Quazi Md. Zobaer Shah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Quazi Md. Zobaer Shah has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Arefin Kowser
6 shared publicationsMohammad Asaduzzaman Chowdhury
4 shared publications- Mohammad Asaduzzaman Chowdhury
Dhaka University of Engineering and Technology
4 shared publications - Arefin Kowser
Department of Mechanical Engineering, Dhaka University of Engineering and Technology (DUET), Gazipur 1707, Bangladesh
2 shared publications Debashis Datta
1 shared publication- Dipayan Sikder
Nuclear Safety Division, Bangladesh Atomic Energy Regulatory Authority, Bangladesh
1 shared publication
Latest Publications
- Open Access
- 31 August 2026
- Published by MDPI AG in Preprints.org
Thermal-Hydraulic Transient and Containment Response Analysis of a VVER-1200 Reactor Under Beyond-Design-Basis ATWS Concurrent with Dual LBLOCA and Station Blackout
Background: An Anticipated Transient Without Scram (ATWS) represents one of the most severe conditions in nuclear reactor operations, escalating any concurrent malfunction into a Beyond Design Basis Accident (BDBA). When coupled with dual Large-Break Loss of Coolant Accidents (LBLOCA), station blackout, and initial fuel failure, the thermal-hydraulic stability and containment integrity of the reactor are severely compromised. Materials and Methods: In this study, the transient behavior and safety response of a Russian Gen-III+ VVER-1200 reactor were simulated using the IAEA-recommended Personal Computer Transient Analyzer (PCTran). An unmitigated accident scenario featuring simultaneous 1000cm2 breaks in both the hot and cold legs, failure of the SCRAM mechanism, a total loss of AC power, and 5% fuel failure at power was evaluated over a 300-second simulation window. Model performance was benchmarked and validated against Final Safety Analysis Report (FSAR) core flow data. Results: The simulation demonstrates that the Departure from Nucleate Boiling Ratio (DNBR) dropped below 1.0 within 30 seconds, triggering an immediate boiling crisis due to sustained core power. Complete steam voiding across the reactor core occurred in 80 seconds. Consequently, reactor building pressure exceeded the 5-bar design threshold in only 90 seconds and reached 14.93 bar at 300 seconds, while containment temperatures peaked at 193.7 °C. Although peak fuel and cladding temperatures remained within design limits to prevent immediate core meltdown, the rapid containment over-pressurization severely restricts available operator response windows, posing a critical containment failure hazard. Conclusion: Simultaneous ATWS, dual-leg LBLOCA with fuel failure, and station blackout in a VVER-1200 induce a critical boiling crisis within 30 seconds and full core voiding in 80 seconds due to unmitigated core power. Although passive systems prevent immediate fuel and cladding meltdown, containment pressure breaches the 5-bar design threshold in just 90 seconds, highlighting that containment over-pressurization rather than core degradation is the most immediate threat requiring enhanced passive mitigation.
- 31 August 2026
- Published by MDPI AG in Preprints.org
Open AccessThermal-Hydraulic Transient and Containment Response Analysis of a VVER-1200 Reactor Under Beyond-Design-Basis ATWS Concurrent with Dual LBLOCA and Station Blackout
Background: An Anticipated Transient Without Scram (ATWS) represents one of the most severe conditions in nuclear reactor operations, escalating any concurrent malfunction into a Beyond Design Basis Accident (BDBA). When coupled with dual Large-Break Loss of Coolant Accidents (LBLOCA), station blackout, and initial fuel failure, the thermal-hydraulic stability and containment integrity of the reactor are severely compromised. Materials and Methods: In this study, the transient behavior and safety response of a Russian Gen-III+ VVER-1200 reactor were simulated using the IAEA-recommended Personal Computer Transient Analyzer (PCTran). An unmitigated accident scenario featuring simultaneous 1000cm2 breaks in both the hot and cold legs, failure of the SCRAM mechanism, a total loss of AC power, and 5% fuel failure at power was evaluated over a 300-second simulation window. Model performance was benchmarked and validated against Final Safety Analysis Report (FSAR) core flow data. Results: The simulation demonstrates that the Departure from Nucleate Boiling Ratio (DNBR) dropped below 1.0 within 30 seconds, triggering an immediate boiling crisis due to sustained core power. Complete steam voiding across the reactor core occurred in 80 seconds. Consequently, reactor building pressure exceeded the 5-bar design threshold in only 90 seconds and reached 14.93 bar at 300 seconds, while containment temperatures peaked at 193.7 °C. Although peak fuel and cladding temperatures remained within design limits to prevent immediate core meltdown, the rapid containment over-pressurization severely restricts available operator response windows, posing a critical containment failure hazard. Conclusion: Simultaneous ATWS, dual-leg LBLOCA with fuel failure, and station blackout in a VVER-1200 induce a critical boiling crisis within 30 seconds and full core voiding in 80 seconds due to unmitigated core power. Although passive systems prevent immediate fuel and cladding meltdown, containment pressure breaches the 5-bar design threshold in just 90 seconds, highlighting that containment over-pressurization rather than core degradation is the most immediate threat requiring enhanced passive mitigation.
- Open Access
- 18 June 2026
- Published by Wiley in Bioengineering & Translational Medicine
- Vol. 11 (5)
Mechanical‐medical convergence in heart failure: Artificial intelligence, finite‐element modeling, and 3D printing for diagnosis and prognosis
Heart failure remains a leading cause of global morbidity and mortality, yet routine clinical indices often miss the regional biomechanical disturbances that drive progression and shape treatment response. This State‐of‐the‐Art review examines how finite‐element (FE) modeling, additive manufacturing, and artificial intelligence (AI) are converging to improve the diagnosis, phenotyping, procedural planning, and prognostic assessment of heart failure (HF). Although these technologies have matured in structural heart disease and transcatheter intervention research, their greatest translational potential may lie in HF, where patient‐specific ventricular remodeling, myocardial stress–strain heterogeneity, valve‐ventricular coupling, and device‐tissue interaction are incompletely captured by conventional clinical indices. We synthesize translational and clinical literature published from 2015 to 2026 on imaging‐derived FE models, multimaterial 3D‐printed cardiovascular phantoms, and AI‐based analytic pipelines relevant to HF populations or HF‐related decision pathways. FE approaches provide mechanistic estimates of regional myocardial deformation, wall stress, and remodeling trajectories; 3D‐printed phantoms enable bench‐top validation, device rehearsal, and hemodynamic replication; and AI supports segmentation, phenotyping, multimodal integration, and risk prediction. Across all three domains, however, the evidence base remains dominated by retrospective studies, bench validation, and small translational cohorts, with limited prospective outcome validation and inconsistent reporting of reproducibility. We therefore propose an evidence‐aware, HF‐centered framework for integrating computational mechanics, physical phantoms, and data‐driven models into digital‐physical twin workflows. From a clinical perspective, the near‐term opportunity is not autonomous decision‐making, but better mechanistic phenotyping, more transparent procedural planning, and more rigorous testing of patient‐specific hypotheses before intervention. Standardized reporting, external validation, careful materials characterization, and multicenter endpoint‐linked studies will be essential for clinical translation.
- 18 June 2026
- Published by Wiley in Bioengineering & Translational Medicine
- Vol. 11 (5)
Open AccessMechanical‐medical convergence in heart failure: Artificial intelligence, finite‐element modeling, and 3D printing for diagnosis and prognosis
Heart failure remains a leading cause of global morbidity and mortality, yet routine clinical indices often miss the regional biomechanical disturbances that drive progression and shape treatment response. This State‐of‐the‐Art review examines how finite‐element (FE) modeling, additive manufacturing, and artificial intelligence (AI) are converging to improve the diagnosis, phenotyping, procedural planning, and prognostic assessment of heart failure (HF). Although these technologies have matured in structural heart disease and transcatheter intervention research, their greatest translational potential may lie in HF, where patient‐specific ventricular remodeling, myocardial stress–strain heterogeneity, valve‐ventricular coupling, and device‐tissue interaction are incompletely captured by conventional clinical indices. We synthesize translational and clinical literature published from 2015 to 2026 on imaging‐derived FE models, multimaterial 3D‐printed cardiovascular phantoms, and AI‐based analytic pipelines relevant to HF populations or HF‐related decision pathways. FE approaches provide mechanistic estimates of regional myocardial deformation, wall stress, and remodeling trajectories; 3D‐printed phantoms enable bench‐top validation, device rehearsal, and hemodynamic replication; and AI supports segmentation, phenotyping, multimodal integration, and risk prediction. Across all three domains, however, the evidence base remains dominated by retrospective studies, bench validation, and small translational cohorts, with limited prospective outcome validation and inconsistent reporting of reproducibility. We therefore propose an evidence‐aware, HF‐centered framework for integrating computational mechanics, physical phantoms, and data‐driven models into digital‐physical twin workflows. From a clinical perspective, the near‐term opportunity is not autonomous decision‐making, but better mechanistic phenotyping, more transparent procedural planning, and more rigorous testing of patient‐specific hypotheses before intervention. Standardized reporting, external validation, careful materials characterization, and multicenter endpoint‐linked studies will be essential for clinical translation.
- Open Access
- 17 January 2022
- Published by MDPI AG in Journal of Composites Science
- Vol. 6 (1) , 31
Modeling Fracture Formation, Behavior and Mechanics of Polymeric Materials: A Biomedical Implant Perspective
In industrial applications where contact behavior of materials is characterized, fretting-associated fatigue plays a vital role as a failure agitator. While considering connection, it encounters friction. Biomaterials like polytetrafluoroethylene (PTFE) and ultra-high-molecular-weight polyethylene (UHMWPE) are renowned for their low coefficient of friction and are utilized in sophisticated functions like the hip joint cup and other biomedical implants. In addition to the axial stresses, some degree of dynamic bending stress is also developed occasionally in those fretting contacts. This research investigated the fracture behavior of a polymer PTFE under bending fretting fatigue. Finite element analysis justified the experimental results. A mathematical model is proposed by developing an empirical equation for fracture characterization in polymers like PTFE. It was found that the bending stiffness exists below the loading point ratio (LPR) 3.0, near the collar section of the specimen. Along with fretting, the bending load forces the specimen to crack in a brittle-ductile mode near the sharp-edged collar where the maximum strain rate, as well as stress, builds up. For a loading point ratio of above 3, a fracture takes place near the fretting pads in a tensile-brittle mode. Strain proportionality factor, k was found as a life optimization parameter under conditional loading. The microscopic analysis revealed that the fracture striation initiates perpendicularly to the fretting load. The fretting fatigue damage characteristic of PTFE may have a new era for the biomedical application of polymer-based composite materials.
- 17 January 2022
- Published by MDPI AG in Journal of Composites Science
- Vol. 6 (1) , 31
Open AccessModeling Fracture Formation, Behavior and Mechanics of Polymeric Materials: A Biomedical Implant Perspective
In industrial applications where contact behavior of materials is characterized, fretting-associated fatigue plays a vital role as a failure agitator. While considering connection, it encounters friction. Biomaterials like polytetrafluoroethylene (PTFE) and ultra-high-molecular-weight polyethylene (UHMWPE) are renowned for their low coefficient of friction and are utilized in sophisticated functions like the hip joint cup and other biomedical implants. In addition to the axial stresses, some degree of dynamic bending stress is also developed occasionally in those fretting contacts. This research investigated the fracture behavior of a polymer PTFE under bending fretting fatigue. Finite element analysis justified the experimental results. A mathematical model is proposed by developing an empirical equation for fracture characterization in polymers like PTFE. It was found that the bending stiffness exists below the loading point ratio (LPR) 3.0, near the collar section of the specimen. Along with fretting, the bending load forces the specimen to crack in a brittle-ductile mode near the sharp-edged collar where the maximum strain rate, as well as stress, builds up. For a loading point ratio of above 3, a fracture takes place near the fretting pads in a tensile-brittle mode. Strain proportionality factor, k was found as a life optimization parameter under conditional loading. The microscopic analysis revealed that the fracture striation initiates perpendicularly to the fretting load. The fretting fatigue damage characteristic of PTFE may have a new era for the biomedical application of polymer-based composite materials.
- Open Access
Fretting & friction induced fatigue failure: damage criterion of polytetrafluoroethylene
- Open Access
- 1 January 2020
- Published by National Library of Serbia in Theoretical and Applied Mechanics
- Vol. 47 (1) , 113-122
Investigation of the combined effect of notch and fretting on bending fatigue
Being a common phenomenon in failure mechanism, fretting fatigue has emerged as one of the major concerns in recent years both in research and industrial applications. In the present study, the effect of notch and fretting on bending fatigue has been examined by FEM analysis. Based on the available and validated FEM model, analyses have been carried out on single point fretting with a double notch and double point fretting with a single notch respectively. Along the predefined paths through the edge, thickness and notch, fatigue behavior and stress-strain distribution have been studied. It has been found that stress and strain distribution is uniformly spaced for constant fretting loads with a variable concentric load whereas variable fretting loads yield almost two times results. Stress and strain singularity is found for transverse loading when highly stressed. Peak stress was found on the stress distribution path for fretting action for the combined fretting and notch presence. Fatigue life was influenced more drastically by variable fretting loads than variable concentric loadings only in case of tension. Dual action of fretting with notches was found more detrimental than the single action of double fretting/notching.
- 1 January 2020
- Published by National Library of Serbia in Theoretical and Applied Mechanics
- Vol. 47 (1) , 113-122
Open AccessInvestigation of the combined effect of notch and fretting on bending fatigue
Being a common phenomenon in failure mechanism, fretting fatigue has emerged as one of the major concerns in recent years both in research and industrial applications. In the present study, the effect of notch and fretting on bending fatigue has been examined by FEM analysis. Based on the available and validated FEM model, analyses have been carried out on single point fretting with a double notch and double point fretting with a single notch respectively. Along the predefined paths through the edge, thickness and notch, fatigue behavior and stress-strain distribution have been studied. It has been found that stress and strain distribution is uniformly spaced for constant fretting loads with a variable concentric load whereas variable fretting loads yield almost two times results. Stress and strain singularity is found for transverse loading when highly stressed. Peak stress was found on the stress distribution path for fretting action for the combined fretting and notch presence. Fatigue life was influenced more drastically by variable fretting loads than variable concentric loadings only in case of tension. Dual action of fretting with notches was found more detrimental than the single action of double fretting/notching.
- 18 December 2019
- Published by Taylor & Francis in Australian Journal of Mechanical Engineering
- Vol. 20 (1) , 263-275
A parametric investigation on the fretting fatigue behaviour of heat treated Al 6061-T6 under rotating bending phenomena
This research investigated the effect of variable fretting parameters on bending fatigue behaviour of heat-treated Al-Mg-Si alloy (Al 6061-T6). Bulk stress, contact pressure, pad geometry, and locations were chosen as variable parameters to measure its consequence on fatigue life. A developed FEM model justified the experimental observation. It observed that, within the lower bulk stress range, fretting action decreases the fatigue life of Aluminium alloy significantly than the plain one. However, this difference almost vanishes at higher-order loading as well as stress in comparison to plain fatigue. Contact pressure and stress distribution along the contact path and non-filleted-edge suggest about the importance of safety design over the fretting zones. The flat on cylinder contacts was found as detrimental at higher-order contact pressure while cylinder on cylinder one reduces notably at low contact pressure. Fuzzy logic, a soft computing technique was implemented to predict the fretting fatigue as well as the effect of pad location from surface graphs. Nevertheless, catastrophic rupture followed the aspect of fretting loading parameter that showed fretting not only affects in quantity but also the quality of the fatigue behaviour of Al 6061-T6.
- 18 December 2019
- Published by Taylor & Francis in Australian Journal of Mechanical Engineering
- Vol. 20 (1) , 263-275
A parametric investigation on the fretting fatigue behaviour of heat treated Al 6061-T6 under rotating bending phenomena
This research investigated the effect of variable fretting parameters on bending fatigue behaviour of heat-treated Al-Mg-Si alloy (Al 6061-T6). Bulk stress, contact pressure, pad geometry, and locations were chosen as variable parameters to measure its consequence on fatigue life. A developed FEM model justified the experimental observation. It observed that, within the lower bulk stress range, fretting action decreases the fatigue life of Aluminium alloy significantly than the plain one. However, this difference almost vanishes at higher-order loading as well as stress in comparison to plain fatigue. Contact pressure and stress distribution along the contact path and non-filleted-edge suggest about the importance of safety design over the fretting zones. The flat on cylinder contacts was found as detrimental at higher-order contact pressure while cylinder on cylinder one reduces notably at low contact pressure. Fuzzy logic, a soft computing technique was implemented to predict the fretting fatigue as well as the effect of pad location from surface graphs. Nevertheless, catastrophic rupture followed the aspect of fretting loading parameter that showed fretting not only affects in quantity but also the quality of the fatigue behaviour of Al 6061-T6.
- Open Access
- 21 August 2019
- Published by Springer Nature in SN Applied Sciences
- Vol. 1 (9) , 1067
On the diversity in design for different bending fretting fatigue mechanism
- 21 August 2019
- Published by Springer Nature in SN Applied Sciences
- Vol. 1 (9) , 1067
Open AccessOn the diversity in design for different bending fretting fatigue mechanism
- 25 January 2019
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 19 (1) , 245-249
Failure Mechanism of Polytetrafluoroethylene Under Friction Fatigue
- 25 January 2019
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 19 (1) , 245-249
Failure Mechanism of Polytetrafluoroethylene Under Friction Fatigue
- Open Access
- 10 February 2017
- Published by SAGE Publications in International Journal of Damage Mechanics
- Vol. 27 (4) , 453-487
Characteristics and damage mechanisms of bending fretting fatigue of materials
Fretting fatigue has attracted substantial research interest in recent decades owing to its relevance in a wide range of applications. This paper reviews previous studies and describes ongoing research. Particularly, only a few studies on bending fretting fatigue have been conducted. This review paper emphasizes the effect of bending fretting fatigue of different materials under different operating parameters. In addition, the damage mechanisms with respect to nature of failure of materials are also discussed. This paper can be used as a reference for design and development of modern technologies and selection of appropriate material in industries.
- 10 February 2017
- Published by SAGE Publications in International Journal of Damage Mechanics
- Vol. 27 (4) , 453-487
Open AccessCharacteristics and damage mechanisms of bending fretting fatigue of materials
Fretting fatigue has attracted substantial research interest in recent decades owing to its relevance in a wide range of applications. This paper reviews previous studies and describes ongoing research. Particularly, only a few studies on bending fretting fatigue have been conducted. This review paper emphasizes the effect of bending fretting fatigue of different materials under different operating parameters. In addition, the damage mechanisms with respect to nature of failure of materials are also discussed. This paper can be used as a reference for design and development of modern technologies and selection of appropriate material in industries.