Xuhe Wang
Research Subjects
Xuhe Wang has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Baoshan Zhu
Tsinghua University
2 shared publications - Daqing Qin
Harbin Institute of Large Electrical Machinery, Harbin 150040, China
1 shared publication - Lei Tan
State Key Laboratory of Hydroscience and Engineering, Department of Energy and Power Engineering, Tsinghua University, Beijing, China
1 shared publication - Zhe Ma
State Key Laboratory of Hydroscience and Engineering, Department of Thermal Engineering, Tsinghua University, Beijing 100084, China
1 shared publication - Zijie Wang
Department of Thermal Engineering, State Key Laboratory of Hydro Science and Engineering, Tsinghua University, Beijing 100084, China
1 shared publication
Latest Publications
- 19 October 2017
- Published by ASME International in Journal of Fluids Engineering
- Vol. 140 (3)
Investigation on Flow Characteristics of Pump-Turbine Runners With Large Blade Lean
Frequent changes in the operating modes pose significant challenges in the development of a pump-turbine with high efficiency and stability. In this paper, two pump-turbine runners, one with a large positive blade lean and the other with a large negative lean, are investigated numerically and experimentally. These two runners are designed by using the optimum stacking condition at the high pressure edge (HPE). The experimental and the numerical results show that both runners have good efficiency performances, and pressure fluctuations for the runner with a negative blade lean are much lower than those for the runner with a positive blade lean. The internal flow field analyses clarify the effects of the blade lean on the pressure distribution around the runner blades. In the turbine mode at partial load, the negative blade lean can control flow separation in the high pressure side of the runner and then reduce the pressure fluctuations in the vaneless space.
- 19 October 2017
- Published by ASME International in Journal of Fluids Engineering
- Vol. 140 (3)
Investigation on Flow Characteristics of Pump-Turbine Runners With Large Blade Lean
Frequent changes in the operating modes pose significant challenges in the development of a pump-turbine with high efficiency and stability. In this paper, two pump-turbine runners, one with a large positive blade lean and the other with a large negative lean, are investigated numerically and experimentally. These two runners are designed by using the optimum stacking condition at the high pressure edge (HPE). The experimental and the numerical results show that both runners have good efficiency performances, and pressure fluctuations for the runner with a negative blade lean are much lower than those for the runner with a positive blade lean. The internal flow field analyses clarify the effects of the blade lean on the pressure distribution around the runner blades. In the turbine mode at partial load, the negative blade lean can control flow separation in the high pressure side of the runner and then reduce the pressure fluctuations in the vaneless space.
- Open Access
Pressure Fluctuations in the S-Shaped Region of a Reversible Pump-Turbine
Numerical simulations were performed to investigate pressure fluctuations in the S-shaped region of a pump-turbine model. Analyses focused on pressure fluctuations in the draft tube and in the gap between the guide vanes and runner. Calculations were made under six different operating conditions with a constant guide vane opening, and the best efficiency point, runaway point, and low-discharge point in the turbine brake zone were determined. The simulated results were compared with experimental measurements. In the draft tube, a twin vortex rope was observed. In the gap between the guide vanes and runner, a low frequency component was captured at both the runaway and low-discharge points in the turbine brake zone, which rotated at 65% of the runner frequency. This low frequency component was induced by the rotating stall phenomenon. At the runaway point, a single stall cell was found in the gap between the guide vanes and runner, while at the low-discharge point, four stall cells were observed.
Open AccessPressure Fluctuations in the S-Shaped Region of a Reversible Pump-Turbine
Numerical simulations were performed to investigate pressure fluctuations in the S-shaped region of a pump-turbine model. Analyses focused on pressure fluctuations in the draft tube and in the gap between the guide vanes and runner. Calculations were made under six different operating conditions with a constant guide vane opening, and the best efficiency point, runaway point, and low-discharge point in the turbine brake zone were determined. The simulated results were compared with experimental measurements. In the draft tube, a twin vortex rope was observed. In the gap between the guide vanes and runner, a low frequency component was captured at both the runaway and low-discharge points in the turbine brake zone, which rotated at 65% of the runner frequency. This low frequency component was induced by the rotating stall phenomenon. At the runaway point, a single stall cell was found in the gap between the guide vanes and runner, while at the low-discharge point, four stall cells were observed.