Ke Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ke Zhang has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Jiang Lei
Xi'an Jiaotong University State Key Laboratory for Strength and Vibration of Mechanical Structures, School of Aerospace Engineering Xi’an, Shannxi 710049 , China
8 shared publications - Jingtian Duan
Xi'an Jiaotong University State Key Laboratory for Strength and Vibration of Mechanical Structures, School of Aerospace Engineering Xi’an, Shannxi 710049 , China
4 shared publications - Junmei Wu
School of Aerospace, Xi’an Jiaotong University, No. 28, Xianning West Road, Beilin County, Xi’an 710049, China
4 shared publications - Jiaxu Yao
Xi’an Jiaotong University State Key Laboratory for Strength and Vibration of Mechanical Structures Xi’an, Shaanxi 710049 , China
3 shared publications - Jin Xu
Xi'an Jiaotong University State Key Laboratory for Strength and Vibration of Mechanical Structures, School of Aerospace Engineering Xi’an, Shannxi 710049 , China
3 shared publications - Jin Xu
School of Civil Engineering Yantai University 30 Qingquan Road Yantai 264005 China
3 shared publications
Latest Publications
- 18 October 2023
- Published by ASME International in ASME Journal of Heat and Mass Transfer
- Vol. 145 (12) , 1-37
Comparisons of Overall Performance Among Double-Jet Film Cooling Holes, Cylinder Holes, and Fan-Shaped Holes
In this paper, the film-cooling effectiveness (η) and heat transfer coefficient (h) of different film hole geometries are investigated, including double-jet film cooling (DJFC) holes, streamwise cylindrical holes, and fan-shaped holes, both experimentally and numerically. Results reveal that when the blowing ratio is less than 1.0, the DJFC holes have the highest η and the highest h, as well as the highest net heat flux reduction (NHFR). However, a higher blowing ratio (>1.0) leads to a quickly decreasing NHFR of DJFC holes. The asymmetric antikidney vortex and the high turbulent kinetic energy (TKE) are dominant in the performance of the DJFC holes. Owing to medium effectiveness and the lowest heat transfer coefficient, the fan-shaped holes possess the highest net heat flux reduction at M = 2.0 although the value is negative. The relatively weak kidney vortex and the low TKE can explain the phenomena. The cylindrical holes have the lowest η and the lowest NHFR due to the kidney vortex and relatively higher TKE.
- 18 October 2023
- Published by ASME International in ASME Journal of Heat and Mass Transfer
- Vol. 145 (12) , 1-37
Comparisons of Overall Performance Among Double-Jet Film Cooling Holes, Cylinder Holes, and Fan-Shaped Holes
In this paper, the film-cooling effectiveness (η) and heat transfer coefficient (h) of different film hole geometries are investigated, including double-jet film cooling (DJFC) holes, streamwise cylindrical holes, and fan-shaped holes, both experimentally and numerically. Results reveal that when the blowing ratio is less than 1.0, the DJFC holes have the highest η and the highest h, as well as the highest net heat flux reduction (NHFR). However, a higher blowing ratio (>1.0) leads to a quickly decreasing NHFR of DJFC holes. The asymmetric antikidney vortex and the high turbulent kinetic energy (TKE) are dominant in the performance of the DJFC holes. Owing to medium effectiveness and the lowest heat transfer coefficient, the fan-shaped holes possess the highest net heat flux reduction at M = 2.0 although the value is negative. The relatively weak kidney vortex and the low TKE can explain the phenomena. The cylindrical holes have the lowest η and the lowest NHFR due to the kidney vortex and relatively higher TKE.
- 9 October 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (12) , 1-44
Investigation on Heat Transfer Distribution of Rotating Two-Pass Smooth and Ribbed Channels Under Aero-Engine Simulated Conditions
Rotating significantly alters the internal cooling of turbine rotor blades by induced Coriolis force and buoyancy force, whose effects are characterized by the nondimensional rotation number (Ro) and buoyancy parameter (Bo). The present work was carried out in a new experimental rig of rotor blade internal cooling to obtain detailed heat transfer distributions when the three nondimensional criterion numbers (i.e., Re, Ro, and Bo) are similar to aero-engine operating conditions. Smooth and ribbed two-pass internal cooling channels with a 180-deg tip turn are investigated. The hydraulic diameter is 25.4 mm (1 in.), and the aspect ratio is 2:1. The Reynolds number is fixed at 25,000, with the maximum Ro and Bo of 0.316 and 0.272, respectively. The steady-state thermochromic liquid crystal (TLC) technique is used to measure detailed heat transfer distributions in the channel. Steady-state RANS simulations are also employed to resolve the flow characteristics. The effects of rotation on the flow and heat transfer characteristics are studied in this paper. The results show effects of rotation on the heat transfer distribution present apparent spatial discrepancy, especially around the bend region. The significant difference in the influence of rotation is witnessed in the smooth and the ribbed channels.
- 9 October 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (12) , 1-44
Investigation on Heat Transfer Distribution of Rotating Two-Pass Smooth and Ribbed Channels Under Aero-Engine Simulated Conditions
Rotating significantly alters the internal cooling of turbine rotor blades by induced Coriolis force and buoyancy force, whose effects are characterized by the nondimensional rotation number (Ro) and buoyancy parameter (Bo). The present work was carried out in a new experimental rig of rotor blade internal cooling to obtain detailed heat transfer distributions when the three nondimensional criterion numbers (i.e., Re, Ro, and Bo) are similar to aero-engine operating conditions. Smooth and ribbed two-pass internal cooling channels with a 180-deg tip turn are investigated. The hydraulic diameter is 25.4 mm (1 in.), and the aspect ratio is 2:1. The Reynolds number is fixed at 25,000, with the maximum Ro and Bo of 0.316 and 0.272, respectively. The steady-state thermochromic liquid crystal (TLC) technique is used to measure detailed heat transfer distributions in the channel. Steady-state RANS simulations are also employed to resolve the flow characteristics. The effects of rotation on the flow and heat transfer characteristics are studied in this paper. The results show effects of rotation on the heat transfer distribution present apparent spatial discrepancy, especially around the bend region. The significant difference in the influence of rotation is witnessed in the smooth and the ribbed channels.
- 22 May 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (9) , 1-24
Investigation on Flow Characteristics and Its Effect on Heat Transfer Enhancement in a Wide Channel With Staggered Diamond-S Pin Fins
Flow statistic in the mid-plane of a rectangular channel with diamond-s pin fins was obtained by means of particle imaging velocimetry at Re = 10,000. Large-scale and small-scale fluctuations were separated using proper orthogonal decomposition. The flow characteristics were compared to the Nusselt number distribution on the endwall acquired by thermochromic liquid crystal to reveal the flow mechanism driving heat transfer enhancement. Results indicate that local vorticity plays an important role in strengthening Nu on both sides of leading point (Zone 1). Downstream of the two sharp edges on both sides (Zone 2), small size disturbances from shear layer eddies drive local heat transfer. The flow characteristics and heat transfer distribution downstream of the first row (Zone 3) present alternated feature along Y direction due to the interaction between shear layers of neighboring pin fins. Lateral velocity fluctuation induced by large vortex shedding drives the heat transfer augmentation in Zone 3 where there is violent large vortex shedding. Meanwhile, small size disturbances of the shear layer drive local heat transfer enhancement in Zone 3 downstream of pin fins where large vortex shedding is suppressed. For the second and third rows, there is no difference in the flow characteristics downstream of neighboring pin fins. Small-size fluctuations distributed uniformly downstream of large vortex shedding (Zone 4) resulting in a uniformly distributed Nu.
- 22 May 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (9) , 1-24
Investigation on Flow Characteristics and Its Effect on Heat Transfer Enhancement in a Wide Channel With Staggered Diamond-S Pin Fins
Flow statistic in the mid-plane of a rectangular channel with diamond-s pin fins was obtained by means of particle imaging velocimetry at Re = 10,000. Large-scale and small-scale fluctuations were separated using proper orthogonal decomposition. The flow characteristics were compared to the Nusselt number distribution on the endwall acquired by thermochromic liquid crystal to reveal the flow mechanism driving heat transfer enhancement. Results indicate that local vorticity plays an important role in strengthening Nu on both sides of leading point (Zone 1). Downstream of the two sharp edges on both sides (Zone 2), small size disturbances from shear layer eddies drive local heat transfer. The flow characteristics and heat transfer distribution downstream of the first row (Zone 3) present alternated feature along Y direction due to the interaction between shear layers of neighboring pin fins. Lateral velocity fluctuation induced by large vortex shedding drives the heat transfer augmentation in Zone 3 where there is violent large vortex shedding. Meanwhile, small size disturbances of the shear layer drive local heat transfer enhancement in Zone 3 downstream of pin fins where large vortex shedding is suppressed. For the second and third rows, there is no difference in the flow characteristics downstream of neighboring pin fins. Small-size fluctuations distributed uniformly downstream of large vortex shedding (Zone 4) resulting in a uniformly distributed Nu.
- 27 May 2022
- Published by Wiley in Journal of Turbomachinery
- Vol. 144 (7)
Investigation on the Contribution of Large-Scale Fluctuation and Small-Scale Disturbance of Coolant to Heat Transfer Enhancement in a Rectangular Channel With Pin Fins
The flow field in a channel with staggered pin-fin array was measured using time-resolved Particle Imaging Velocimetry (PIV). The distributions of flow field statistics were compared with those of Nusselt number on the endwall measured by thermochromic liquid crystal (TLC) of the same geometry. Lower-order large-scale fluctuation and higher order small-scale disturbances were examined separately using Proper Orthogonal Decomposition (POD) to study the flow field characteristics and their individual effect on the heat transfer enhancement. Pin fins with circular and square cross-section geometries were studied at Reynolds numbers of 10,000 and 20,000. Results indicate that for circular pin fins, the distribution of lateral/transverse velocity fluctuations or turbulent kinetic energy from large-scale vortex shedding resembles that of local Nu, and the heat transfer augmentation downstream of the recirculation zone is dominant, while the heat transfer enhancement is limited in the shear layer on both sides of recirculation where disturbances are small scale. However, for square pin fins, heat transfer augmentation in the shear layer is as strong as that downstream of recirculation, while large-scale fluctuations downstream is much weaker than small scale disturbances in the shear layer. Compared to small-scale disturbances, large-scale fluctuations are found to contribute more efficiently to endwall heat transfer enhancement both for circular and for square pin fins. Large-scale fluctuation, as well as heat transfer enhancement, weakens with the increase in Reynolds number, while smaller-scale disturbance grows stronger at the same time.
- 27 May 2022
- Published by Wiley in Journal of Turbomachinery
- Vol. 144 (7)
Investigation on the Contribution of Large-Scale Fluctuation and Small-Scale Disturbance of Coolant to Heat Transfer Enhancement in a Rectangular Channel With Pin Fins
The flow field in a channel with staggered pin-fin array was measured using time-resolved Particle Imaging Velocimetry (PIV). The distributions of flow field statistics were compared with those of Nusselt number on the endwall measured by thermochromic liquid crystal (TLC) of the same geometry. Lower-order large-scale fluctuation and higher order small-scale disturbances were examined separately using Proper Orthogonal Decomposition (POD) to study the flow field characteristics and their individual effect on the heat transfer enhancement. Pin fins with circular and square cross-section geometries were studied at Reynolds numbers of 10,000 and 20,000. Results indicate that for circular pin fins, the distribution of lateral/transverse velocity fluctuations or turbulent kinetic energy from large-scale vortex shedding resembles that of local Nu, and the heat transfer augmentation downstream of the recirculation zone is dominant, while the heat transfer enhancement is limited in the shear layer on both sides of recirculation where disturbances are small scale. However, for square pin fins, heat transfer augmentation in the shear layer is as strong as that downstream of recirculation, while large-scale fluctuations downstream is much weaker than small scale disturbances in the shear layer. Compared to small-scale disturbances, large-scale fluctuations are found to contribute more efficiently to endwall heat transfer enhancement both for circular and for square pin fins. Large-scale fluctuation, as well as heat transfer enhancement, weakens with the increase in Reynolds number, while smaller-scale disturbance grows stronger at the same time.
- Open Access
Systematic Comparison on Convective Heat Transfer Characteristics of Several Pin Fins for Turbine Cooling
This paper is focused on the heat transfer augment ability and friction factor of different cross-section pin fins. An experimental study is conducted in a wide rectangular channel. The steady-state thermochromic liquid crystals (TLC) method is applied to measure the tested surface temperature. Nine sets of pin fins are employed in the experiment. The nominal diameter of all pin fins is the same value. Nine sets of pin fins have three roundness shapes (Circle, Ellipse and Oblong), three streamline shapes (Dropform, NACA and Lancet) and three quadrangle shapes (Diamond, Diamond-s and Square), respectively. The arrangement parameters of all nine shapes are kept the same. As they have the same nominal diameter and arrangement, the channel blockage ratio is the same for each pin fin set. Reynolds numbers range from 10,000 to 60,000. The pressure losses of pin fin arrays are measured to obtain friction factor. Meanwhile, the overall thermal performances of all nine sets are also considered and compared. The results show heat transfer enhancement abilities of quadrangle shape pin fins are relatively higher than the roundness and streamline shapes. Diamond-s pin fins present the largest averaged Nusselt number and overall thermal performance on the endwall for all the nine pin fins under different Re. Concerning overall thermal performance, the traditional Circle pin fin is the second best. The pressure loss of streamline shape pin fins is the lowest in these three shape types. Moreover, the characteristic of local heat transfer distribution varies substantially for different pin shapes at low Re.
Open AccessSystematic Comparison on Convective Heat Transfer Characteristics of Several Pin Fins for Turbine Cooling
This paper is focused on the heat transfer augment ability and friction factor of different cross-section pin fins. An experimental study is conducted in a wide rectangular channel. The steady-state thermochromic liquid crystals (TLC) method is applied to measure the tested surface temperature. Nine sets of pin fins are employed in the experiment. The nominal diameter of all pin fins is the same value. Nine sets of pin fins have three roundness shapes (Circle, Ellipse and Oblong), three streamline shapes (Dropform, NACA and Lancet) and three quadrangle shapes (Diamond, Diamond-s and Square), respectively. The arrangement parameters of all nine shapes are kept the same. As they have the same nominal diameter and arrangement, the channel blockage ratio is the same for each pin fin set. Reynolds numbers range from 10,000 to 60,000. The pressure losses of pin fin arrays are measured to obtain friction factor. Meanwhile, the overall thermal performances of all nine sets are also considered and compared. The results show heat transfer enhancement abilities of quadrangle shape pin fins are relatively higher than the roundness and streamline shapes. Diamond-s pin fins present the largest averaged Nusselt number and overall thermal performance on the endwall for all the nine pin fins under different Re. Concerning overall thermal performance, the traditional Circle pin fin is the second best. The pressure loss of streamline shape pin fins is the lowest in these three shape types. Moreover, the characteristic of local heat transfer distribution varies substantially for different pin shapes at low Re.
- Open Access
- 16 July 2021
- Published by ASME International
The Flow Field Characteristic Correlated With Heat Transfer Performance in a Wide Channel With Staggered Circular Pin Fins
The velocity field in a wide rectangular channel (*AR*=4) with staggered circular pin fin array was measured using Particle Image Velocimetry (PIV). The cylinder pin fin has a diameter of 8 mm and height to diameter ratio (*H/D*) of 3. The streamwise pitch (*X/D*) and spanwise pitch (*S/D*) of pin fins are 4.5 and 2 respectively. The experiment was conducted at two Reynolds number,
- 16 July 2021
- Published by ASME International
Open AccessThe Flow Field Characteristic Correlated With Heat Transfer Performance in a Wide Channel With Staggered Circular Pin Fins
The velocity field in a wide rectangular channel (*AR*=4) with staggered circular pin fin array was measured using Particle Image Velocimetry (PIV). The cylinder pin fin has a diameter of 8 mm and height to diameter ratio (*H/D*) of 3. The streamwise pitch (*X/D*) and spanwise pitch (*S/D*) of pin fins are 4.5 and 2 respectively. The experiment was conducted at two Reynolds number,
- 22 January 2019
- Published by Wiley in Journal of Turbomachinery
- Vol. 141 (5)
Effect of Density Ratio on Film-Cooling Effectiveness Distribution and Its Uniformity for Several Hole Geometries on a Flat Plate
The film cooling effectiveness distribution and its uniformity downstream of a row of film cooling holes on a flat plate are investigated by pressure sensitive paint (PSP) under different density ratios. Several hole geometries are studied, including streamwise cylindrical holes, compound-angled cylindrical holes, streamwise fan-shape holes, compound-angled fan-shape holes, and double-jet film-cooling (DJFC) holes. All of them have an inclination angle (θ) of 35 deg. The compound angle (β) is 45 deg. The fan-shape holes have a 10 deg expansion in the spanwise direction. For a fair comparison, the pitch is kept as 4d for the cylindrical and the fan-shape holes, and 8d for the DJFC holes. The uniformity of effectiveness distribution is described by a new parameter (Lateral-Uniformity, LU) defined in this paper. The effects of density ratios (DR = 1.0, 1.5 and 2.5) on the film-cooling effectiveness and its uniformity are focused. Differences among geometries and effects of blowing ratios (M = 0.5, 1.0, 1.5, and 2.0) are also considered. The results show that at higher density ratios, the lateral spread of the discrete-hole geometries (i.e., the cylindrical and the fan-shape holes) is enhanced, while the DJFC holes is more advantageous in film-cooling effectiveness. Mostly, a higher lateral-uniformity is obtained at DR = 2.5 due to better coolant coverage and enhanced lateral spread, but the effects of the density ratio on the lateral-uniformity are not monotonic in some cases. Utilizing the compound angle configuration leads to an increased lateral-uniformity due to a stronger spanwise motion of the jet. Generally, with a higher blowing ratio, the lateral-uniformity of the discrete-hole geometries decreases due to narrower traces, while that of the DJFC holes increases due to a stronger spanwise movement.
- 22 January 2019
- Published by Wiley in Journal of Turbomachinery
- Vol. 141 (5)
Effect of Density Ratio on Film-Cooling Effectiveness Distribution and Its Uniformity for Several Hole Geometries on a Flat Plate
The film cooling effectiveness distribution and its uniformity downstream of a row of film cooling holes on a flat plate are investigated by pressure sensitive paint (PSP) under different density ratios. Several hole geometries are studied, including streamwise cylindrical holes, compound-angled cylindrical holes, streamwise fan-shape holes, compound-angled fan-shape holes, and double-jet film-cooling (DJFC) holes. All of them have an inclination angle (θ) of 35 deg. The compound angle (β) is 45 deg. The fan-shape holes have a 10 deg expansion in the spanwise direction. For a fair comparison, the pitch is kept as 4d for the cylindrical and the fan-shape holes, and 8d for the DJFC holes. The uniformity of effectiveness distribution is described by a new parameter (Lateral-Uniformity, LU) defined in this paper. The effects of density ratios (DR = 1.0, 1.5 and 2.5) on the film-cooling effectiveness and its uniformity are focused. Differences among geometries and effects of blowing ratios (M = 0.5, 1.0, 1.5, and 2.0) are also considered. The results show that at higher density ratios, the lateral spread of the discrete-hole geometries (i.e., the cylindrical and the fan-shape holes) is enhanced, while the DJFC holes is more advantageous in film-cooling effectiveness. Mostly, a higher lateral-uniformity is obtained at DR = 2.5 due to better coolant coverage and enhanced lateral spread, but the effects of the density ratio on the lateral-uniformity are not monotonic in some cases. Utilizing the compound angle configuration leads to an increased lateral-uniformity due to a stronger spanwise motion of the jet. Generally, with a higher blowing ratio, the lateral-uniformity of the discrete-hole geometries decreases due to narrower traces, while that of the DJFC holes increases due to a stronger spanwise movement.
- 28 November 2018
- Published by Wiley in Journal of Turbomachinery
- Vol. 140 (12)
Interaction of Flow and Film-Cooling Effectiveness Between Double-Jet Film-Cooling Holes With Various Spanwise Distances
The interaction of flow and film-cooling effectiveness between jets of double-jet film-cooling (DJFC) holes on a flat plate is studied experimentally. The time-averaged flow field in several axial positions (X/d = −2.0, 1.0, and 5.0) is obtained through a seven-hole probe. The downstream film-cooling effectiveness on the flat plate is measured by pressure sensitive paint (PSP). The inclination angle (θ) of all the holes is 35 deg, and the compound angle (β) is ±45 deg. Effects of the spanwise distance (p = 0, 0.5d, 1.0d, 1.5d, and 2.0d) between the two interacting jets of DJFC holes are studied, while the streamwise distance (s) is kept as 3d. The blowing ratio (M) varies as 0.5, 1.0, 1.5, and 2.0. The density ratio (DR) is maintained at 1.0. Results show that the interaction between the two jets of DJFC holes has different effects at different spanwise distances. For a small spanwise distance (p/d = 0), the interaction between the jets presents a pressing effect. The downstream jet is pressed down and kept attached to the surface by the upstream one. The effectiveness is not sensitive to blowing ratios. For mid-spanwise distances (p/d = 0.5 and 1.0), the antikidney vortex pair dominates the interaction and pushes both of the jets down, thus leading to better coolant coverage and higher effectiveness. As the spanwise distance becomes larger (p/d ≥ 1.5), the pressing effect almost disappears, and the antikidney vortex pair effect is weaker. The jets separate from each other and the coolant coverage decreases. At a higher blowing ratio, the interaction between the jets of DJFC holes happens later.
- 28 November 2018
- Published by Wiley in Journal of Turbomachinery
- Vol. 140 (12)
Interaction of Flow and Film-Cooling Effectiveness Between Double-Jet Film-Cooling Holes With Various Spanwise Distances
The interaction of flow and film-cooling effectiveness between jets of double-jet film-cooling (DJFC) holes on a flat plate is studied experimentally. The time-averaged flow field in several axial positions (X/d = −2.0, 1.0, and 5.0) is obtained through a seven-hole probe. The downstream film-cooling effectiveness on the flat plate is measured by pressure sensitive paint (PSP). The inclination angle (θ) of all the holes is 35 deg, and the compound angle (β) is ±45 deg. Effects of the spanwise distance (p = 0, 0.5d, 1.0d, 1.5d, and 2.0d) between the two interacting jets of DJFC holes are studied, while the streamwise distance (s) is kept as 3d. The blowing ratio (M) varies as 0.5, 1.0, 1.5, and 2.0. The density ratio (DR) is maintained at 1.0. Results show that the interaction between the two jets of DJFC holes has different effects at different spanwise distances. For a small spanwise distance (p/d = 0), the interaction between the jets presents a pressing effect. The downstream jet is pressed down and kept attached to the surface by the upstream one. The effectiveness is not sensitive to blowing ratios. For mid-spanwise distances (p/d = 0.5 and 1.0), the antikidney vortex pair dominates the interaction and pushes both of the jets down, thus leading to better coolant coverage and higher effectiveness. As the spanwise distance becomes larger (p/d ≥ 1.5), the pressing effect almost disappears, and the antikidney vortex pair effect is weaker. The jets separate from each other and the coolant coverage decreases. At a higher blowing ratio, the interaction between the jets of DJFC holes happens later.
- 2 August 2017
- Published by Springer Nature in Experiments in Fluids
- Vol. 58 (9) , 109
The three-dimensional characteristics of the unsteady wall-pressure in a low-Mach-number rectangular cavity flow with Rossiter model oscillation
- 2 August 2017
- Published by Springer Nature in Experiments in Fluids
- Vol. 58 (9) , 109
The three-dimensional characteristics of the unsteady wall-pressure in a low-Mach-number rectangular cavity flow with Rossiter model oscillation