Juhani Nissilä
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Juhani Nissilä has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Jouni Laurila
Intelligent Machines and Systems University of Oulu PO Box 4200 90014 Oulu Finland
6 shared publications - Mika Pylvänäinen
Intelligent Machines and Systems University of Oulu PO Box 4200 90014 Oulu Finland
5 shared publications - Ville-Valtteri Visuri
Process Metallurgy Research Unit University of Oulu Oulu Finland
5 shared publications - Toni Liedes
University of Oulu
4 shared publications - Esko K. Juuso
Control Engineering Environmental and Chemical Engineering Faculty of Technology University of Oulu P.O.Box 4300 FI-90014 Finland
2 shared publications - Konsta Karioja
University of Oulu
2 shared publications
Latest Publications
- Open Access
- 29 April 2026
- Published by Wiley in Steel Research International
- Vol. 97 (9) , 4684-4713
Bath Vibration During Open Eye Formation in a Physical Model of a Steelmaking Ladle
Secondary metallurgy allows precise adjustment of steel's chemical composition and temperature prior to casting. Alloying typically uses lumpy material or wire fed through an open eye in the slag layer formed by bottom gas injection to enhance mixing efficiency. However, visual observation of the open eye is often limited, particularly during vacuum tank degassing. To overcome this challenge, the present study examines vibration measurements as indirect indicators of gas stirring efficiency and open eye behavior, using a 1:5 scale physical model of a 150‐ton steelmaking ladle. The results indicate that vibration magnitude—defined as the root mean square (RMS) of acceleration—and open eye area, along with their variances, increased with higher air flow rates. Vibration responses generally stabilized faster than the open eye, except above 5 kHz in the vessel's lower region. Although limiting the frequency bandwidth to 0–6.0 kHz slightly reduced prediction accuracy compared to the full 0–12.8 kHz range, it still produced satisfactory results. Notably, open eye size was reliably predicted using vibration data alone, independent of flow rate measurements. The highest prediction performance was achieved using vibration data from accelerometer locations Acc5 and Acc6 within the 0–6.0 kHz range, and from Acc2 and Acc5 within the 0–12.8 kHz bandwidth.
- 29 April 2026
- Published by Wiley in Steel Research International
- Vol. 97 (9) , 4684-4713
Open AccessBath Vibration During Open Eye Formation in a Physical Model of a Steelmaking Ladle
Secondary metallurgy allows precise adjustment of steel's chemical composition and temperature prior to casting. Alloying typically uses lumpy material or wire fed through an open eye in the slag layer formed by bottom gas injection to enhance mixing efficiency. However, visual observation of the open eye is often limited, particularly during vacuum tank degassing. To overcome this challenge, the present study examines vibration measurements as indirect indicators of gas stirring efficiency and open eye behavior, using a 1:5 scale physical model of a 150‐ton steelmaking ladle. The results indicate that vibration magnitude—defined as the root mean square (RMS) of acceleration—and open eye area, along with their variances, increased with higher air flow rates. Vibration responses generally stabilized faster than the open eye, except above 5 kHz in the vessel's lower region. Although limiting the frequency bandwidth to 0–6.0 kHz slightly reduced prediction accuracy compared to the full 0–12.8 kHz range, it still produced satisfactory results. Notably, open eye size was reliably predicted using vibration data alone, independent of flow rate measurements. The highest prediction performance was achieved using vibration data from accelerometer locations Acc5 and Acc6 within the 0–6.0 kHz range, and from Acc2 and Acc5 within the 0–12.8 kHz bandwidth.
- 27 June 2024
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 35 (9) , 096136
Cyclostationarity and real order derivatives in roller bearing fault detection
Various methods are used in the field of machine diagnostics for recognizing cyclostationarity in signals. The real order derivatives of vibration signals, however, have been rarely reported from the perspective of their effect on the performance of cyclostationarity detection methods. In this paper, we use real order derivatives together with spectral correlation, spectral coherence and squared envelope. Our results suggest that adjusting the order of derivative can enhance the analysis outcome of spectral correlation and squared envelope in particular. Remarkably, the results also suggest that squared envelope, when used alongside real-order derivatives, may replace spectral correlation and spectral coherence. This approach allows obtaining results with reduced computational power, making it advantageous for applications like industrial edge computing, where cost-effective hardware is crucial.
- 27 June 2024
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 35 (9) , 096136
Cyclostationarity and real order derivatives in roller bearing fault detection
Various methods are used in the field of machine diagnostics for recognizing cyclostationarity in signals. The real order derivatives of vibration signals, however, have been rarely reported from the perspective of their effect on the performance of cyclostationarity detection methods. In this paper, we use real order derivatives together with spectral correlation, spectral coherence and squared envelope. Our results suggest that adjusting the order of derivative can enhance the analysis outcome of spectral correlation and squared envelope in particular. Remarkably, the results also suggest that squared envelope, when used alongside real-order derivatives, may replace spectral correlation and spectral coherence. This approach allows obtaining results with reduced computational power, making it advantageous for applications like industrial edge computing, where cost-effective hardware is crucial.
- Open Access
- 1 September 2023
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 54 (6) , 1-22
Vibration and Audio Measurements in the Monitoring of Basic Oxygen Furnace Steelmaking
- 1 September 2023
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 54 (6) , 1-22
Open AccessVibration and Audio Measurements in the Monitoring of Basic Oxygen Furnace Steelmaking
- 19 July 2023
- Published by Springer Nature
- p. 111-123
Real Order Derivatives and Spectral Norms in Fault Detection
- 19 July 2023
- Published by Springer Nature
- p. 111-123
Real Order Derivatives and Spectral Norms in Fault Detection
- 19 July 2023
- Published by Springer Nature
- p. 31-42
Detecting Gas Injection Problems in Vacuum Tank Degassing Using Measurements of Multiple Variables
- 19 July 2023
- Published by Springer Nature
- p. 31-42
Detecting Gas Injection Problems in Vacuum Tank Degassing Using Measurements of Multiple Variables
- Open Access
- 28 May 2023
- Published by Wiley in Steel Research International
- Vol. 94 (9)
Effect of Gas Forming Compounds on the Vibration of a Submerged Lance in Hot Metal Desulfurization
Hot metal desulfurization is the main process step for removing sulfur in blast furnace‐based steelmaking. A desulfurization reagent is pneumatically injected into the hot metal through a submerged lance causing it to vibrate. The aim of this study is to develop a mechanical vibration measurement‐based method that can detect changes in the gas‐forming properties of the reagent. The detection is performed using Elastic Net regression and eXtreme Gradient Boosting‐based classification models the classification performance of which is compared. The lance aging causes changes in its dynamic characteristics, and the disturbing effect of this is removed from the measured data of the lance vibration prior to classification by means of a developed cleaning algorithm. The best classification performance in detecting changes in the gas‐forming properties, with an area under the receiver operating characteristic curve of 0.916 and Matthews correlation coefficient of 0.699, is achieved using an Elastic Net regression‐based classification model. The results of this work serve as a basis for developing industrial applications in which the effective utilization of the excitation, such as vibrations generated by the gas formation can be utilized for process monitoring and as a soft sensor for predicting the reagent‐induced process variance.
- 28 May 2023
- Published by Wiley in Steel Research International
- Vol. 94 (9)
Open AccessEffect of Gas Forming Compounds on the Vibration of a Submerged Lance in Hot Metal Desulfurization
Hot metal desulfurization is the main process step for removing sulfur in blast furnace‐based steelmaking. A desulfurization reagent is pneumatically injected into the hot metal through a submerged lance causing it to vibrate. The aim of this study is to develop a mechanical vibration measurement‐based method that can detect changes in the gas‐forming properties of the reagent. The detection is performed using Elastic Net regression and eXtreme Gradient Boosting‐based classification models the classification performance of which is compared. The lance aging causes changes in its dynamic characteristics, and the disturbing effect of this is removed from the measured data of the lance vibration prior to classification by means of a developed cleaning algorithm. The best classification performance in detecting changes in the gas‐forming properties, with an area under the receiver operating characteristic curve of 0.916 and Matthews correlation coefficient of 0.699, is achieved using an Elastic Net regression‐based classification model. The results of this work serve as a basis for developing industrial applications in which the effective utilization of the excitation, such as vibrations generated by the gas formation can be utilized for process monitoring and as a soft sensor for predicting the reagent‐induced process variance.
- Open Access
Fourier decay of absolutely and Hölder continuous functions with infinitely or finitely many oscillations
The main result of this paper is, that if we suppose that a function is absolutely continuous and uniformly H\"older continuous and that it's finite difference function does not oscillate infinitely often on a bounded interval, then the decay rate of its Fourier coefficients can be estimated exactly. This rate of decay predicts the same uniform H\"older continuity but the two other conditions are not necessary. Several examples from literature and by the author show that none of the assumptions can be relaxed without weakening the decay for some functions. The uniform H\"older continuity of chirps and the decay of their Fourier coefficients are studied. The main result is then applied in the estimation of the error of numerical Weyl fractional derivatives calculated using the discrete Fourier transform. The main result is also extended to Fourier transforms.
Open AccessFourier decay of absolutely and Hölder continuous functions with infinitely or finitely many oscillations
The main result of this paper is, that if we suppose that a function is absolutely continuous and uniformly H\"older continuous and that it's finite difference function does not oscillate infinitely often on a bounded interval, then the decay rate of its Fourier coefficients can be estimated exactly. This rate of decay predicts the same uniform H\"older continuity but the two other conditions are not necessary. Several examples from literature and by the author show that none of the assumptions can be relaxed without weakening the decay for some functions. The uniform H\"older continuity of chirps and the decay of their Fourier coefficients are studied. The main result is then applied in the estimation of the error of numerical Weyl fractional derivatives calculated using the discrete Fourier transform. The main result is also extended to Fourier transforms.
- Open Access
- 16 March 2020
- Published by Wiley in Steel Research International
- Vol. 91 (6)
Vibration‐Based Monitoring of Gas‐Stirring Intensity in Vacuum Tank Degassing
Liquid steel is typically stirred in a vacuum tank using argon gas injection to achieve a homogeneous composition and high‐purity steel. The aim of this work is to study the effect of vessel vibration on the operational state monitoring of the gas stirring in a vacuum tank degasser. Following an extensive analysis of vibration features, the root mean square (RMS) of vertical velocity is found to be the best feature for the measurement of the stirring intensity caused by the volumetric gas injection rate into the ladle. Smoothing is conducted using a centered median filter with a window length of 21 s. In this work, the operational state monitoring of gas stirring is described using a ladle responsiveness value (LRV). This describes the ability of a ladle to generate the maximum amount of vibration with the minimum amount of argon gas. The LRV summarized for each ladle reveals significant differences between them. Correspondingly, a rolling ladle responsiveness value (rLRV) is used for online monitoring of possible gas leakages. The rLRV can also be used for the online monitoring of the stirring efficiency and as its comparison with the overall efficiency of a specific ladle or all ladles.
- 16 March 2020
- Published by Wiley in Steel Research International
- Vol. 91 (6)
Open AccessVibration‐Based Monitoring of Gas‐Stirring Intensity in Vacuum Tank Degassing
Liquid steel is typically stirred in a vacuum tank using argon gas injection to achieve a homogeneous composition and high‐purity steel. The aim of this work is to study the effect of vessel vibration on the operational state monitoring of the gas stirring in a vacuum tank degasser. Following an extensive analysis of vibration features, the root mean square (RMS) of vertical velocity is found to be the best feature for the measurement of the stirring intensity caused by the volumetric gas injection rate into the ladle. Smoothing is conducted using a centered median filter with a window length of 21 s. In this work, the operational state monitoring of gas stirring is described using a ladle responsiveness value (LRV). This describes the ability of a ladle to generate the maximum amount of vibration with the minimum amount of argon gas. The LRV summarized for each ladle reveals significant differences between them. Correspondingly, a rolling ladle responsiveness value (rLRV) is used for online monitoring of possible gas leakages. The rLRV can also be used for the online monitoring of the stirring efficiency and as its comparison with the overall efficiency of a specific ladle or all ladles.
- 5 March 2019
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 30 (4) , 045102
Diagnosing simultaneous faults using the local regularity of vibration signals
The regularity of the vibration signals measured from a rotating machine is often affected by the condition of the machine. The fractional order of regularity can be measured using the definition of Hölder continuity. In this paper, we review the connection between the pointwise Hölder regularity of a signal and its wavelet transform. We calculate the wavelet transform modulus of acceleration measurements from a test rig. The effects of different faults were recorded, such as unbalance, the coupling misalignment of a claw clutch, the absence of lubrication in a ball bearing, the absence of the bearing’s cage, and their combinations. An analysis of the estimated isolated pointwise regularities from the wavelet transform modulus maxima ridges shows that the faults often cause irregularities in the signals and that their locations and frequencies can be used in diagnosing the faults. Coupling misalignment and the absence of lubrication in a ball bearing both cause impact-like vibrations, but these impacts have positive and negative regularities in the case of a coupling misalignment and mainly negative in the case of a dry bearing. Unbalance is best diagnosed from the integrals of the acceleration signals using traditional methods. In diagnosing the misalignment, bearing problems and simultaneous faults, the local regularity analysis outperforms the use of high order norms of differentiated acceleration measurements (i.e. jerk and snap signals). Using just three features (the number of local irregularities in an acceleration signal, their mean Hölder regularity and the arithmetic mean of the absolute values of a velocity signal), a quadratic classifier can be constructed whose estimated classification error is only 0.3%.
- 5 March 2019
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 30 (4) , 045102
Diagnosing simultaneous faults using the local regularity of vibration signals
The regularity of the vibration signals measured from a rotating machine is often affected by the condition of the machine. The fractional order of regularity can be measured using the definition of Hölder continuity. In this paper, we review the connection between the pointwise Hölder regularity of a signal and its wavelet transform. We calculate the wavelet transform modulus of acceleration measurements from a test rig. The effects of different faults were recorded, such as unbalance, the coupling misalignment of a claw clutch, the absence of lubrication in a ball bearing, the absence of the bearing’s cage, and their combinations. An analysis of the estimated isolated pointwise regularities from the wavelet transform modulus maxima ridges shows that the faults often cause irregularities in the signals and that their locations and frequencies can be used in diagnosing the faults. Coupling misalignment and the absence of lubrication in a ball bearing both cause impact-like vibrations, but these impacts have positive and negative regularities in the case of a coupling misalignment and mainly negative in the case of a dry bearing. Unbalance is best diagnosed from the integrals of the acceleration signals using traditional methods. In diagnosing the misalignment, bearing problems and simultaneous faults, the local regularity analysis outperforms the use of high order norms of differentiated acceleration measurements (i.e. jerk and snap signals). Using just three features (the number of local irregularities in an acceleration signal, their mean Hölder regularity and the arithmetic mean of the absolute values of a velocity signal), a quadratic classifier can be constructed whose estimated classification error is only 0.3%.
- Open Access
- 19 December 2018
- Published by Linkoping University Electronic Press
- No. 142,p. 422-432
Extracting Vibration Severity Time Histories from Epicyclic Gearboxes
Here is information on how to publish, spread your research, and search for your publications. Most of LiU's research publications are directly imported into DiVA from the Web of Science. Before registering a publication, always check if the publication is already in DiVA!
- 19 December 2018
- Published by Linkoping University Electronic Press
- No. 142,p. 422-432
Open AccessExtracting Vibration Severity Time Histories from Epicyclic Gearboxes
Here is information on how to publish, spread your research, and search for your publications. Most of LiU's research publications are directly imported into DiVA from the Web of Science. Before registering a publication, always check if the publication is already in DiVA!