Luis Béjar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Luis Béjar has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Ariosto Medina
Instituto de Investigaciones en Metalurgia y Materiales, Universidad Michoacana de San Nicolás de Hidalgo, Av. J. Múgica S/N, Morelia 58030, Michoacán, Mexico
4 shared publications - Ismeli Alfonso
Universidad Nacional Autónoma de México
4 shared publications - Claudio Aguilar
Universidad Tecnica Federico Santa Maria
2 shared publications A. Medina
Facultad de Ingeniería Mecánica,Ingeniería Mecánica/Universidad Michoacana de San Nicolás de Hidalgo, Edificio “J”, Ciudad Universitaria. Morelia, Michoacán México C.P. 58000
1 shared publicationAbraham A. Mejía
Facultad de Ingeniería Mecánica,Ingeniería Mecánica/Universidad Michoacana de San Nicolás de Hidalgo, Edificio “J”, Ciudad Universitaria. Morelia, Michoacán México C.P. 58000
1 shared publicationC. Aguilar
Departamento de Ingeniería Metalúrgica y Materiales/Universidad Técnica Federico Santa María, Av. España 1680, Valparaíso, Chile
1 shared publication
Latest Publications
- Open Access
- 1 January 2020
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 25 (2)
Estudio de perfiles de difracción de rayos X de una aleación Ti-13Ta-3Sn obtenida por aleado mecánico
RESUMEN Las aleaciones Ti-β se han vuelto altamente demandadas en la industria, por sus buenas características físicas y químicas. En el presente trabajo, se sintetizó una aleación Ti-13Ta-3Sn (%at) por aleado mecánico con tiempos entre 2 y 100h. Las aleaciones se caracterizaron por difracción de rayos X (DRX) y los patrones se analizaron por el método Rietveld con el software MAUD. Se caracterizaron los cambios microestructurales y la evolución de las fases Ti-α y Ti-β. Se identificó la presencia una nueva fase metaestable fcc y la síntesis de una aleación con un 79,80% en peso de fase Ti-β, ambas con tamaño de cristalita nanométrico.
- 1 January 2020
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 25 (2)
Open AccessEstudio de perfiles de difracción de rayos X de una aleación Ti-13Ta-3Sn obtenida por aleado mecánico
RESUMEN Las aleaciones Ti-β se han vuelto altamente demandadas en la industria, por sus buenas características físicas y químicas. En el presente trabajo, se sintetizó una aleación Ti-13Ta-3Sn (%at) por aleado mecánico con tiempos entre 2 y 100h. Las aleaciones se caracterizaron por difracción de rayos X (DRX) y los patrones se analizaron por el método Rietveld con el software MAUD. Se caracterizaron los cambios microestructurales y la evolución de las fases Ti-α y Ti-β. Se identificó la presencia una nueva fase metaestable fcc y la síntesis de una aleación con un 79,80% en peso de fase Ti-β, ambas con tamaño de cristalita nanométrico.
- 5 December 2019
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 18 (1)
Delumping Strategy to Infer Lubrication Reaction Pathways in Internal Combustion Engines
Lubricant reactions in internal combustion engines follow complex reaction pathways, in which oil (hydrocarbons) and additives form protecting films (known as tribofilms) on the surfaces of the cylinder-piston couple. Up-to-date there is not a fundamental model useful to describe the chemistry involved in formation of these tribofilms, and degradation of oils and additives as result of working time of the engine. One of the main problems associated is the impossible measuring of the actual phenomena inside the engine, at working conditions. In order to model formation of tribofilms, starting by lumping two main groups of lubricating molecules, anti-shear and anti-wear, the lumped kinetics model for degradation products was solved, based on actual data collected in commercial engine workshops. Later these two-lump reaction schemes were delumped into two new systems, each one consisting of three lumps, in order to infer lubricant reaction pathways that form tribofilms and degrade lubricants. Distribution of anti-shear and anti-wear lubricants in tribofilms was predicted by simulation of these two delumped schemes.
- 5 December 2019
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 18 (1)
Delumping Strategy to Infer Lubrication Reaction Pathways in Internal Combustion Engines
Lubricant reactions in internal combustion engines follow complex reaction pathways, in which oil (hydrocarbons) and additives form protecting films (known as tribofilms) on the surfaces of the cylinder-piston couple. Up-to-date there is not a fundamental model useful to describe the chemistry involved in formation of these tribofilms, and degradation of oils and additives as result of working time of the engine. One of the main problems associated is the impossible measuring of the actual phenomena inside the engine, at working conditions. In order to model formation of tribofilms, starting by lumping two main groups of lubricating molecules, anti-shear and anti-wear, the lumped kinetics model for degradation products was solved, based on actual data collected in commercial engine workshops. Later these two-lump reaction schemes were delumped into two new systems, each one consisting of three lumps, in order to infer lubricant reaction pathways that form tribofilms and degrade lubricants. Distribution of anti-shear and anti-wear lubricants in tribofilms was predicted by simulation of these two delumped schemes.
- 1 June 2019
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 25 (S2) , 2630-2631
Scanning Electron Microscopy of the Electrochemical Corrosion Products of a Titanium Based Metallic Foam
- 1 June 2019
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 25 (S2) , 2630-2631
Scanning Electron Microscopy of the Electrochemical Corrosion Products of a Titanium Based Metallic Foam
- Open Access
- 19 July 2018
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 23 (2)
Electrochemical corrosion characterization of nickel aluminides in acid rain
Nickel aluminides have been extensively studied in recent decades to replace superalloys, in some components of aircraft turbines, because they have excellent corrosion resistance. Many industrial cities have the problem of air pollution, which has forced the study of the degradation of these alloys in the presence of acid rain. The aim of this work is to study the electrochemical corrosion behavior of nickel aluminides in a medium of simulated acid rain. Potentiodynamic Polarization, Linear polarization resistance curves, Rp, Nyquist data and Bode curves obtained by electrochemical impedance spectroscopy were used to study the corrosion behavior of two intermetallic compounds. The polarization curves show that both intermetallic Ni3Al and NiAl have very similar corrosion potential, showing a slightly nobler behavior the NiAl intermetallic. The intermetallic Ni3Al has an active-passive behavior where the anode branch presents a general dissolution of the alloy, indicating that it is under cathodic control. NiAl intermetallic shows an active dissolution region, followed by a passive behavior. At longer immersion times, Ni3Al intermetallic has a higher polarization resistance, which means a lower corrosion rate.
- 19 July 2018
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 23 (2)
Open AccessElectrochemical corrosion characterization of nickel aluminides in acid rain
Nickel aluminides have been extensively studied in recent decades to replace superalloys, in some components of aircraft turbines, because they have excellent corrosion resistance. Many industrial cities have the problem of air pollution, which has forced the study of the degradation of these alloys in the presence of acid rain. The aim of this work is to study the electrochemical corrosion behavior of nickel aluminides in a medium of simulated acid rain. Potentiodynamic Polarization, Linear polarization resistance curves, Rp, Nyquist data and Bode curves obtained by electrochemical impedance spectroscopy were used to study the corrosion behavior of two intermetallic compounds. The polarization curves show that both intermetallic Ni3Al and NiAl have very similar corrosion potential, showing a slightly nobler behavior the NiAl intermetallic. The intermetallic Ni3Al has an active-passive behavior where the anode branch presents a general dissolution of the alloy, indicating that it is under cathodic control. NiAl intermetallic shows an active dissolution region, followed by a passive behavior. At longer immersion times, Ni3Al intermetallic has a higher polarization resistance, which means a lower corrosion rate.
- Open Access
- 1 September 2017
- Published by FapUNIFESP (SciELO) in Soldagem & Inspeção
- Vol. 22 (3) , 249-257
Efecto del V y el Si Sobre la Microestructura de Depósitos Realizados con Electrodos Tubulares Revestidos de Alto Contenido de Mn (Hadfield)
Las aleaciones para el relleno superficial Fe-Mn-C (Hadfield) han demostrado una excelente resistencia al desgaste bajo altas cargas dinámicas. En los últimos años se han realizado numerosos estudios para aumentar la resistencia al desgaste y mejorar su desempeño, a través de la introducción de otros elementos de aleación. En el presente trabajo se investiga la microestructura y dureza de los depósitos de relleno con alto contenido de Mn y adiciones de 1.2% de V y 2.4% de Si. Los depósitos estudiados se realizaron utilizando electrodos tubulares revestidos fabricados a escala de laboratorio. Las fases y microconstituyentes en el metal depositado se identificaron mediante microscopía óptica (MO), electrónica de barrido (MEB), difracción de rayos X (DRX), dureza y microdureza. De acuerdo a los resultados obtenidos, la adición de V al sistema aleante originó que la fase predominante fuera la austenita. Además, contribuyó a la formación de carburos de vanadio (VC) en la microestructura de la capa de relleno, sin observarse la presencia de carburos complejos. Por otra parte, la presencia de Si favoreció la formación de una red de ferrita interdendrítica. La adición de estos elementos de aleación mejoró las propiedades de estos depósitos, potencializando su uso en aplicaciones que requieren alta resistencia al desgaste bajo altas cargas.
- 1 September 2017
- Published by FapUNIFESP (SciELO) in Soldagem & Inspeção
- Vol. 22 (3) , 249-257
Open AccessEfecto del V y el Si Sobre la Microestructura de Depósitos Realizados con Electrodos Tubulares Revestidos de Alto Contenido de Mn (Hadfield)
Las aleaciones para el relleno superficial Fe-Mn-C (Hadfield) han demostrado una excelente resistencia al desgaste bajo altas cargas dinámicas. En los últimos años se han realizado numerosos estudios para aumentar la resistencia al desgaste y mejorar su desempeño, a través de la introducción de otros elementos de aleación. En el presente trabajo se investiga la microestructura y dureza de los depósitos de relleno con alto contenido de Mn y adiciones de 1.2% de V y 2.4% de Si. Los depósitos estudiados se realizaron utilizando electrodos tubulares revestidos fabricados a escala de laboratorio. Las fases y microconstituyentes en el metal depositado se identificaron mediante microscopía óptica (MO), electrónica de barrido (MEB), difracción de rayos X (DRX), dureza y microdureza. De acuerdo a los resultados obtenidos, la adición de V al sistema aleante originó que la fase predominante fuera la austenita. Además, contribuyó a la formación de carburos de vanadio (VC) en la microestructura de la capa de relleno, sin observarse la presencia de carburos complejos. Por otra parte, la presencia de Si favoreció la formación de una red de ferrita interdendrítica. La adición de estos elementos de aleación mejoró las propiedades de estos depósitos, potencializando su uso en aplicaciones que requieren alta resistencia al desgaste bajo altas cargas.
- Open Access
- 14 May 2015
- Published by Editorial CSIC in Revista de Metalurgia
- Vol. 51 (2) , e041
High resolution transmission electron microscopy and molecular simulation analysis of ε-Fe2-3N and γ’-Fe4N formation for a nitrided 4140 steel
- 14 May 2015
- Published by Editorial CSIC in Revista de Metalurgia
- Vol. 51 (2) , e041
Open AccessHigh resolution transmission electron microscopy and molecular simulation analysis of ε-Fe2-3N and γ’-Fe4N formation for a nitrided 4140 steel