Tomas Stankevic
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Tomas Stankevic has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Anatoly Shabalin
Deutsches Elektronen-Synchrotron DESY 2 , Notkestrasse 85, D-22607 Hamburg, Germany
1 shared publicationAnders Mikkelsen
Lund University 4 NanoLund, Department of Physics P.O. Box 118, 22 100 Lund, Sweden
1 shared publicationDmitry Dzhigaev
Deutsches Elektronen-Synchrotron DESY 2 , Notkestrasse 85, D-22607 Hamburg, Germany
1 shared publicationGerald Falkenberg
Deutsches Elektronen-Synchrotron DESY 2 , Notkestrasse 85, D-22607 Hamburg, Germany
1 shared publicationIvan A. Vartanyants
Deutsches Elektronen-Synchrotron DESY 2 , Notkestrasse 85, D-22607 Hamburg, Germany
1 shared publicationJuliane Reinhardt
Deutsches Elektronen-Synchrotron DESY 2 , Notkestrasse 85, D-22607 Hamburg, Germany
1 shared publication
Latest Publications
- 7 September 2015
- Published by AIP Publishing in Applied Physics Letters
- Vol. 107 (10) , 103101
Strain mapping in an InGaN/GaN nanowire using a nano-focused x-ray beam
Strained InGaN/GaN core-shell nanowires (NWs) are promising candidates for solid state lighting applications due to their superior properties compared to planar films. NW based devices consist of multiple functional layers, which sum up to many hundred nanometers in thickness, that can uniquely be accessed in a non-destructive fashion by hard X-rays. Here, we present a detailed nanoscale strain mapping performed on a single, 400 nm thick and 2 μm long core-shell InGaN/GaN nanowire with an x-ray beam focused down to 100 nm. We observe an inhomogeneous strain distribution caused by the asymmetric strain relaxation in the shell. One side of the InGaN shell was fully strained, whereas the other side and the top part were relaxed. Additionally, tilt and strain gradients were determined at the interface with the substrate.
- 7 September 2015
- Published by AIP Publishing in Applied Physics Letters
- Vol. 107 (10) , 103101
Strain mapping in an InGaN/GaN nanowire using a nano-focused x-ray beam
Strained InGaN/GaN core-shell nanowires (NWs) are promising candidates for solid state lighting applications due to their superior properties compared to planar films. NW based devices consist of multiple functional layers, which sum up to many hundred nanometers in thickness, that can uniquely be accessed in a non-destructive fashion by hard X-rays. Here, we present a detailed nanoscale strain mapping performed on a single, 400 nm thick and 2 μm long core-shell InGaN/GaN nanowire with an x-ray beam focused down to 100 nm. We observe an inhomogeneous strain distribution caused by the asymmetric strain relaxation in the shell. One side of the InGaN shell was fully strained, whereas the other side and the top part were relaxed. Additionally, tilt and strain gradients were determined at the interface with the substrate.
- 8 March 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 41 (5) , 1520-1525
Velocity-Induced Current Profiles Inside the Rails of an Electric Launcher
Previous investigations have shown that an array of novel CMR-B-scalar sensors based on the colossal magnetoresistance effect can be used to measure the magnetic field distribution in the vicinity of the rails of a railgun. However, the data obtained suffered from electromagnetic interference. Therefore, the measurement system was considerably improved to obtain better signal quality. In this paper, the results obtained during the dynamic operation of the ISL railgun RAFIRA are presented. The magnetic field distribution in the vicinity of the rails was measured at different armature velocities. Additional information was obtained using high-speed camera snapshots. The experimental results are compared with simulations performed with the finite element code COMSOL Multiphysics. In particular, the influence of the armature current on the measurements is discussed. It is concluded that the magnetic field distribution in the vicinity of the rails clearly indicates an increased current concentration in the rear part of the armature-rail contact interface. Moreover, the current concentration depends on the speed of the armature. Velocity-dependent skin depths at the surface of aluminum (Dural) rails for projectile velocities ranging between 750 and 1500 m/s are investigated.
- 8 March 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 41 (5) , 1520-1525
Velocity-Induced Current Profiles Inside the Rails of an Electric Launcher
Previous investigations have shown that an array of novel CMR-B-scalar sensors based on the colossal magnetoresistance effect can be used to measure the magnetic field distribution in the vicinity of the rails of a railgun. However, the data obtained suffered from electromagnetic interference. Therefore, the measurement system was considerably improved to obtain better signal quality. In this paper, the results obtained during the dynamic operation of the ISL railgun RAFIRA are presented. The magnetic field distribution in the vicinity of the rails was measured at different armature velocities. Additional information was obtained using high-speed camera snapshots. The experimental results are compared with simulations performed with the finite element code COMSOL Multiphysics. In particular, the influence of the armature current on the measurements is discussed. It is concluded that the magnetic field distribution in the vicinity of the rails clearly indicates an increased current concentration in the rear part of the armature-rail contact interface. Moreover, the current concentration depends on the speed of the armature. Velocity-dependent skin depths at the surface of aluminum (Dural) rails for projectile velocities ranging between 750 and 1500 m/s are investigated.