SYSatoshi Yamane

Satoshi Yamane

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Satoshi Yamane has a total of 37 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Measurement of ozone concentration in breathing zone during arc welding

    by S. Yamane, Y. Xia, H. Ihara

    In 2024, Japan set 0.1 ppm as the administrative levels—assessed as a short-term (15 min) exposure limit—for ozone in the breathing zone. Ozone is reportedly generated by the metal inert gas and tungsten inert gas welding of aluminum. The Japan Engineering Welding Society has investigated welding in shipyards, bridge construction, and tank assembly. A field study on ozone concentrations in various welding environments shows that ozone is generated by other welding processes as well. However, except in the case of pulsed gas metal arc welding, measured ozone concentrations are below the 0.1 ppm the administrative levels during short-term (15 min) exposure. Moreover, measured ozone concentrations vary depending on the welding environment, including the welding method, welder posture, and airflow. Therefore, this study investigated differences in measured ozone concentrations during arc welding. Welding work environments were recreated, and ozone concentrations were measured. Additionally, the intensity of ultraviolet light, a cause of ozone generation, was measured, and its relationship with ozone concentration was examined.

  • Open Access

    Position-Aware Coupling Between Ozone and Welding Fume Peaks Under Local Exhaust Ventilation

    by Yuxiong Xia, Satoshi Yamane, Weixi Wang, Hiroki Ihara, Jidong Lu, Yuxi Luo

    Real-time management of short-term ozone peaks during arc welding remains challenging because ventilation- and enclosure-defined transport boundaries can create strong position-dependent peak behavior, even under fixed process settings. This study establishes a coordinate-referenced, event-level monitoring and analysis framework to quantify ozone–fume peak coupling under a controlled local exhaust ventilation (LEV) suction boundary during CO2 arc welding. A controlled process–environment testbed with a defined suction condition was implemented, and synchronized ozone and fume signals were acquired at three sampling points referenced to the arc position and the LEV inlet direction. The particulate channel was anchored to a PM4 gravimetric reference, yielding a condition-specific traceable CPM-to-mass conversion factor K1 of 1.76 × 10−2 mg/(m3·CPM) and enabling standardized peak-fume endpoints on a mass-concentration scale. The primary inferential analysis used the curtain-on dataset, comprising 21 sessions and 42 event-level records balanced across three sampling points. Under the same suction boundary, peak coupling was strongly monitoring-coordinate dependent: LEV-aligned locations showed statistically supported ln–ln scaling between peak ozone and peak fume, whereas the opposite-side location did not exhibit statistically supported scaling; a pooled point-parameterized ln–ln model achieved an adjusted R2 of 0.777. As a descriptive control-relevant contrast, adding a curtain enclosure under continuous LEV produced strong event-level ozone peak suppression at LEV-aligned locations, with a maximum reduction of 87.8%, while attenuation at the opposite-side location remained limited. Overall, the results provide a ventilation-boundary-consistent, coordinate-specific basis for monitoring placement and control evaluation, identifying where peak translation is supported and where direct ozone monitoring remains necessary.

  • Drone DETR: enhancing real-time detection transformer for drone small object imagery

    by Weixi Wang, Ye Liu, Zhouzhou Cui, Liang Shan, Bo-Chao Zheng, Zhong Wei, Xiaoqing Zhang, Satoshi Yamane


  • Open Access

    Vision-Based Closed-Loop Control of Pulsed MAG Welding Using Otsu-Segmented Arc Features

    by Yuxi Luo, Satoshi Yamane, Weixi Wang, Rei Tsumori, Kohei Ochiai, Jidong Lu, Yuxiong Xia

    While modern power sources have improved process stability, real-time monitoring and feedback control remain essential for ensuring consistent weld quality under dynamic conditions. To address this need, a vision-based closed-loop control system was developed for pulsed Metal-Active Gas (MAG) welding. The system dynamically adjusts the welding speed based on real-time visual feedback in the welding process. Otsu thresholding combined with morphological operations was applied to molten pool images for brightness-based feature extraction. These features, representing the dynamic behavior of the molten pool, were incorporated into a feedback loop for real-time control. Without relying on complex model-based prediction or sensor fusion, the proposed method reduces fluctuations in weld bead geometry and lowers the occurrence of defects. The experimental results showed that, under optimized control conditions and after a steady welding state was achieved, the weld bead’s height deviation exhibited an average standard deviation of 0.08 mm, and a process stability rate of 92%. The combination of conventional hardware and straightforward image processing makes the proposed approach practical for industrial implementation.


  • Open Access

    Visual welding process control in Pulsed GMAW using Otsu-thresholded features

    by Yuxi Luo, Satoshi Yamane, Weixi Wang, Rei Tsumori, Kohei Ochiai, Jidong Lu, Yuxiong Xia

    Pulsed Gas metal arc welding (GMAW) technology is a commonly useful welding technology worldwide, and it’s still a difficult point to keep a safe and stable state in the welding process due to the complex variations. In this study, molten pools serve as a crucial indicator for evaluating welding states. In the pulsed GMAW process, metal transfer predominantly occurs through molten pools. To facilitate effective monitoring and control, a visual-sensor-based control system was developed. By analyzing the physical characteristics of the welding arc under varying welding speeds, real-time images are captured and processed using Otsu’s thresholding method to segment and extract key features. These extracted features are then fed into a closed-loop feedback control system, enabling dynamic adjustment of welding parameters in response to changes in the welding state. Compared with traditional approaches, this study improves welding process stability and reduces the probabilities of weld defects. The results demonstrate that under actively controlled welding conditions, a high-quality weld bead was achieved. The overall average deviation of the weld bead height remained within ± 0.03 mm, and the average variance within ± 0.31 mm², indicating robust control of the welding process. The results maintained 97% of the stability margin. This study provides a foundation for intelligent and adaptive control in automated welding applications.


  • Open Access

    Detection of molten pool state using ResNet50 and control of molten pool penetration in CO2 gas shielded arc welding

    by Satoshi Yamane, ChuanZhi Wang, Takahito Nakamura, Takuya Nagai, Keito Ishizaki

    In V groove butt welding with a ceramic backing material, the molten pool should penetrate well. Regardless of the gap fluctuations, the molten pool must maintain a good penetration shape. For this purpose, the molten pool state is detected using ResNet50 as one of the deep learning. The molten pool using a CMOS camera is taken. Fundamental experiments are performed, and images are collected for learning of ResNet50. Good estimation results are obtained for untraining data. The gap and its center are detected processing the molten pool images. The seam tracking is carried out using PI controller, with inputs being the difference between the wire tip and the gap center, and the output is Y axis position. The weaving width is adjusted to fit the gap. The molten pool state is controlled adjusting the travel speed of the welding torch, to keep constant the arc position, because the state of the molten pool depends on the arc position. If there is gap fluctuation as the disturbance and the reference of the arc position is same, it is difficult to get the same penetration of the molten pool. Therefore, the reference according to the output of ResNet50 is adjusted. Molten pool control is based on PI controller with the input is the difference between the arc position and its reference, and the output is the travel speed. The control performance is verified in a case where the gap varies from 7 to 3 mm, and good results are obtained.


  • Enhancing small traffic sign recognition based on an improved YOLOv8 algorithm

    by Xiaoqing Zhang, Weixi Wang, Qi Wang, Liang Shan, Satoshi Yamane, Bochao Zheng, Sifan Liu, Tianxing Shen, Dongming Ge


  • Open Access

    Weld Pool Boundary Detection Based on the U-Net Algorithm and Weld Seam Tracking in Plasma Arc Welding

    by Jidong Lu, Satoshi Yamane, Weixi Wang, Ning Li, Siqi Wang, Yuxiong Xia

    Plasma arc welding can achieve high-quality welding joints in high-strength manufacturing fields, such as aviation and automotive, and improve production efficiency. It is important to observe the weld pool state in real-time in robot automatic welding. However, the electrodes of the plasma welding torch cannot be observed from the outside. Teaching the weld line to torch in real-time to be observable to humans will be difficult. Also, it is difficult to process the image to obtain the position of the weld line in K-PAW. In this study, a camera was utilized to observe the weld pool. The authors estimate the weld line position in real time by image processing based on U-Net prediction. The U-Net model demonstrates sufficient prediction where the accuracy reached 99.5% for the training data and 96.5% for the test data recognition. Moreover, a control method utilized weld line position estimated from the boundary area to verify the effectiveness of this prediction model from 3 mm within the deviation of 1 mm, which is within the range of permissible welding errors. It could reduce image processing errors in the weld pool image and provide higher recognition accuracy than image processing. Combining vision sensing technologies and deep learning methods will provide new technologies to enable higher welding precision and improve welding quality. It could also accelerate the development of welding technology in the intelligent manufacturing field.


  • Open Access

    Microstructure and Mechanical Properties of Ring-mash-welded Powertrain Parts

    by Yasuo Kadoya, Yuki Oshinoh, Satoshi Yamane

    The components of the powertrain that transmits power to an engine drive have been fabricated with various welding techniques, such as laser welding and gas metal arc welding. To reduce the weight of these components and hence the energy consumption of automobiles, the authors propose ring-mash welding as a component-joining method, which works by solid-phase bonding. The specimens were raw SCM415H chromium molybdenum steel, an alloy steel provided for machine structural use. Temperature and pressure are important parameters of joining. The proposed ring-mash welding relies on Joule heat generation. The bonding area softens during heating, facilitating solid-phase bonding. To clarify the bonding mechanism of ring-mash welding, the bonding condition was investigated under different applied pressures and electric currents. Although spatter was generated during bonding under excessive heat conditions, it was suppressed by increasing the applied pressure. The bonding strength depended more on the current than on the applied pressure. A small continuous gap appeared at the bonding interface under low current, which became intermittent, and eventually disappeared as the current increased. The bonding area was quenched by the temperature rise and rapid quenching during the joining process and an altered microstructure with increased hardness was formed. The optimal bonding conditions were determined.

  • Open Access

    Adaptive Control by Convolutional Neural Network in Plasma Arc Welding System

    by Satoshi Yamane, Kouki Matsuo

    Plasma arc welding (PAW) was employed in joining thick materials with groove. Due to the high-density plasma arc, keyhole welding was used in the butt welding. The gap might be taken in places due to the heat distortion during the welding. To achieve a high-quality welding, the adaptive control is required according to the gap. The authors tried to apply CMOS camera to obtain information from the top surface and achieve synchronization between the camera shutter and welding current. Thus, a clear image of the weld pool with the keyhole and the gap was taken. The brightness distribution in the front of the weld pool becomes uneven due to the plasma arc. To classify the gap and select the welding conditions, such as the welding current and the plasma gas flow rate, the authors used one of the deep learning algorithms, convolutional neural network (CNN). In the training and testing data, the performance of the CNN was found to be satisfactory. However, if the plasma torch does not trace the welding line, the pool image will be different from the training image. Hence, the CNN will not be able to estimate the correct gap. To avoid this, the authors detected the welding line from the pool image and selected the image area near the welding line as the input of the CNN, i.e., the input area is selected based on the image obtained during the welding. The validity of the proposed method was verified by the welding experiments.