Hongsheng Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hongsheng Zhang has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Yue Wang
Harbin Institute of Technology
3 shared publications Xiangxiang Wang
Harbin Institute of Technology
2 shared publications- Jun Pan
Zhejiang Sci-Tech University
1 shared publication - Li Shuo
School of Mechatronics Engineering, Harbin Institute of Technology, Harbin, China
1 shared publication - Meng Rao
Department of Mechanical Engineering, Tsinghua University, Beijing, China
1 shared publication Nianli Lu
Harbin Institute of Technology
1 shared publication
Latest Publications
- 7 September 2026
- Published by Taylor & Francis in Engineering Optimization
- p. 1-26
A novel design method based on proportional periodic topology optimization and its application in box metal structures
1. Topology optimization is an optimization method based on size optimization and shape optimization, by determining the connectivity, location and shape of voids within a given design domain (Deat...
- 7 September 2026
- Published by Taylor & Francis in Engineering Optimization
- p. 1-26
A novel design method based on proportional periodic topology optimization and its application in box metal structures
1. Topology optimization is an optimization method based on size optimization and shape optimization, by determining the connectivity, location and shape of voids within a given design domain (Deat...
- Open Access
- 1 October 2025
- Published by Springer Nature
- p. 717-727
ANSYS Contact Simulation Analysis Between Shed Tunnel Structure and Ultra-High Voltage Wire
- 1 October 2025
- Published by Springer Nature
- p. 717-727
Open AccessANSYS Contact Simulation Analysis Between Shed Tunnel Structure and Ultra-High Voltage Wire
- 14 August 2025
- Published by Springer Nature in Acta Mechanica
- Vol. 236 (10) , 6323-6338
Absolute nodal coordinate formulation beam element with arbitrary cross-section based on Monte Carlo integration
- 14 August 2025
- Published by Springer Nature in Acta Mechanica
- Vol. 236 (10) , 6323-6338
Absolute nodal coordinate formulation beam element with arbitrary cross-section based on Monte Carlo integration
- Open Access
- 29 June 2024
- Published by Springer Nature
- p. 461-475
Research on Equivalent Wind Load Spectrum Acquisition and Remaining Fatigue Strength Method of Double Active Arm Type Holding Pole
In order to study the wind load fatigue residual strength in in-service holding poles for preventing disasters, and improving load-bearing capacity reliability. Firstly, using the Davenport wind speed spectrum to simulate the wind speed, it will be the input load of the finite element dynamics model of the 2 × 40 kN double active arm type holding pole (DAATHP). The stress time history curve at the welding section of the main chord at the bottom of the tower shaft is obtained at the working condition with the wind angle of 0°, 45°, 90°, and 135°. The rain flow counting method derives the statistical characteristics of the mean, amplitude, and frequency of stress at four wind angles. Secondly, the frequency of wind load under four wind angles is extended, and the synthesized fatigue load spectrum is used as the equivalent wind load spectrum. Finally, the Paris-Eadogan equation is used to derive the calculation formula of fatigue residual strength of the main chord at the bottom of the tower shaft, and the functional function of the main chord is established and then the failure probability formula is derived by combining the equivalent wind load spectrum. It is found that, compared with the ANSYS calculation results, the error of the predicted stress spectrum of the proposed method is minor, only 7.95%. It is verified that the proposed method can efficiently obtain the equivalent load spectrum of the DAATHP. The results indicate that it is feasible and practical to apply the proposed method to calculate the remaining fatigue life of the DAATHP.
- 29 June 2024
- Published by Springer Nature
- p. 461-475
Open AccessResearch on Equivalent Wind Load Spectrum Acquisition and Remaining Fatigue Strength Method of Double Active Arm Type Holding Pole
In order to study the wind load fatigue residual strength in in-service holding poles for preventing disasters, and improving load-bearing capacity reliability. Firstly, using the Davenport wind speed spectrum to simulate the wind speed, it will be the input load of the finite element dynamics model of the 2 × 40 kN double active arm type holding pole (DAATHP). The stress time history curve at the welding section of the main chord at the bottom of the tower shaft is obtained at the working condition with the wind angle of 0°, 45°, 90°, and 135°. The rain flow counting method derives the statistical characteristics of the mean, amplitude, and frequency of stress at four wind angles. Secondly, the frequency of wind load under four wind angles is extended, and the synthesized fatigue load spectrum is used as the equivalent wind load spectrum. Finally, the Paris-Eadogan equation is used to derive the calculation formula of fatigue residual strength of the main chord at the bottom of the tower shaft, and the functional function of the main chord is established and then the failure probability formula is derived by combining the equivalent wind load spectrum. It is found that, compared with the ANSYS calculation results, the error of the predicted stress spectrum of the proposed method is minor, only 7.95%. It is verified that the proposed method can efficiently obtain the equivalent load spectrum of the DAATHP. The results indicate that it is feasible and practical to apply the proposed method to calculate the remaining fatigue life of the DAATHP.
- Open Access
- 29 June 2024
- Published by Springer Nature
- p. 73-85
Research on Dynamic Simulation of Crane Movable Pulley System with Defects
The movable pulley block failure can lead to catastrophic crane accidents, so the dynamic performance of a defective movable pulley block system is essential. Based on ANSYS contact analysis through APDL command, a pulley block simulation platform is developed, which can be used for dynamic analysis of defective pulley systems. Firstly, a parameterized 2D contact model is established and validated through static analysis. Then, dynamic simulation analysis for the intact pulley block under two working conditions is performed: lifting from the ground and sudden unloading. Finally, COMBIN 37 is used as a defective element, and dynamic simulations are analyzed for the faulty pulley system with hook or wire rope rupture. The analysis results show that the longer the unloading time and the shorter the wire rope length will lead to a minor impact under hook rupture and sudden unloading conditions. Meanwhile, if the unloading time is consistent, the dynamic analysis of the intact pulley block under sudden unloading and defective pulley block with hook rupture are equivalent. It is worth noting that when the steel wire ropes on both sides of the moving pulley break simultaneously in a defective system, it will cause a more significant horizontal impact force. This study demonstrates that ANSYS contact analysis with COMBIN 37 as the defective element can accurately and efficiently apply the dynamic simulation of a crane movable pulley system with defects.
- 29 June 2024
- Published by Springer Nature
- p. 73-85
Open AccessResearch on Dynamic Simulation of Crane Movable Pulley System with Defects
The movable pulley block failure can lead to catastrophic crane accidents, so the dynamic performance of a defective movable pulley block system is essential. Based on ANSYS contact analysis through APDL command, a pulley block simulation platform is developed, which can be used for dynamic analysis of defective pulley systems. Firstly, a parameterized 2D contact model is established and validated through static analysis. Then, dynamic simulation analysis for the intact pulley block under two working conditions is performed: lifting from the ground and sudden unloading. Finally, COMBIN 37 is used as a defective element, and dynamic simulations are analyzed for the faulty pulley system with hook or wire rope rupture. The analysis results show that the longer the unloading time and the shorter the wire rope length will lead to a minor impact under hook rupture and sudden unloading conditions. Meanwhile, if the unloading time is consistent, the dynamic analysis of the intact pulley block under sudden unloading and defective pulley block with hook rupture are equivalent. It is worth noting that when the steel wire ropes on both sides of the moving pulley break simultaneously in a defective system, it will cause a more significant horizontal impact force. This study demonstrates that ANSYS contact analysis with COMBIN 37 as the defective element can accurately and efficiently apply the dynamic simulation of a crane movable pulley system with defects.
- Open Access
- 27 March 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (7) , 2292
A Detailed Investigation of Gear Body-Induced Tooth Deflections and Development of an Improved Analytical Solution
Many researchers have developed analytical methods to evaluate gear meshing stiffness. Some of these methods ignored the effect of the gear body while others used a simplified model to consider its effect. Until now, a detailed investigation of gear body-induced tooth deflections has been rare, especially for the double-tooth-pair meshing period. In this study, we present a detailed investigation of gear body-induced tooth deflections. To be specific, we will discuss how to accurately evaluate gear body-induced tooth deflections using the finite element analysis, and what are the effect of parameters such as loading and gear parameters on gear body-induced tooth deflections. Then, an improved solution is developed for evaluating the body-induced tooth deflection. In the single-tooth-pair meshing period, the improved formula is developed based on a popular formula proposed by Sainsot and Velex. This is achieved by optimizing the coefficients used in their formula to make the formula more accurate to evaluate gear body-induced tooth deflections. Meanwhile, we introduce a new term called affiliated body stiffness to evaluate the body-induced tooth deflections in the double-tooth-pair meshing period. The improved method can give higher accuracy in evaluating gear body-induced tooth deflections of spur gears with a pressure angle of 20°.
- 27 March 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (7) , 2292
Open AccessA Detailed Investigation of Gear Body-Induced Tooth Deflections and Development of an Improved Analytical Solution
Many researchers have developed analytical methods to evaluate gear meshing stiffness. Some of these methods ignored the effect of the gear body while others used a simplified model to consider its effect. Until now, a detailed investigation of gear body-induced tooth deflections has been rare, especially for the double-tooth-pair meshing period. In this study, we present a detailed investigation of gear body-induced tooth deflections. To be specific, we will discuss how to accurately evaluate gear body-induced tooth deflections using the finite element analysis, and what are the effect of parameters such as loading and gear parameters on gear body-induced tooth deflections. Then, an improved solution is developed for evaluating the body-induced tooth deflection. In the single-tooth-pair meshing period, the improved formula is developed based on a popular formula proposed by Sainsot and Velex. This is achieved by optimizing the coefficients used in their formula to make the formula more accurate to evaluate gear body-induced tooth deflections. Meanwhile, we introduce a new term called affiliated body stiffness to evaluate the body-induced tooth deflections in the double-tooth-pair meshing period. The improved method can give higher accuracy in evaluating gear body-induced tooth deflections of spur gears with a pressure angle of 20°.