Qian Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Qian Zhao has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Linbing Wang
School of Environmental, Civil, Agricultural and Mechanical Engineering, University of Georgia, Athens, GA 30602, USA
3 shared publications - Hailu Yang
National Center for Materials Service Safety, University of Science and Technology Beijing, Beijing 100083, China
2 shared publications - Pengfei Liu
Institute of Highway Engineering, RWTH Aachen University
2 shared publications - Dawei Wang
School of Transportation Science and Engineering, Harbin Institute of Technology, Harbin, People’s Republic of China
1 shared publication - Jie Xu
School of Civil Engineering, Tianjin University, Tianjin 300350, China
1 shared publication - Markus Oeser
Federal Highway and Transport Research Institute, Bergisch Gladbach, Germany
1 shared publication
Latest Publications
- Open Access
Vehicle Load Information Acquisition Using Roadside Micro-Electromechanical Systems Accelerometers
Vehicle load is crucial for road design, maintenance, and expansion, while vehicle speed and lateral position are essential for traffic management and driving safety. This paper introduces a method for collecting vehicle speed, lateral position, and load information using roadside Micro-Electromechanical Systems (MEMS) accelerometers located on the pavement. Firstly, this research analyzes the distribution of pavement vibration responses in both lateral and vertical directions based on the Finite Element Method (FEM) data provided in the literature. Then, pavement vibration data is collected by roadside sensors with a Full-scale Accelerated Loading Tester, considering varying vehicle speeds, loads, and lateral positions. The results reveal that the vertical peak acceleration increases linearly with vehicle speed within a range of 5–22 km/h, decreases following a power law as the lateral distance between the wheel center and sensor increases from 0.4 to 0.9 m, which is consistent with the trends observed in the literature’s FEM data. The vibration energy of the vertical acceleration exhibits a positive linear correlation with the total vehicle load, with a correlation coefficient of 0.885. This approach offers a practical method for vehicle load estimation, optimal sensor deployment, and enhancement of pavement performance monitoring systems.
Open AccessVehicle Load Information Acquisition Using Roadside Micro-Electromechanical Systems Accelerometers
Vehicle load is crucial for road design, maintenance, and expansion, while vehicle speed and lateral position are essential for traffic management and driving safety. This paper introduces a method for collecting vehicle speed, lateral position, and load information using roadside Micro-Electromechanical Systems (MEMS) accelerometers located on the pavement. Firstly, this research analyzes the distribution of pavement vibration responses in both lateral and vertical directions based on the Finite Element Method (FEM) data provided in the literature. Then, pavement vibration data is collected by roadside sensors with a Full-scale Accelerated Loading Tester, considering varying vehicle speeds, loads, and lateral positions. The results reveal that the vertical peak acceleration increases linearly with vehicle speed within a range of 5–22 km/h, decreases following a power law as the lateral distance between the wheel center and sensor increases from 0.4 to 0.9 m, which is consistent with the trends observed in the literature’s FEM data. The vibration energy of the vertical acceleration exhibits a positive linear correlation with the total vehicle load, with a correlation coefficient of 0.885. This approach offers a practical method for vehicle load estimation, optimal sensor deployment, and enhancement of pavement performance monitoring systems.
- Open Access
- 7 December 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (24) , 13522
Characterizing the Economic and Environmental Benefits of LNG Heavy-Duty Trucks: A Case Study in Shenzhen, China
Heavy-duty trucks (HDTs) in road freight are a primary contributor of PM2.5 and NOX emissions in many cities. Shenzhen, a megacity of China, has already made great efforts to promote the green transport transition, including via the Liquefied Natural Gas (LNG) HDTs program, which may be the largest alternative fuel vehicle promotion program in the world. In order to fully understand the actual efficiency of such program, the economic and environmental impacts of LNG HDTs were analyzed in this study. The results revealed that, while the capital cost of LNG HDTs is higher than that of diesel HDTs, the aggregated cost during the entire operation period of LNG HDTs is 10% to 17% lower than that of diesel HDTs. By replacing existing diesel HDTs mode (including China-I to China-V) with LNG HDTs (100%), environmental impact analysis showed that PM2.5 and NOX emissions could be reduced by 96.7% and 73.2% in the city level, respectively. Moreover, the environmental benefits of using purely LNG HDTs versus just China-V diesel HDTs were also compared, which indicated that LNG substitution is superior to China-V, with a reduction of 20.9% for PM2.5 and 35.4% for NOX, respectively. Overall, the effectiveness of the promotion of LNG HDTs is notable in Shenzhen, and these findings could provide references for other cities to promote LNG HDTs and beyond.
- 7 December 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (24) , 13522
Open AccessCharacterizing the Economic and Environmental Benefits of LNG Heavy-Duty Trucks: A Case Study in Shenzhen, China
Heavy-duty trucks (HDTs) in road freight are a primary contributor of PM2.5 and NOX emissions in many cities. Shenzhen, a megacity of China, has already made great efforts to promote the green transport transition, including via the Liquefied Natural Gas (LNG) HDTs program, which may be the largest alternative fuel vehicle promotion program in the world. In order to fully understand the actual efficiency of such program, the economic and environmental impacts of LNG HDTs were analyzed in this study. The results revealed that, while the capital cost of LNG HDTs is higher than that of diesel HDTs, the aggregated cost during the entire operation period of LNG HDTs is 10% to 17% lower than that of diesel HDTs. By replacing existing diesel HDTs mode (including China-I to China-V) with LNG HDTs (100%), environmental impact analysis showed that PM2.5 and NOX emissions could be reduced by 96.7% and 73.2% in the city level, respectively. Moreover, the environmental benefits of using purely LNG HDTs versus just China-V diesel HDTs were also compared, which indicated that LNG substitution is superior to China-V, with a reduction of 20.9% for PM2.5 and 35.4% for NOX, respectively. Overall, the effectiveness of the promotion of LNG HDTs is notable in Shenzhen, and these findings could provide references for other cities to promote LNG HDTs and beyond.
- Open Access
Numerical Analysis of Signal Response Characteristic of Piezoelectric Energy Harvesters Embedded in Pavement
Piezoelectric pavement energy harvesting is a technological approach to transform mechanical energy into electrical energy. When a piezoelectric energy harvester (PEH) is embedded in asphalt pavements or concrete pavements, it is subjected to traffic loads and generates electricity. The wander of the tire load and the positioning of the PEH affect the power generation; however, they were seldom comprehensively investigated until now. In this paper, a numerical study on the influence of embedding depth of the PEH and the horizontal distance between a tire load and the PEH on piezoelectric power generation is presented. The result shows that the relative position between the PEH and the load influences the voltage magnitude, and different modes of stress state change voltage polarity. Two mathematic correlations between the embedding depth, the horizontal distance, and the generated voltage were fitted based on the computational results. This study can be used to estimate the power generation efficiency, and thus offer basic information for further development to improve the practical design of PEHs in an asphalt pavement.
Open AccessNumerical Analysis of Signal Response Characteristic of Piezoelectric Energy Harvesters Embedded in Pavement
Piezoelectric pavement energy harvesting is a technological approach to transform mechanical energy into electrical energy. When a piezoelectric energy harvester (PEH) is embedded in asphalt pavements or concrete pavements, it is subjected to traffic loads and generates electricity. The wander of the tire load and the positioning of the PEH affect the power generation; however, they were seldom comprehensively investigated until now. In this paper, a numerical study on the influence of embedding depth of the PEH and the horizontal distance between a tire load and the PEH on piezoelectric power generation is presented. The result shows that the relative position between the PEH and the load influences the voltage magnitude, and different modes of stress state change voltage polarity. Two mathematic correlations between the embedding depth, the horizontal distance, and the generated voltage were fitted based on the computational results. This study can be used to estimate the power generation efficiency, and thus offer basic information for further development to improve the practical design of PEHs in an asphalt pavement.
- 1 March 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 31 (3)
Numerical Study on Influence of Piezoelectric Energy Harvester on Asphalt Pavement Structural Responses
In recent years, energy harvesting technologies have been applied in pavement engineering. Piezoelectric energy harvesting in pavement aims to take advantage of the vehicle load on a road. Most of the existing theoretical and experimental research focused on the materials, structures, and shape of the energy harvesters to improve the efficiency of the output energy. However, few investigations have analyzed the compatibility of piezoelectric energy harvesters (PEHs) and pavement. This study investigated the influence of PEHs on the structural response of asphalt pavement. Three-dimensional (3D) tire–pavement interaction finite-element models with and without a PEH were constructed according to a previous demonstration project. Several critical points within the pavement structures were selected and their mechanical responses induced by the passing tire were compared and discussed. A parametric study analyzed the pavement responses to different traffic speeds, tire loads, and bonding conditions between the PEHs and asphalt layers. Two potential optimization solutions for the PEH were explored. The results showed that the influence of the PEH on the asphalt pavement performance is significant in terms of the horizontal and vertical strains and von Mises stresses. A PEH causes potential permanent damage initiation in its adjacent area within the pavement structure. The maximum values of the horizontal tensile strains appeared at the bottom of the asphalt surface course in all pavement models with a PEH. These conclusions offer basic information for improving the practical design of PEHs in asphalt pavement.
- 1 March 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 31 (3)
Numerical Study on Influence of Piezoelectric Energy Harvester on Asphalt Pavement Structural Responses
In recent years, energy harvesting technologies have been applied in pavement engineering. Piezoelectric energy harvesting in pavement aims to take advantage of the vehicle load on a road. Most of the existing theoretical and experimental research focused on the materials, structures, and shape of the energy harvesters to improve the efficiency of the output energy. However, few investigations have analyzed the compatibility of piezoelectric energy harvesters (PEHs) and pavement. This study investigated the influence of PEHs on the structural response of asphalt pavement. Three-dimensional (3D) tire–pavement interaction finite-element models with and without a PEH were constructed according to a previous demonstration project. Several critical points within the pavement structures were selected and their mechanical responses induced by the passing tire were compared and discussed. A parametric study analyzed the pavement responses to different traffic speeds, tire loads, and bonding conditions between the PEHs and asphalt layers. Two potential optimization solutions for the PEH were explored. The results showed that the influence of the PEH on the asphalt pavement performance is significant in terms of the horizontal and vertical strains and von Mises stresses. A PEH causes potential permanent damage initiation in its adjacent area within the pavement structure. The maximum values of the horizontal tensile strains appeared at the bottom of the asphalt surface course in all pavement models with a PEH. These conclusions offer basic information for improving the practical design of PEHs in asphalt pavement.
- 10 June 2017
- Published by Springer Nature in Frontiers of Structural and Civil Engineering
- Vol. 12 (2) , 201-206
A dimensional analysis on asphalt binder fracture and fatigue cracking
- 10 June 2017
- Published by Springer Nature in Frontiers of Structural and Civil Engineering
- Vol. 12 (2) , 201-206
A dimensional analysis on asphalt binder fracture and fatigue cracking