Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Zdenek Stary has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Thermoplastic Starch Composites with Highly Exfoliated Nano-Clay Fillers and Excellent Barrier Properties

    by Veronika Gajdosova, Beata Strachota, Vaclav Pokorny, Libuse Brozova, Jan Kozisek, Ewa Pavlova, Zdenek Stary, Miroslav Slouf, Adam Strachota

    Thermoplastic starch (TPS) nanocomposites with unprecedentedly high loadings of up to 15 wt.% of the nano-clays Laponite (LAP; a synthetic product capable of good dispersion in suitable media) or Montmorillonite (MMT; modified with dialkyldimethylammonium chloride) were prepared by means of our new, two-step TPS preparation protocol. In both the TPS/LAP and TPS/MMT composites, we achieved perfect dispersion and extensive exfoliation of the nano-clays, resulting in pronounced improvements in mechanical performance (modulus increased up to one order of magnitude) and in excellent gas-barrier properties (extremely small permeabilities for O2, CO2, and even H2). MMT, owing to its larger platelet size and to the formation of partially exfoliated multi-layer structures, generated a percolating filler network that provided particularly strong reinforcement, especially at 15 wt.% loading. LAP, though more completely exfoliated, generated a somewhat smaller mechanical reinforcement, but it more strongly increased processing viscosity due to its high specific surface area, which generated highly stable physical crosslinking that persisted even at processing temperatures of T ≥ 120 °C. Efficient matrix–filler interactions were confirmed by thermogravimetric analysis, where the better-exfoliated LAP generated a higher stabilization. The combination of strong mechanical reinforcement with outstanding gas-barrier properties makes the TPS/MMT and TPS/LAP nanocomposites attractive for food-packaging applications, where their natural origin, non-toxicity, bio-degradability, and abundance of nanocomposite components are an additional bonus.


  • Open Access

    SEM, FTIR and TGA analysis of Graphitic carbon nitride (g-C3N4) and its modification as a composite material

    by Karel Klouda, Petra Roupcová, Petra Bursíková, Romana Friedrichová, Kateřina Bátrlová, Eva Kuželová Košťáková, Zdeněk Starý, Jiří Tilhon

    This paper describes the preparation of g-C3N4 by polycondensation of melamine at 511 °C and its subsequent doping with Fe2O3, Cu, GO, rGO, DA and their combinations. Graphitic carbon nitride represents an innovative material with numerous applications, particularly within the domains of catalysis and water treatment. FTIR and thermogravimetric analysis were predominantly employed for the purpose of identification, while SEM images were captured at incremental resolutions. The subsequent section of the manuscript delineates the fabrication of composite materials within polymers, including PE-foil and PP-filaments intended for 3D printing, as well as PVB into nanofibers via electrostatic spinning techniques. The objective of this study was to examine the thermal stability of nanofibers produced from PVB in conjunction with g-C3N4 composite (18-20 %) utilizing two methodologies: EL DC spinning and EL AC spinning. The material exhibiting the most efficacious synthesis will undergo further assessment to evaluate its potential utility in the photocatalytic degradation of environmental pollutants.


  • Open Access

    Impact of Acid Hydrolysis on Morphology, Rheology, Mechanical Properties, and Processing of Thermoplastic Starch

    by Saffana Kouka, Veronika Gajdosova, Beata Strachota, Ivana Sloufova, Radomir Kuzel, Zdenek Stary, Miroslav Slouf

    We modified native wheat starch using 15, 30, and 60 min of acid hydrolysis (AH). The non-modified and AH-modified starches were converted to highly homogeneous thermoplastic starches (TPSs) using our two-step preparation protocol consisting of solution casting and melt mixing. Our main objective was to verify if AH can decrease the processing temperature of TPS. All samples were characterized in detail by microscopic, spectroscopic, diffraction, thermomechanical, rheological, and micromechanical methods, including in situ measurements of torque and temperature during the final melt mixing step. The experimental results showed that (i) AH decreased the average molecular weight preferentially in the amorphous regions, (ii) the lower-viscosity matrix in the AH-treated starches resulted in slightly higher crystallinity, and (iii) all AH-modified TPSs with a less viscous amorphous phase and higher content of crystalline phase exhibited similar properties. The effect of the higher crystallinity predominated at a laboratory temperature and low deformations, resulting in slightly stiffer material. The effect of the lower viscosity dominated during the melt mixing, where the shorter molecules acted as a lubricant and decreased the in situ measured processing temperature. The AH-induced decrease in the processing temperature could be beneficial for energy savings and/or possible temperature-sensitive admixtures for TPS systems.


  • Open Access

    Graphitic Carbon Nitride (g-C3N4) and Its Modification as a Composite Material

    by Karel Klouda, Petra Roupcová, Martina Vráblová, Kamil Maciej Górecki, Petra Bursíková, Romana Friedrichová, Kateřina Bátrlová, Eva Kuželová Koštálová, Zdeněk Starý, Jiří Tilhon

    This paper describes the preparation of g-C3N4 by polycondensation of melamine at 511 °C and its subsequent doping with Fe2O3, Cu, GO, rGO, DA and their combinations. Graphitic carbon nitride is a new material with plenty of applications e.g. in the fields of catalysis or water treatment. FTIR, thermogravimetric analysis was mainly used for identification and SEM images were taken at gradual resolution. The next part of the paper describes the preparation of composite compounds in polymer, PE-foil, PP-filaments for 3D printing, in PVB into nanofibers by electrostatic spinning. The aim of this article was to investigate the thermal stability of nanofibers prepared from PVB with g-C3N4 composite (18-20 %) by two methods: EL DC spinning and EL AC spinning. The material that exhibits the most effective synthesis will be subjected to further evaluation to assess its potential applicability in the photocatalytic degradation of pollutants.

  • Open Access

    Thermoplastic Starch with Maltodextrin: Preparation, Morphology, Rheology, and Mechanical Properties

    by Lata Rana, Saffana Kouka, Veronika Gajdosova, Beata Strachota, Magdalena Konefał, Vaclav Pokorny, Ewa Pavlova, Zdenek Stary, Jaroslav Lukes, Marek Patocka, et al.

    This work describes the preparation of highly homogeneous thermoplastic starches (TPS’s) with the addition of 0, 5, or 10 wt.% of maltodextrin (MD) and 0 or 3 wt.% of TiO2 nanoparticles. The TPS preparation was based on a two-step preparation protocol, which consisted in solution casting (SC) followed by melt mixing (MM). Rheology measurements at the typical starch processing temperature (120 °C) demonstrated that maltodextrin acted as a lubricating agent, which decreased the viscosity of the system. Consequently, the in situ measurement during the MM confirmed that the torque moments and real processing temperatures of all TPS/MD systems decreased in comparison with the pure TPS. The detailed characterization of morphology, thermomechanical properties, and local mechanical properties revealed that the viscosity decrease was accompanied by a slight decrease in the system homogeneity. The changes in the real processing temperatures might be quite moderate (ca 2–3 °C), but maltodextrin is a cheap and easy-to-add modifier, and the milder processing conditions are advantageous for both technical applications (energy savings) and biomedical applications (beneficial for temperature-sensitive additives, such as antibiotics).


  • Rheological properties of conductive polymer composites around the electrical percolation threshold

    by Zdeněk Starý, Helmut Münstedt

    The electrical conductivity of polymeric materials containing conductive particles shows a typical percolation behavior. Besides this effect adding the particles to a polymer matrix affects the rheological properties considerably. In the literature one can find some studies relating the electrical percolation to a comparable change of rheological quantities. The term “rheological percolation” is introduced; however, its definition is not consistent in the literature. In this contribution some literature data obtained from dynamic-mechanical measurements are discussed and confronted with own data from oscillatory and creep-recovery measurements. From a critical evaluation of the data it follows that rheological properties change continuously with the filler content in the range of the electrical percolation threshold. A simple model is proposed to explain the differences between the electrical and rheological behavior of polymer composites.