WSWagner Carvalho Santiago

Wagner Carvalho Santiago

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Wagner Carvalho Santiago has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Reuse of copper mining tailing as fine aggregate in high-performance concrete production

    by Yandra Beatriz de Oliveira Gonçalves, Wagner Carvalho Santiago, Rafael Akira Akisue

    The large volume of waste generated by copper ore beneficiation represents a major challenge in terms of disposal and management, particularly regarding environmental issues. In this context, the construction industry represents a promising alternative for utilizing this environmental liability. The aim of this study was to evaluate the feasibility of using copper ore waste in concrete production as a partial replacement for natural fine aggregate. In this research, fine aggregate was partially replaced with copper tailings at replacement levels of 10%, 20%, and 30%, in addition to a control mixture without waste. Additionally, a maximum water-cement ratio of 0.40 was adopted, and the slump was set at 120 ± 20 mm. Compressive strength was measured at 7 and 28 days of moist curing. The mixture design methodology used was developed by the Polytechnique School of University of São Paulo (EPUSP) and Institute of Technological Research (IPT). It was observed that the addition of waste caused a reduction in compressive strength, with the largest reduction being 13.53% at 28 days of curing for the mixture with a substitution content of 10%. The most favorable result observed in this study was for the mixture with a 20% replacement level. Not only did it minimize the reduction in compressive strength compared to the reference concrete, but also resulted in lower water absorption and void content.

  • Open Access

    Unreinforced concrete masonry under compression: Brazilian statistics, reliability analysis and code calibration

    by Wagner Carvalho Santiago, Tiago de Macedo Souza, Rafael Akira Akisue

    Although the new Brazilian code is considered an advancement, it still lacks a reliability-based calibration of partial safety factors. Therefore, this paper presents a comprehensive set of reliability analyses oriented to structural masonry members under compression in Brazil. This study was based on structural reliability theory, which allowed a safety assessment through the reliability index (β). Walls with hollow concrete blocks of three classes (A, B and C) and two modular sizes (M-15 and M-20), two ratios between the prism strength and the block compressive strength (η = 0.5 and 0.6), and three ratios between effective height and effective width (λ = 14, 19 and 24) were evaluated. Considering that each one of the 36 elements is described by five ratios between live and dead loads and the five ratios between wind and dead loads, 900 configurations were analyzed. Reliability procedures, the structural configurations and the calibration methodology were implemented and solved in the StRAnD – Structural Reliability Analysis and Design software. Results showed that the reliability indexes are greater for unreinforced masonry walls under compression with modular size M-20 than modular size M-15. It can be noted that the block compressive strength not only represents the greatest impact on the masonry’s safety level, but is also the most relevant random variable. Based on the reliability-based calibration of the Brazilian code, it is recommended that unreinforced masonry presents different partial safety factors (ɣm) than reinforced masonry. This work represents a stepping stone in evaluating the safety of Brazilian masonry structures, indicating a possible path in terms of achieving a more uniform reliability in masonry design.


  • Open Access

    FUZZY DISSOLVED OXYGEN CONTROLLER APPLIED IN ACTIVATED SLUDGE PROCESS

    by Hugo Adam Sábio, Wagner Carvalho Santiago, Ruy De Sousa Júnior, Maria Raquel Manhani, Rafael Akira Akisue

    Roughly 80% of waste water treatment plants are based on active sludge technique due to its simplicity and reliability. Under aerobic conditions microorganisms can grow on some organic pollutants present in the wastewater. As such, dissolved oxygen control is paramount in order to save energy, improve effluent quality and achieve high nitrogen removal. However, due to the nonlinearities of bioprocesses, dissolved oxygen (DO) is a challenge in terms of variable control. In Suzano municipal Waste Water Treatment Plant (WWTP) - located in São Paulo Metropolitan area - dissolved oxygen control is conducted based on a set of heuristic rules stablished by skilful operators. Although yielding satisfactory results, staff training is time consuming. Under the light of these facts, this study aimed to develop a fuzzy DO controller applied to activated sludge process. Data collection and implementation of the fuzzy control system were conducted in bioreactors at Suzano WWTP. Three fuzzy inference systems were developed: “aerator number”, “aerator speed” and “submergence height”. The fuzzy controller was tested and calibrated with a dynamic simulator and implemented as a supervisory controller, yielding positive results. Statistically, dissolved oxygen mean was 1.75 mg/L with a standard deviation of 0.25 mg/L. Based on the results the application of fuzzy logic for DO control in activated sludge process has proven not only viable, but an interesting control option. Fuzzy logic overcame DO non-linearities by translating an empirical knowledge into a linguistic, rule-based controller. It is a promising technique, bringing significant advances, both in treatment performance and energy efficiency.


  • Open Access

    Probabilistic models for live loads in buildings: critical review, comparison to Brazilian design standards and calibration of partial safety factors

    by Luis Gustavo Lopes Costa, Wagner Carvalho Santiago, André Teófilo Beck

    Nowadays, structural “limit state” design is made using characteristic or nominal values of actions, partial safety factors and load combination factors. The actual loading that a structure will be subjected to throughout its life is not known at the design phase. Yet, probabilistic models of such loadings are useful for the rational determination of partial safety factors and load combination factors. The probabilistic model leading to nominal live loads of NBR 6120:2019 (Design Loads for Structures) has never been openly discussed. Herein a simple probabilistic model describing spatial and temporal variabilities of live loads in buildings is presented and discussed. The model is built as a sum of two stochastic processes representing the sustained and intermittent parts of the live load. Model parameters are the ones recommended by the Joint Committee on Structural Safety (JCSS), based on extensive surveys done in several countries. By way of Monte Carlo simulations, sample values of live load actions are obtained for buildings of different occupancy types. These values are compared with those recommended by international standards, and those recommended in NBR 6120:2019 and NBR 8681:2003 (Actions and Safety of Structures). The corresponding statistics for the fifty-year extreme and arbitrary point-in-time distributions of live loads are presented; these statistics are very relevant for reliability analyses and for reliability-based code calibration. The stochastic live load model is also employed in a reliability-based calibration to obtain partial safety factors and load combination factors to be used in Brazilian design codes, for ultimate and serviceability limit state verifications.


  • Open Access

    Reliability-based calibration of main Brazilian structural design codes

    by Wagner Carvalho Santiago, Henrique Machado Kroetz, Sérgio Hampshire de C. Santos, Fernando Rebouças Stucchi, André Teófilo Beck

    Structural reliability theory has long been recognized as the proper tool to guide selection of partial safety factors in limit state structural design codes. Brazilian design codes, however, have never been through this calibration process. This paper addresses the reliability-based calibration of partial safety factors of Brazilian design codes for loads (NBR8681:2003), and for steel (NBR8800:2008) and concrete (NBR6118:2014) structures. The study is based on an extensive dataset of load and strength variables, addressing the Brazilian reality, as much as possible. Calibration minimizes the variations of reliability indexes of the most diverse structures designed according to the codes of interest, with regard to a target reliability index chosen by the analyst. The main result of calibration is to make reliability indexes more uniform, for different design configurations. In case of Brazilian codes, this could be achieved by increasing main variable loads, and reducing the combination values of secondary loads. This paper presents results that are not (yet) recommended for adoption in Brazilian codes, but which should be discussed with the community in order to reach minimal consensus.


  • Open Access

    Reliability-based calibration of Brazilian structural design codes used in the design of concrete structures

    by W. C. Santiago, H. M. Kroetz, A. T. Beck

    This paper presents a reliability-based calibration of partial safety factors for Brazilian codes used in the design of concrete structures. The work is based on reliability theory, which allows an explicit representation of the uncertainties involved in terms of resistances and loads. Regarding the resistances, this study considers beams with concrete of five classes (C20, C30, C40, C50 and C60), three ratios between base and effective depth (0.25, 0.50 and 0.75), three longitudinal reinforcement ratios (ρmin, 0.5% and ρmax) and three transverse reinforcement ratios ( A s s m i n, 5 . A s s m i n and A s s m a x). In terms of loads, this work considers seven ratios between live loads and permanent loads (qn/gn), and seven ratios between wind loads and permanent loads (wn/gn). The study also adopts a single value for the target reliability index (βtarget = 3.0). Results show that the optimized set of partial safety factors leads to more uniform reliability for different design situations and load combinations.


  • Open Access

    Study of brazilian structural concrete block conformity

    by W. C. Santiago, A. T. Beck

    This paper presents a study of the conformity of structural concrete blocks manufactured and used in masonry construction in Brazil. It is based on compressive strength tests, on dimensional analysis and absorption tests of over six thousand samples from three classes (A, B and C) and two modular sizes (M-15 and M-20). National results show that blocks tend to have an estimated compressive strength higher than specified, except blocks from class A. Regional results show that blocks manufactured in the northeast (NE) are consistently non-conforming, for all block classes. The study also shows that dimensional variations and absorption tests results are within code tolerances.


  • Open Access

    A new study of Brazilian concrete strength conformance

    by W.C. Santiago, A.T. Beck

    This paper presents a new evaluation of the strength compliance of concretes produced in Brazil. It is based on experimental results of over twenty-seven thousand concrete samples from different parts of the country. Results show that a significant part of Brazilian concrete do not reach the characteristic strength (fck) specified in design, and the percentage of nonconforming samples tend to be higher than 5%. This study also reveals the concrete produced in the South and Midwest regions have less variability than the ones produced in the other regions of the country. These results emphasize the importance of a rigorous control in manufacturing and reception of concretes in order to reduce the nonconforming cases.