Jurij Krope
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jurij Krope has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
- Darko Goričanec
Faculty of Chemistry and Chemical Engineering, University of Maribor, Smetanova 17, 2000 Maribor, Slovenia
67 shared publications - Abdul Ghani Olabi
University of Sharjah
66 shared publications - Stanislav Božičnik
University of Maribor
66 shared publications - Ahmad Baroutaji
Aston University
2 shared publications Ahmed Al Makky
2 shared publicationsAwortwe Wilberforce
2 shared publications
Latest Publications
- Open Access
The Exploitation of Low-Temperature Hot Water Boiler Sources with High-Temperature Heat Pump Integration
The article presents an original and innovative technical solution for the exploitation of low-temperature excess heat from hot water boilers that use gas or liquid fuel for the needs of high-temperature heating in buildings or in industry. The primary fuel efficiency used for hot water boilers can be significantly increased by utilizing the excess low-temperature heat of flue gases that are discharged into the environment and thus also reduce CO2 emissions. Hot water systems usually operate at higher temperatures of the heating water, which is transported to the heat consumer via supply pipe, and the cooled heating water is returned to the hot water boiler via the return pipe. For the excess low-temperature heat exploitation of the flue gases from hot water boiler, it is necessary to install a condenser in the flue gas discharge pipe, where condensation of water vapour present in the flue gas heats water or a mixture of water and glycol. The heating water, which is cooled and returned from the heat consumer via the return pipe, is led to the condenser of the high-temperature heat pump, where it is preheated and then led to the hot water boiler, where it is heated to the final temperature. A computer simulation with the Aspen plus software package for the series or parallel connection of high-temperature heat pump to a hot water heating system and the economic analysis of the excess heat exploitation from the flue gases are also performed.
Open AccessThe Exploitation of Low-Temperature Hot Water Boiler Sources with High-Temperature Heat Pump Integration
The article presents an original and innovative technical solution for the exploitation of low-temperature excess heat from hot water boilers that use gas or liquid fuel for the needs of high-temperature heating in buildings or in industry. The primary fuel efficiency used for hot water boilers can be significantly increased by utilizing the excess low-temperature heat of flue gases that are discharged into the environment and thus also reduce CO2 emissions. Hot water systems usually operate at higher temperatures of the heating water, which is transported to the heat consumer via supply pipe, and the cooled heating water is returned to the hot water boiler via the return pipe. For the excess low-temperature heat exploitation of the flue gases from hot water boiler, it is necessary to install a condenser in the flue gas discharge pipe, where condensation of water vapour present in the flue gas heats water or a mixture of water and glycol. The heating water, which is cooled and returned from the heat consumer via the return pipe, is led to the condenser of the high-temperature heat pump, where it is preheated and then led to the hot water boiler, where it is heated to the final temperature. A computer simulation with the Aspen plus software package for the series or parallel connection of high-temperature heat pump to a hot water heating system and the economic analysis of the excess heat exploitation from the flue gases are also performed.
- 6 July 2017
- Published by University of Maribor
- p. 59-72
Waste Gasification with an Advanced 100 kW Dual Fluidized Bed Gasifier
- 6 July 2017
- Published by University of Maribor
- p. 59-72
Waste Gasification with an Advanced 100 kW Dual Fluidized Bed Gasifier
- 6 July 2017
- Published by University of Maribor
- p. 1-8
Study on the Comprehensive Utilization of City Kitchen Waste as a Resource in China
- 6 July 2017
- Published by University of Maribor
- p. 1-8
Study on the Comprehensive Utilization of City Kitchen Waste as a Resource in China
- 6 July 2017
- Published by University of Maribor
- p. 9-16
Investigation of the Electrode Geometry Configurations of Plasma Actuators
- 6 July 2017
- Published by University of Maribor
- p. 9-16
Investigation of the Electrode Geometry Configurations of Plasma Actuators
- 6 July 2017
- Published by University of Maribor
- p. 37-52
Characterisation of Proton Exchange Membrane (PEMFC) Fuel Cell Through Design of Experiment (DOE)
- 6 July 2017
- Published by University of Maribor
- p. 37-52
Characterisation of Proton Exchange Membrane (PEMFC) Fuel Cell Through Design of Experiment (DOE)
- 6 July 2017
- Published by University of Maribor
- p. 79-84
A Platform for Air Quality Monitoring Using Wireless Sensor Network - A Brief Review
- 6 July 2017
- Published by University of Maribor
- p. 79-84
A Platform for Air Quality Monitoring Using Wireless Sensor Network - A Brief Review
- 6 July 2017
- Published by University of Maribor
- p. 23-30
Capturing Sulfur Dioxide from Flue Gas by Iron (II) Hydroxide
- 6 July 2017
- Published by University of Maribor
- p. 23-30
Capturing Sulfur Dioxide from Flue Gas by Iron (II) Hydroxide
- Open Access
- 6 July 2017
- Published by University of Maribor
- p. 123-132
Composition and Application of Micro-Electro-Mechanical Systems (MEMS)
- 6 July 2017
- Published by University of Maribor
- p. 123-132
Open AccessComposition and Application of Micro-Electro-Mechanical Systems (MEMS)
- Open Access
- 6 July 2017
- Published by University of Maribor
- p. 13-22
Low Energy Processing of Polymeric Materials
- 6 July 2017
- Published by University of Maribor
- p. 13-22
Open AccessLow Energy Processing of Polymeric Materials
- Open Access
- 6 July 2017
- Published by University of Maribor
- p. 41-52
Optimisation of Wire Electro Discharge Machining Parameter Using Desirability Based Multi Objective RSM While Machining of Al6061–Cenosphere AMCs
- 6 July 2017
- Published by University of Maribor
- p. 41-52
Open AccessOptimisation of Wire Electro Discharge Machining Parameter Using Desirability Based Multi Objective RSM While Machining of Al6061–Cenosphere AMCs