Patrick Bischof
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Patrick Bischof has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Jaime Mata-Falcón
ETH Zurich
5 shared publications - Walter Kaufmann
Institute of Structural Engineering (IBK) ETH Zürich Zürich Switzerland
5 shared publications Walter Kaufmann
Institute of Structural Engineering, ETH Zurich
3 shared publicationsBenjamin Dillenburger
Institute of Technology in Architecture, Digital Building Technologies, ETH Zurich
2 shared publicationsJoris Burger
2 shared publications- Lukas Gebhard
ETH Zurich
2 shared publications
Latest Publications
- Open Access
- 30 March 2023
- Published by Elsevier in Engineering Structures
- Vol. 285
Experimental exploration of digitally fabricated connections for structural concrete
- 30 March 2023
- Published by Elsevier in Engineering Structures
- Vol. 285
Open AccessExperimental exploration of digitally fabricated connections for structural concrete
- Open Access
- 7 December 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (2) , 1835-1855
Digitally fabricated weak interfaces to reduce minimum reinforcement in concrete structures
Crack initiators in reinforced concrete structures can facilitate fulfilling the serviceability requirements. They can be used as a design parameter to diminish the minimum reinforcement for members subject to imposed deformation and exposed to the environment as they reduce the crack spacing and width when arranged close enough. While crack initiators in conventional concrete construction are cumbersome to provide (e.g., by construction joints or taperings), they are inherent to layered extrusion processes with digital fabrication technologies: the tensile strength is typically reduced locally in interfaces between layers. Rather than trying to avoid these weak interfaces , this paper discusses the potential of taking advantage of them to act as crack initiators reducing the minimum reinforcement content. A tension chord‐based model is developed to (i) account for the local strength reduction and (ii) predict the effect of weak interfaces on the expected crack spacing and width. As a key finding, the model predicts a reduction of the required minimum reinforcement ratio proportional to the locally decreased concrete tensile strength for a specified maximum crack width requirement under imposed deformations. An experimental campaign on five layered and three reference tension ties confirmed the clearly positive impact of weak interfaces on crack spacings and widths.
- 7 December 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (2) , 1835-1855
Open AccessDigitally fabricated weak interfaces to reduce minimum reinforcement in concrete structures
Crack initiators in reinforced concrete structures can facilitate fulfilling the serviceability requirements. They can be used as a design parameter to diminish the minimum reinforcement for members subject to imposed deformation and exposed to the environment as they reduce the crack spacing and width when arranged close enough. While crack initiators in conventional concrete construction are cumbersome to provide (e.g., by construction joints or taperings), they are inherent to layered extrusion processes with digital fabrication technologies: the tensile strength is typically reduced locally in interfaces between layers. Rather than trying to avoid these weak interfaces , this paper discusses the potential of taking advantage of them to act as crack initiators reducing the minimum reinforcement content. A tension chord‐based model is developed to (i) account for the local strength reduction and (ii) predict the effect of weak interfaces on the expected crack spacing and width. As a key finding, the model predicts a reduction of the required minimum reinforcement ratio proportional to the locally decreased concrete tensile strength for a specified maximum crack width requirement under imposed deformations. An experimental campaign on five layered and three reference tension ties confirmed the clearly positive impact of weak interfaces on crack spacings and widths.
- Open Access
- 26 September 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (3) , 3251-3263
Modeling statically indeterminate reinforced concrete slabs and beams under fire conditions
EN 1992‐1‐2 generally limits the redistribution of bending moments from the intermediate supports to the span for continuous reinforced concrete slabs and beams in fire conditions to 15%. While higher redistributions are allowed if sufficient rotation capacity is provided, EN 1992‐1‐2 does not indicate how to assess the rotation capacity. However, plastic hinges caused by the rotation demand under fire conditions are highly relevant when predicting the global response and structural safety of a structure (partially) exposed to fire. Rotation capacity is specifically necessary at support regions subjected to negative bending and fire, where concrete in compression undergoes thermal degradation while the tension chord remains close to ambient temperature. This article presents a comprehensive model for the behavior of statically indeterminate members in fire conditions, enabling to estimate whether sufficient rotation capacity is provided. Material properties specified by EN 1992‐1‐2 are applied combined with complementary considerations concerning (i) the biaxial compressive strength of concrete, (ii) strain hardening and limitations of the ultimate strain of reinforcement, as well as (iii) tension stiffening. Tension stiffening detrimentally influences the ductility of the tension chord, limiting the rotation capacity. When comparing predictions obtained by the model to experimental results given in the literature, the correlation is good for the investigated one‐way continuous slabs and beams. However, considerable uncertainty exists regarding the type of concrete aggregate used. Moreover, uncertainties concerning the behavior of concrete under compression and fire conditions are highly relevant for modeling the region of supports with rotational restraint.
- 26 September 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (3) , 3251-3263
Open AccessModeling statically indeterminate reinforced concrete slabs and beams under fire conditions
EN 1992‐1‐2 generally limits the redistribution of bending moments from the intermediate supports to the span for continuous reinforced concrete slabs and beams in fire conditions to 15%. While higher redistributions are allowed if sufficient rotation capacity is provided, EN 1992‐1‐2 does not indicate how to assess the rotation capacity. However, plastic hinges caused by the rotation demand under fire conditions are highly relevant when predicting the global response and structural safety of a structure (partially) exposed to fire. Rotation capacity is specifically necessary at support regions subjected to negative bending and fire, where concrete in compression undergoes thermal degradation while the tension chord remains close to ambient temperature. This article presents a comprehensive model for the behavior of statically indeterminate members in fire conditions, enabling to estimate whether sufficient rotation capacity is provided. Material properties specified by EN 1992‐1‐2 are applied combined with complementary considerations concerning (i) the biaxial compressive strength of concrete, (ii) strain hardening and limitations of the ultimate strain of reinforcement, as well as (iii) tension stiffening. Tension stiffening detrimentally influences the ductility of the tension chord, limiting the rotation capacity. When comparing predictions obtained by the model to experimental results given in the literature, the correlation is good for the investigated one‐way continuous slabs and beams. However, considerable uncertainty exists regarding the type of concrete aggregate used. Moreover, uncertainties concerning the behavior of concrete under compression and fire conditions are highly relevant for modeling the region of supports with rotational restraint.
- Open Access
- 23 September 2022
- Published by Rilem Publications SARL in RILEM Technical Letters
- Vol. 7, 68-78
Digitally fabricated ribbed concrete floor slabs: a sustainable solution for construction
The concrete used in floor slabs accounts for large greenhouse gas emissions in building construction. Solid slabs, often used today, consume much more concrete than ribbed slabs built by pioneer structural engineers like Hennebique, Arcangeli and Nervi. The first part of this paper analyses the evolution of slab systems over the last century and their carbon footprint, highlighting that ribbed slabs have been abandoned mainly for the sake of construction time and cost efficiency. However, highly material-efficient two-way ribbed slabs are essential to reduce the environmental impact of construction. Hence, the second part of this paper discusses how digital fabrication can help to tackle this challenge and presents four concrete floor systems built with digitally fabricated formwork. The digital fabrication technologies employed to produce these slab systems are digital cutting, binder-jetting, polymer extrusion and 3D concrete printing. The presented applications showcase a reduction in concrete use of approximately 50% compared to solid slabs. However, the digitally fabricated complex formworks produced were wasteful and/or labour-intensive. Further developments are required to make the digital processes sustainable and competitive by streamlining the production, using low carbon concrete mixes as well as reusing and recycling the formwork or structurally activating stay-in-place formwork.
- 23 September 2022
- Published by Rilem Publications SARL in RILEM Technical Letters
- Vol. 7, 68-78
Open AccessDigitally fabricated ribbed concrete floor slabs: a sustainable solution for construction
The concrete used in floor slabs accounts for large greenhouse gas emissions in building construction. Solid slabs, often used today, consume much more concrete than ribbed slabs built by pioneer structural engineers like Hennebique, Arcangeli and Nervi. The first part of this paper analyses the evolution of slab systems over the last century and their carbon footprint, highlighting that ribbed slabs have been abandoned mainly for the sake of construction time and cost efficiency. However, highly material-efficient two-way ribbed slabs are essential to reduce the environmental impact of construction. Hence, the second part of this paper discusses how digital fabrication can help to tackle this challenge and presents four concrete floor systems built with digitally fabricated formwork. The digital fabrication technologies employed to produce these slab systems are digital cutting, binder-jetting, polymer extrusion and 3D concrete printing. The presented applications showcase a reduction in concrete use of approximately 50% compared to solid slabs. However, the digitally fabricated complex formworks produced were wasteful and/or labour-intensive. Further developments are required to make the digital processes sustainable and competitive by streamlining the production, using low carbon concrete mixes as well as reusing and recycling the formwork or structurally activating stay-in-place formwork.
- Open Access
- 5 September 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (2) , 2592-2605
Assessment of parameters influencing the behavior of statically indeterminate reinforced concrete slabs and beams under fire conditions
This paper investigates the effect of material properties, boundary conditions, and related modeling and design uncertainties on the fire behavior of statically indeterminate reinforced concrete beams and slabs by means of a parametric study based on a comprehensive model. This model uses material properties specified by EN 1992‐1‐2, complemented by considerations concerning the biaxial compressive strength of concrete, strain hardening and limitations of the ultimate strain of reinforcement, as well as tension stiffening. The parametric study identifies and explains the most influential parameters governing the fire behavior of statically indeterminate reinforced concrete beams and slabs. The implementation and generalization of these parameters are evaluated and compared to current design rules in EN 1992‐1‐2 derived from the evaluation of experimental testing and real fire cases. Overall, the detailing rules given in EN 1992‐1‐2 are found to be reasonably safe, and they can be easily used for practical applications. Furthermore, the results of the study indicate that model predictions for the studied statically indeterminate systems are subject to considerable uncertainty because (i) information on the used material is possibly incomplete and (ii) the models given in design codes do not (or only insufficiently) cover all relevant aspects of the thermo‐mechanical behavior. Specifically, the concrete aggregate type with its corresponding thermal expansion, the strain hardening properties of the reinforcement and tension stiffening with its detrimental effect on the ductility of the tension chord may affect the rating across several standard fire resistance times of statically indeterminate reinforced concrete members subjected to bending.
- 5 September 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (2) , 2592-2605
Open AccessAssessment of parameters influencing the behavior of statically indeterminate reinforced concrete slabs and beams under fire conditions
This paper investigates the effect of material properties, boundary conditions, and related modeling and design uncertainties on the fire behavior of statically indeterminate reinforced concrete beams and slabs by means of a parametric study based on a comprehensive model. This model uses material properties specified by EN 1992‐1‐2, complemented by considerations concerning the biaxial compressive strength of concrete, strain hardening and limitations of the ultimate strain of reinforcement, as well as tension stiffening. The parametric study identifies and explains the most influential parameters governing the fire behavior of statically indeterminate reinforced concrete beams and slabs. The implementation and generalization of these parameters are evaluated and compared to current design rules in EN 1992‐1‐2 derived from the evaluation of experimental testing and real fire cases. Overall, the detailing rules given in EN 1992‐1‐2 are found to be reasonably safe, and they can be easily used for practical applications. Furthermore, the results of the study indicate that model predictions for the studied statically indeterminate systems are subject to considerable uncertainty because (i) information on the used material is possibly incomplete and (ii) the models given in design codes do not (or only insufficiently) cover all relevant aspects of the thermo‐mechanical behavior. Specifically, the concrete aggregate type with its corresponding thermal expansion, the strain hardening properties of the reinforcement and tension stiffening with its detrimental effect on the ductility of the tension chord may affect the rating across several standard fire resistance times of statically indeterminate reinforced concrete members subjected to bending.
- 25 June 2022
- Published by Springer Nature
- p. 430-435
Pre-installed Reinforcement for 3D Concrete Printing
- 25 June 2022
- Published by Springer Nature
- p. 430-435
Pre-installed Reinforcement for 3D Concrete Printing
- 1 January 2017
- Published by International Association for Bridge and Structural Engineering (IABSE)
- p. 239-246
Re-thinking traditional construction processes: Accelerated channel construction
For the first time in Zurich, rectangular precast concrete elements were used for constructing man size sewers in open trenches by realising the projects “Riedtlistrasse” and “Moränenstrasse”. Thanks to an innovative mounting system developed by DSE systems, the precise mounting of one element took no longer than 15 minutes on a previously prepared lean concrete surface. Thus, the use of precast elements allowed a substantial reduction of construction time in comparison to the traditionally built sewers with cast in-place concrete. The concept of the construction process was developed at an early project state in creative and innovative teams consisting of engineers, precast contractor, and owner/ client. Working together at such an early stage of the project was crucial for finding innovative solutions that fit all requirements. These innovative solutions enabled the setting of new milestones in Zurich sewer construction.
- 1 January 2017
- Published by International Association for Bridge and Structural Engineering (IABSE)
- p. 239-246
Re-thinking traditional construction processes: Accelerated channel construction
For the first time in Zurich, rectangular precast concrete elements were used for constructing man size sewers in open trenches by realising the projects “Riedtlistrasse” and “Moränenstrasse”. Thanks to an innovative mounting system developed by DSE systems, the precise mounting of one element took no longer than 15 minutes on a previously prepared lean concrete surface. Thus, the use of precast elements allowed a substantial reduction of construction time in comparison to the traditionally built sewers with cast in-place concrete. The concept of the construction process was developed at an early project state in creative and innovative teams consisting of engineers, precast contractor, and owner/ client. Working together at such an early stage of the project was crucial for finding innovative solutions that fit all requirements. These innovative solutions enabled the setting of new milestones in Zurich sewer construction.