of particles with different densities. The dominating factor of homogenization was the drum filling-up degree. The course of the homogeneity index in 140, 280, and 420 mm drums was very similar and after five revolutions of the drum, identical values of the homogeneity index were achieved for all the drum diameters. The optimal drum filling-up degree is at 40–50% for the spherical particles and 30–40% for the sharp-edged particles. The repeatability of simulations showed the maximum relative standard deviation of the homogeneity index at 0.6% from ten simulation repetitions with the same parametric conditions.
- Open Access
Discrete Element Method Model Optimization of Cylindrical Pellet Size
The DEM (Discrete Element Method) is one option for studying the kinematic behaviour of cylindrical pellets. The DEM experiments attempted to optimize the numerical model parameters that affected time and velocity as a cylindrical vessel emptied. This vessel was filled with cylindrical pellets. Optimization was accomplished by changing the coefficient of friction between particles and selecting the length accuracy grade of the sample cylindrical pellets. The initial state was a series of ten vessel-discharge experiments evaluated using PIV (Particle Image Velocimetry). The cylindrical pellet test samples were described according to their length in three accuracy grades. These cylindrical pellet length accuracy grades were subsequently used in the DEM simulations. The article discusses a comparison of the influence of the length accuracy grade of cylindrical pellets on optimal calibration of time and velocity when the cylindrical vessel is emptied. The accuracy grade of cylindrical pellet length in the DEM sample plays a significant role in relation to the complexity of a created simulation.
Open AccessDiscrete Element Method Model Optimization of Cylindrical Pellet Size
The DEM (Discrete Element Method) is one option for studying the kinematic behaviour of cylindrical pellets. The DEM experiments attempted to optimize the numerical model parameters that affected time and velocity as a cylindrical vessel emptied. This vessel was filled with cylindrical pellets. Optimization was accomplished by changing the coefficient of friction between particles and selecting the length accuracy grade of the sample cylindrical pellets. The initial state was a series of ten vessel-discharge experiments evaluated using PIV (Particle Image Velocimetry). The cylindrical pellet test samples were described according to their length in three accuracy grades. These cylindrical pellet length accuracy grades were subsequently used in the DEM simulations. The article discusses a comparison of the influence of the length accuracy grade of cylindrical pellets on optimal calibration of time and velocity when the cylindrical vessel is emptied. The accuracy grade of cylindrical pellet length in the DEM sample plays a significant role in relation to the complexity of a created simulation.
- Open Access
Analysis and Optimization of Material Flow inside the System of Rotary Coolers and Intake Pipeline via Discrete Element Method Modelling
There is hardly any industry that does not use transport, storage, and processing of particulate solids in its production process. In the past, all device designs were based on empirical relationships or the designer’s experience. In the field of particulate solids, however, the discrete element method (DEM) has been increasingly used in recent years. This study shows how this simulation tool can be used in practice. More specifically, in dealing with operating problems with a rotary cooler which ensures the transport and cooling of the hot fly ash generated by combustion in fluidized bed boilers. For the given operating conditions, an analysis of the current cooling design was carried out, consisting of a non-standard intake pipeline, which divides and supplies the material to two rotary coolers. The study revealed shortcomings in both the pipeline design and the cooler design. The material was unevenly dispensed between the two coolers, which combined with the limited transport capacity of the coolers, led to overflowing and congestion of the whole system. Therefore, after visualization of the material flow and export of the necessary data using DEM design measures to mitigate these unwanted phenomena were carried out.
Open AccessAnalysis and Optimization of Material Flow inside the System of Rotary Coolers and Intake Pipeline via Discrete Element Method Modelling
There is hardly any industry that does not use transport, storage, and processing of particulate solids in its production process. In the past, all device designs were based on empirical relationships or the designer’s experience. In the field of particulate solids, however, the discrete element method (DEM) has been increasingly used in recent years. This study shows how this simulation tool can be used in practice. More specifically, in dealing with operating problems with a rotary cooler which ensures the transport and cooling of the hot fly ash generated by combustion in fluidized bed boilers. For the given operating conditions, an analysis of the current cooling design was carried out, consisting of a non-standard intake pipeline, which divides and supplies the material to two rotary coolers. The study revealed shortcomings in both the pipeline design and the cooler design. The material was unevenly dispensed between the two coolers, which combined with the limited transport capacity of the coolers, led to overflowing and congestion of the whole system. Therefore, after visualization of the material flow and export of the necessary data using DEM design measures to mitigate these unwanted phenomena were carried out.
- 11 July 2018
- Published by Wiley in Chemical Engineering & Technology
- Vol. 41 (8) , 1559-1565
Monitoring of the Discharge Process of Bulk Material in Silos Using Electrical Capacitance Tomography
Monitoring the bulk material discharge from silos using electrical capacitance tomography (ECT) is an effective way to supervise dynamic flow profiles within silos. In this case, bulk materials such as wheat and corn are used. These materials are typical crops in the agricultural industry. The basic differences of these materials are shape and size. The material properties are the main factors influencing the optimal discharge processes. The ECT method is used to determine the flow profile during the discharge of each material from the silo. ECT is a non‐destructive and contactless method for measuring the inner space of the silo. The results demonstrate that the monitoring of discharge processes from the silo by applying ECT is an innovative online monitoring method with a wide application.
- 11 July 2018
- Published by Wiley in Chemical Engineering & Technology
- Vol. 41 (8) , 1559-1565
Monitoring of the Discharge Process of Bulk Material in Silos Using Electrical Capacitance Tomography
Monitoring the bulk material discharge from silos using electrical capacitance tomography (ECT) is an effective way to supervise dynamic flow profiles within silos. In this case, bulk materials such as wheat and corn are used. These materials are typical crops in the agricultural industry. The basic differences of these materials are shape and size. The material properties are the main factors influencing the optimal discharge processes. The ECT method is used to determine the flow profile during the discharge of each material from the silo. ECT is a non‐destructive and contactless method for measuring the inner space of the silo. The results demonstrate that the monitoring of discharge processes from the silo by applying ECT is an innovative online monitoring method with a wide application.
- 1 July 2018
- Published by Elsevier in Chemical Engineering Research and Design
- Vol. 135, 222-233
Experimental determination of particle–particle restitution coefficient via double pendulum method
- 1 July 2018
- Published by Elsevier in Chemical Engineering Research and Design
- Vol. 135, 222-233
Experimental determination of particle–particle restitution coefficient via double pendulum method